Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _088664 CRUISE CONTROL _0424997 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for HV Model) C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for HV Model)  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly outputs a signal to the hybrid vehicle control ECU. The hybrid vehicle control ECU uses this signal to control cancellation of vehicle speed by the dynamic radar cruise control. When the hybrid vehicle control ECU determines that terminals STP and ST1- of the stop light switch assembly are both less than 1 V, DTC P057162 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P057162 Brake Switch "A" Signal Compare Failure When the ignition switch is ON and the dynamic radar cruise control system is operating, the hybrid vehicle control ECU detects that the voltage at terminal STP and ST1- are both less than 1 V for approximately 0.5 seconds or more.
·

Harness or connector

·

Stop light switch assembly

·

Hybrid vehicle control ECU


Radar Cruise1

WIRING DIAGRAM

C432274E07
5.323,3.875 6.896,4.25 1.573,0.375 10 false Certification ECU (Smart Key ECU Assembly)* 2.833,3.885 5,4.417 2.167,0.531 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.333,3.688 5.792,3.885 0.458,0.198 10 false H45 2.833,3.698 3.292,3.896 0.458,0.198 10 false A38 3.906,3.302 4.365,3.5 0.458,0.198 10 false STP2 5.76,3.292 6.219,3.49 0.458,0.198 10 false STP1 4.354,3.208 4.688,3.406 0.333,0.198 10 false 37 5.51,3.208 5.823,3.406 0.313,0.198 10 false 21 2.958,2.49 6.938,2.688 3.979,0.198 10 false Stop Light Switch Assembly 2.969,2.323 3.427,2.521 0.458,0.198 10 false A63 5.479,1.469 5.792,1.667 0.313,0.198 10 false 5 5.49,0.667 5.802,0.865 0.313,0.198 10 false 6 5.677,1.563 6.135,1.76 0.458,0.198 10 false ST1- 5.677,0.76 6.135,0.958 0.458,0.198 10 false STP 5.313,2.458 7.073,2.677 1.76,0.219 10 false Hybrid Vehicle Control ECU 4.167,0.75 4.479,0.948 0.313,0.198 10 false L 4.156,1.552 4.469,1.75 0.313,0.198 10 false L 3.573,0.885 3.885,1.083 0.313,0.198 10 false B 3.573,1.396 3.885,1.594 0.313,0.198 10 false B 3.573,1.906 3.885,2.104 0.313,0.198 10 false GND 4.333,0.677 4.646,0.875 0.313,0.198 10 false 3 4.344,1.469 4.656,1.667 0.313,0.198 10 false 5 3.406,0.792 3.719,0.99 0.313,0.198 10 false 7 3.406,1.292 3.719,1.49 0.313,0.198 10 false 6 3.396,1.813 3.708,2.01 0.313,0.198 10 false 2 2.396,1.052 3.01,1.25 0.615,0.198 10 false STOP 2.073,1.573 3.115,1.833 1.042,0.26 10 false ECU-IGP NO. 3 0.469,0.885 1.729,1.219 1.26,0.333 10 false from AM1 Fuse 0.458,1.417 1.469,1.792 1.01,0.375 10 false from IGP Relay 5.313,2.281 5.771,2.479 0.458,0.198 10 false A68 0.229,4.281 2.302,4.625 2.073,0.344 10 false *: w/ Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the A63 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A63-7 (B) - Body ground Always 11 to 14 V
A63-6 (B) - Body ground Ignition switch ON 11 to 14 V
A63-6 (B) - Body ground Ignition switch off Below 1 V



d.

Connect the A63 stop light switch assembly connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A68 hybrid vehicle control ECU connectors.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.*

*: w/ Entry and Start System



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A68-5 (ST1-) - A63-5 (L) Always Below 1 Ω
A68-6 (STP) - A63-3 (L) Always Below 1 Ω
A68-5 (ST1-) or A63-5 (L) - Body ground Always 10 kΩ or higher
A68-6 (STP) or A63-3 (L) - Body ground Always 10 kΩ or higher



f.

Connect the H45 certification ECU (smart key ECU assembly) connector.*

*: w/ Entry and Start System



g.

Connect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


h.

Connect the A63 stop light switch assembly connector.


i.

Connect the A68 hybrid vehicle control ECU connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR