Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model) › 2020.03–2020.07
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  P033562  Crankshaft Position Sensor "A" Signal Compare Failure  


DESCRIPTION

These DTCs are stored when the engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
P033562 Crankshaft Position Sensor "A" Signal Compare Failure The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication do not match. (1-trip detection logic*)
·

SFI system

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation:

Allow the engine to idle for 10 seconds or more, and then engine speed of 1000 rpm or more for 20 seconds or more.



*: Only detected while a malfunction is present and the ignition switch is ON.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

When a malfunction occurs and the vehicle speed signal sent via either direct line or CAN communication indicates no vehicle speed, there is no effect on vehicle behavior. (A malfunction is detected after the ignition switch is turned to ON.)

·

When a malfunction occurs and the vehicle speed signal sent via either direct line or CAN communication indicates that the vehicle is moving, the engine cannot be started. However, the engine can be started after the ignition switch has been turned off.


·

When a malfunction occurs and the vehicle speed signal sent via either direct line or CAN communication indicates no vehicle speed, there is no effect on vehicle behavior.

·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving:

If the following conditions are met, it can be determined that the malfunction is not in the CAN communication system but in the direct line (NE).
-

When the engine switch is pressed, the system controls the engine based on the starter OFF permission flag (perfect injection signal judgment) via CAN communication, causing the engine to stop cranking.

-

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via CAN communication, causing the engine to stop cranking.


If the following conditions are met, it can be determined that the malfunction is not in the direct line (NE) but in the CAN communication system.
-

When the engine switch is pressed, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.

-

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.


If the following conditions are met, it can be determined that there is a malfunction in both the CAN communication system and the direct line (NE).
-

When the engine switch is pressed, the engine stops cranking after 6 seconds.

-

When the engine switch is pressed and held, the engine cranks for up to 30 seconds.




Related Data List and Active Test Items
DTC No. Data List and Active Test
P033562
Power Source Control
·

Engine Driving Condition (Line)

·

Engine Speed



WIRING DIAGRAM

B478908E42
1.094,1.573 2.479,1.854 1.385,0.281 10 false A54 1.083,1.729 1.635,2.021 0.552,0.292 10 false ECM 0.885,2.219 2.833,2.531 1.948,0.313 10 false : CAN Communication Line 1.51,0.76 2.063,1.052 0.552,0.292 10 false NEO 1.906,0.75 2.854,1.073 0.948,0.323 10 false 16 5.281,0.74 5.833,1.031 0.552,0.292 10 false 15 5.531,0.74 6.083,1.031 0.552,0.292 10 false NE 5.75,0.375 6.302,0.667 0.552,0.292 10 false +B 6.125,0.917 6.677,1.208 0.552,0.292 10 false IC 5.292,1.552 6.521,1.854 1.229,0.302 10 false H45 5.281,1.708 6.833,2.313 1.552,0.604 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.READ VALUE USING GTS (ENGINE DRIVING CONDITION (LINE), ENGINE SPEED)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Driving Condition (Line) Engine state Stop or Driving Stop: Engine stopped
Run: Engine running
-
Body Electrical > Power Source Control > Data List
Tester Display
Engine Driving Condition (Line)
50003 454 401
Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed 0 to 16383.75 rpm Fluctuates in accordance with actual engine speed -
Body Electrical > Power Source Control > Data List
Tester Display
Engine Speed
50003 454 101
OK:

The GTS display changes correctly in response to the engine condition.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A54 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-15 (NE) - A54-16 (NEO) Always Below 1 Ω
H45-15 (NE) or A54-16 (NEO) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the H45 certification ECU (smart key ECU assembly) connector.


b.

Connect the A54 ECM connector.


c.
B574625C16
1.344,0.031 1.729,0.24 0.385,0.208 2.146,1.938 1.844,1.938 1.844,1.938 1.313,0.823 true 0.156,0.094 0.469,0.25 0.313,0.156 10 false *a 1.417,0.052 1.729,0.208 0.313,0.156 10 false H45 2.208,1.854 2.646,2.042 0.438,0.188 10 false NE
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Using an oscilloscope, check the engine speed input signal waveform at the terminal of the certification ECU (smart key ECU assembly).

OK:
Tester Connection Condition Specified Condition
H45-15 (NE) - Body ground Engine stopped No pulse generation
Engine running Pulse generation



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG