Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2020.03–2020.09
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0420309 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B007313  Second Row Left Seat Belt Pretensioner Deployment Control Circuit Open  


DESCRIPTION

The left side 2nd seat pretensioner squib circuit consists of the airbag sensor assembly and rear seat outer belt assembly LH.

The airbag sensor assembly uses this circuit to deploy the pretensioner when deployment conditions are met.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B007313 Second Row Left Seat Belt Pretensioner Deployment Control Circuit Open
·

The airbag sensor assembly detects an open in the left side 2nd seat pretensioner squib circuit for 2 seconds

·

Rear seat outer belt assembly LH malfunction

·

Airbag sensor assembly malfunction


·

Harness or connector

·

Rear seat outer belt assembly LH

·

Airbag sensor assembly


Comes on Applies to check mode

WIRING DIAGRAM

B502460E67
4.896,3.083 6.854,3.51 1.958,0.427 10 false Airbag Sensor Assembly 4.885,2.917 6.531,3.094 1.646,0.177 10 false O24 4.688,1.333 4.875,1.583 0.188,0.25 10 false 13 4.688,1.896 4.917,2.167 0.229,0.271 10 false 14 4.958,1.333 5.76,1.979 0.802,0.646 10 false PLR+ 4.958,1.896 5.76,2.542 0.802,0.646 10 false PLR- 0.875,2.406 1.99,2.594 1.115,0.188 10 false O15 0.875,2.573 3.344,3.375 2.469,0.802 10 false Rear Seat Outer Belt Assembly LH 2.083,1.333 2.885,1.979 0.802,0.646 10 false 1 2.083,1.885 2.885,2.531 0.802,0.646 10 false 2 1.729,1.333 2.531,1.979 0.802,0.646 10 false RL+ 1.75,1.885 2.552,2.531 0.802,0.646 10 false RL-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

To perform the simulation method, select Check Mode with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST



PROCEDURE

1.CHECK CURRENT DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Post-procedure1

c.

None


Result:
Result Proceed to
Current B007313 is output A
History B007313 is output B



A

2.CHECK CONNECTION OF CONNECTORS

B

USE SIMULATION METHOD TO CHECK

2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the rear seat outer belt assembly LH and airbag sensor assembly.

OK:

The connectors are properly connected.



Post-procedure1

d.

None


Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.
C422858C02
0.521,1.021 0.521,1.635 false 1.365,0.521 1.365,0.885 false 2.469,1.188 2.771,1.625 0.302,0.438 10 false *2 0.448,1.656 0.896,1.99 0.448,0.333 10 false *1 1.281,0.323 1.583,0.51 0.302,0.188 10 false *3
*1 Rear Seat Outer Belt Assembly LH
*2 Airbag Sensor Assembly
*3 Wire Harness


Disconnect the connectors from the rear seat outer belt assembly LH and airbag sensor assembly.


Procedure1

b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.



c.

Check that the short springs of the activation prevention mechanism of the wire harness connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Post-procedure1

d.

None


Result:
Proceed to
OK
NG



OK

4.CHECK REAR SEAT OUTER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK REAR SEAT OUTER BELT ASSEMBLY LH
a.
C422851C07
0.396,2.25 0.771,2.5 0.375,0.25 0.667,0.667 0.667,1.063 false 1.802,2.313 1.979,2.313 false 1.49,0.656 1.49,1.052 false 0.594,1.073 0.99,1.417 0.396,0.344 10 false *1 2.26,0.823 2.573,1.156 0.313,0.333 10 false *2 1.813,0.51 2.146,0.969 0.333,0.458 10 false A 1.656,0.51 1.792,0.76 0.135,0.25 10 false B 1.146,0.51 1.323,0.771 0.177,0.26 10 false C 0.781,0.51 0.948,0.729 0.167,0.219 10 false D 0.448,2.281 0.792,2.5 0.344,0.219 10 false O15 2.01,2.219 2.448,2.563 0.438,0.344 10 false SST 0.344,1.719 0.646,2 0.302,0.281 10 false *a 1.417,1.073 1.698,1.292 0.281,0.219 10 false *3
*1 Rear Seat Outer Belt Assembly LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Rear Seat Outer Belt Assembly LH)


Connect the connector to the airbag sensor assembly.


b.

Connect the white wire side of SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the rear seat outer belt assembly LH for measurement, as this may lead to a serious injury due to pretensioner deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

f.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.CHECK REAR SEAT OUTER BELT ASSEMBLY LH
5.CHECK REAR SEAT OUTER BELT ASSEMBLY LH

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTC B007313 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B007313 is not output A
B007313 is output B


Post-procedure1

c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



e.

Disconnect SST from connector C.



A

REPLACE REAR SEAT OUTER BELT ASSEMBLY LH

B

6.CHECK WIRE HARNESS (OPEN)
6.CHECK WIRE HARNESS (OPEN)

Pre-procedure1

a.
C422852C07
0.604,2.375 0.958,2.615 0.354,0.24 1.531,2.333 1.844,2 true 1.031,2 1.333,2.333 true 0.583,1 0.583,0.667 false 1.417,1 1.417,0.667 false 0.5,1.021 0.75,1.333 0.25,0.313 10 false *1 2.406,0.833 2.781,1.271 0.375,0.438 10 false *2 1.948,0.51 2.135,0.792 0.188,0.281 10 false A 1.573,0.51 1.729,0.781 0.156,0.271 10 false B 1.063,0.51 1.208,0.781 0.146,0.271 10 false C 0.688,0.51 0.833,0.792 0.146,0.281 10 false D 1.885,1.917 2.188,2.208 0.302,0.292 10 false RL- 0.729,1.917 1.01,2.135 0.281,0.219 10 false RL+ 0.354,1.844 0.75,2.135 0.396,0.292 10 false *a 0.635,2.396 1,2.708 0.365,0.313 10 false O15 1.365,1.021 1.667,1.333 0.302,0.313 10 false *3
*1 Rear Seat Outer Belt Assembly LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Rear Seat Outer Belt Assembly LH)


Disconnect the connector from the airbag sensor assembly.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O15-1 (RL+) - O15-2 (RL-) Always Below 1 Ω



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CLEAR DTC
a.
C422848C02
0.813,0.833 0.813,1.156 false 0.927,0.688 1.083,1 0.156,0.313 10 false D 1.083,0.688 1.229,0.948 0.146,0.26 10 false C 1.583,0.688 1.74,0.948 0.156,0.26 10 false B 1.74,0.688 1.979,1 0.24,0.313 10 false A 2.188,1 2.625,1.344 0.438,0.344 10 false *2 0.74,1.177 0.99,1.417 0.25,0.24 10 false *1
*1 Rear Seat Outer Belt Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the rear seat outer belt assembly LH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

e.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC
8.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTC B007313 may be output at this time, but they are not related to this check.



Post-procedure1

c.

None


Result:
Result Proceed to
B007313 is not output A
B007313 is output B



A

USE SIMULATION METHOD TO CHECK

B