Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (for HV Model without Entry and Start System)
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424981 IMMOBILISER SYSTEM(for HV Model without Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(for HV Model without Entry and Start System)  B279A12  Engine Immobiliser System Circuit Short to Battery  


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the hybrid vehicle control ECU stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A12 Engine Immobiliser System Circuit Short to Battery Communication line (EFIO-IMI) between the hybrid vehicle control ECU and transponder key ECU assembly is stuck high.
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait 6 seconds.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started Hybrid control system cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A12 -

WIRING DIAGRAM

E366880E24
5.052,0.833 5.365,1.031 0.313,0.198 10 false 11 1.813,0.833 2.219,1.031 0.406,0.198 10 false IMI 0.563,1.948 1.51,2.177 0.948,0.229 10 false H44 5.25,2.115 6.635,2.625 1.385,0.51 10 false Transponder Key ECU Assembly 2.115,0.823 2.927,1.052 0.813,0.229 10 false 25 5.302,0.844 5.708,1.042 0.406,0.198 10 false EFIO 1.323,0.385 1.74,0.594 0.417,0.208 10 false 12 V 5.24,1.948 5.646,2.146 0.406,0.198 10 false H74 0.563,2.115 2.708,2.667 2.146,0.552 10 false Hybrid Vehicle Control ECU

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or hybrid vehicle control ECU is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the hybrid vehicle control ECU and transponder key ECU assembly.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HYBRID VEHICLE CONTROL ECU

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HYBRID VEHICLE CONTROL ECU
a.

Disconnect the H74 transponder key ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H74-11 (EFIO) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HYBRID VEHICLE CONTROL ECU (TERMINAL IMI)

NG

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
3.CHECK HYBRID VEHICLE CONTROL ECU (TERMINAL IMI)
a.

Connect the transponder key ECU assembly connector.


b.

Using an oscilloscope, check the waveform.

E438561C03
4.438,0.135 4.854,0.385 0.417,0.25 3.865,2.188 4.146,1.281 true 3.531,4.552 3.406,4.073 true 3.104,4.563 3.208,4.073 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 3.229,3.031 3.542,3.188 0.313,0.156 10 false *b 2.99,4.573 3.302,4.729 0.313,0.156 10 false *c 3.771,2.219 4.063,2.458 0.292,0.24 10 false IMI 4.531,0.188 4.969,0.427 0.438,0.24 10 false H44 3.542,4.573 3.833,4.813 0.292,0.24 10 false *d 0.875,4.031 1.292,4.24 0.417,0.208 10 false GND
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
H44-25 (IMI) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the H44 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H74-11 (EFIO) - H44-25 (IMI) Always Below 1 Ω
H74-11 (EFIO) or H44-25 (IMI) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR