Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _57 Power Source / Network _088060 NETWORKING _0424238 CAN COMMUNICATION SYSTEM(for HV Model) C

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  U115087  Lost Communication with Hybrid Powertrain Control Module (ch2) Missing Message  


DESCRIPTION

The hybrid vehicle ECU assembly communicates with the ECM and skid control ECU (brake booster assembly). When the hybrid vehicle ECU assembly does not receive data from the ECM or skid control ECU (brake booster assembly), the hybrid vehicle ECU assembly stores DTC U115087.

SFI SYSTEM (M15A-FXE)
DTC No. Detection Item DTC Detection Condition Trouble Area Note
U115087 Lost Communication with Hybrid Powertrain Control Module (ch2) Missing Message No communication from the Hybrid vehicle control ECU continues.
·

Hybrid vehicle control ECU main line or connector

·

Hybrid vehicle control ECU


ECM

ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)
DTC No. Detection Item DTC Detection Condition Trouble Area Note
U115087 Lost Communication with Hybrid Powertrain Control Module (ch2) Missing Message No communication from the Hybrid vehicle control ECU continues.
·

Hybrid vehicle control ECU main line or connector

·

Hybrid vehicle control ECU


Brake booster with master cylinder assembly

WIRING DIAGRAM

C434123E01
1.198,0.74 1.635,0.927 0.438,0.188 10 false CAN+ 1.219,1.281 1.656,1.469 0.438,0.188 10 false CAN- 0.865,1.656 1.302,1.844 0.438,0.188 10 false A53 0.875,1.813 1.333,2.031 0.458,0.219 10 false ECM 1.635,0.625 1.865,0.802 0.229,0.177 10 false 12 1.635,1.177 1.865,1.354 0.229,0.177 10 false 25 3.344,0.625 3.49,0.802 0.146,0.177 10 false 9 3.281,1.156 3.469,1.333 0.188,0.177 10 false 20 4.583,0.625 4.885,0.833 0.302,0.208 10 false 10 4.583,1.167 4.802,1.344 0.219,0.177 10 false 21 5.167,0.635 5.385,0.813 0.219,0.177 10 false 24 5.177,1.146 5.396,1.323 0.219,0.177 10 false 11 5.417,0.604 5.854,0.792 0.438,0.188 10 false CA3P 5.417,1.146 5.854,1.333 0.438,0.188 10 false CA3N 5.198,1.667 5.635,1.854 0.438,0.188 10 false H44 5.198,1.823 7.083,2.156 1.885,0.333 10 false Hybrid Vehicle Control ECU 2.469,2.771 2.906,2.958 0.438,0.188 10 false CA2H 1.271,3.177 1.708,3.365 0.438,0.188 10 false GND1 2.917,2.75 3.146,2.927 0.229,0.177 10 false 30 2.917,3.292 3.146,3.469 0.229,0.177 10 false 29 3.354,2.76 3.5,2.938 0.146,0.177 10 false 7 3.302,3.323 3.49,3.5 0.188,0.177 10 false 18 1.219,3.802 1.563,3.99 0.344,0.188 10 false A38 1.219,3.958 2.865,4.344 1.646,0.385 10 false Brake Booster with Master Cylinder Assembly 3.458,3.792 3.844,3.979 0.385,0.188 10 false H116 3.438,3.948 5.104,4.354 1.667,0.406 10 false No. 5 Global CAN Junction Connector 2.51,3.302 2.948,3.49 0.438,0.188 10 false CA2L 1.281,3.458 1.719,3.646 0.438,0.188 10 false GND2 1.271,2.854 1.708,3.042 0.438,0.188 10 false IGR 0.365,2.458 1.719,2.615 1.354,0.156 10 false ECU-IGR NO.3 1.031,2.76 1.26,2.938 0.229,0.177 10 false 23 1.031,3.365 1.26,3.542 0.229,0.177 10 false 39 1.031,3.052 1.26,3.229 0.229,0.177 10 false 26 1.802,2.302 3.323,2.531 1.521,0.229 10 false from IGR-NO. 1 Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Before replacing the hybrid vehicle control ECU assembly, refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR DTC
a.

Read each DTC and check the diagnosis pattern using the table below.

Powertrain > Engine > Trouble Codes
50001 372
Chassis > Brake > Trouble Codes
50001 435
Pattern DTC output part name
(Display on GTS / Output DTC)
Engine Brake
Pattern 1 U115087 U115087
Pattern 2 U115087 -
Pattern 3 - U115087


Result:
Result Proceed to
Pattern 1 A
Pattern 2 B
Pattern 3 C



A

2.CHECK FOR CAN BUS MAIN WIRE

B

23.CHECK HARNESS AND CONNECTOR (ECM - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

C

24.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BODY GROUND)
2.CHECK FOR CAN BUS MAIN WIRE
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
H116-9 (CANH) - H116-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
H116-9 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH short to ground
H116-20 (CANL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL short to ground
H116-9 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
H116-20 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
NG (Open circuit in CAN main bus lines) B
NG (Short circuit between bus lines) C
NG (+B short or Short to ground) D



A

3.CLEAR DTC

B

5.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY MAINE BUS)

C

11.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY MAINE BUS)

D

17.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY MAINE BUS)
3.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372
Chassis > Brake > Clear DTCs
50002 435

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
DTC U115087 is output A
DTC U115087 is not output B



A

B

5.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY MAINE BUS)
a.

Disconnect the H116 No. 5 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H116-7 (CANH) - H116-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK FOR OPEN IN CAN BUS WIRE (HYBRID VEHICLE CONTROL ECU MAINE BUS)

NG

8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
6.CHECK FOR OPEN IN CAN BUS WIRE (HYBRID VEHICLE CONTROL ECU MAINE BUS)
a.

Disconnect the H116 No. 5 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H116-10 (CANH) - H116-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK FOR OPEN IN CAN BUS WIRE (ECM MAINE BUS)

NG

9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (HYBRID VEHICLE CONTROL ECU)
7.CHECK FOR OPEN IN CAN BUS WIRE (ECM MAINE BUS)
a.

Disconnect the H116 No. 5 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H116-7 (CANH) - H116-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 5 GLOBAL CAN JUNCTION CONNECTOR

NG

10.CHECK FOR OPEN IN CAN BUS BRANCH WIRE (ECM)
8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
a.

Reconnect the H116 No. 5 global CAN junction connector.


b.

Disconnect the A38 brake booster with master cylinder assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-30 (CA2H) - A38-29 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (HYBRID VEHICLE CONTROL ECU)
a.

Reconnect the H116 No. 5 global CAN junction connector.


b.

Disconnect the H44 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H44-23 (CA3P) - H44-11 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (HYBRID VEHICLE CONTROL ECU - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

10.CHECK FOR OPEN IN CAN BUS BRANCH WIRE (ECM)
a.

Reconnect the H116 No. 5 global CAN junction connector.


b.

Disconnect the A53 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A53-12 (CAN+) - A53-25 (CAN-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (ECM - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

11.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY MAINE BUS)
a.

Disconnect the H116 No. 5 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H116-7 (CANH) - H116-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK FOR SHORT IN CAN BUS WIRES (HYBRID VEHICLE CONTROL ECU MAINE BUS)

NG

14.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
12.CHECK FOR SHORT IN CAN BUS WIRES (HYBRID VEHICLE CONTROL ECU MAINE BUS)
a.

Disconnect the H116 No. 5 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H116-10 (CANH) - H116-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK FOR SHORT IN CAN BUS WIRES (ECM MAINE BUS)

NG

15.CHECK FOR OPEN IN CAN BUS MAIN WIRE (HYBRID VEHICLE CONTROL ECU)
13.CHECK FOR SHORT IN CAN BUS WIRES (ECM MAINE BUS)
a.

Disconnect the H116 No. 5 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H116-7 (CANH) - H116-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 5 GLOBAL CAN JUNCTION CONNECTOR

NG

16.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
14.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
a.

Reconnect the H116 No. 5 global CAN junction connector.


b.

Disconnect the A38 brake booster with master cylinder assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-30 (CA2H) - A38-29 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

15.CHECK FOR OPEN IN CAN BUS MAIN WIRE (HYBRID VEHICLE CONTROL ECU)
a.

Reconnect the H116 No. 5 global CAN junction connector.


b.

Disconnect the H44 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H44-23 (CA3P) - H44-11 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (HYBRID VEHICLE CONTROL ECU - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

16.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.

Reconnect the H116 No. 5 global CAN junction connector.


b.

Disconnect the A53 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A53-12 (CAN+) - A53-25 (CAN-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (ECM - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

17.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY MAINE BUS)
a.

Disconnect the H116 No. 5 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H116-7 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H116-18 (CANL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H116-7 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H116-18 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY MAINE BUS)

NG

20.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
18.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY MAINE BUS)
a.

Disconnect the H116 No. 5 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H116-10 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H116-21 (CANL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H116-10 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H116-21 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY MAINE BUS)

NG

21.CHECK FOR OPEN IN CAN BUS MAIN WIRE (HYBRID VEHICLE CONTROL ECU)
19.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY MAINE BUS)
a.

Disconnect the H116 No. 5 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H116-7 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H116-18 (CANL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H116-7 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H116-18 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 5 GLOBAL CAN JUNCTION CONNECTOR

NG

22.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
20.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
a.

Reconnect the H116 No. 5 global CAN junction connector.


b.

Disconnect the A38 brake booster with master cylinder assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-30 (CA2H) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A38-29 (CA2L) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A38-30 (CA2H) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A38-29 (CA2L) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

21.CHECK FOR OPEN IN CAN BUS MAIN WIRE (HYBRID VEHICLE CONTROL ECU)
a.

Reconnect the H116 No. 5 global CAN junction connector.


b.

Disconnect the H44 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H44-23 (CA3P) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H44-11 (CA3N) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H44-23 (CA3P) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H44-11 (CA3N) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (HYBRID VEHICLE CONTROL ECU - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

22.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.

Reconnect the H116 No. 5 global CAN junction connector.


b.

Disconnect the A53 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A53-12 (CAN+) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A53-25 (CAN-) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A53-12 (CAN+) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A53-25 (CAN-) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (ECM - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

23.CHECK HARNESS AND CONNECTOR (ECM - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the A53 ECM connector.


b.

Disconnect the H116 No. 5 global CAN junction connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A53-12(CAN+) - H116-9(CANH) Always Below 1 Ω
A53-25(CAN-) - H116-20(CANL) Always Below 1 Ω
A53-12(CAN+) or H116-20(CANL) - Body ground Always 10 kΩ or higher
A53-25(CAN-) or H116-20(CANL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BODY GROUND)
a.

Disconnect the A38 brake booster with master cylinder assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-26 (GND1) - Body ground Always Below 1 Ω
A38-39 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

25.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - POWER SOURCE)
a.

Disconnect the A38 brake booster with master cylinder assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-23 (IGR) - Body ground Ignition switch ON 11 to 14 V
A38-23 (IGR) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR