Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM36W0E _56 Audio / Visual / Telematics _088657 PARK ASSIST / MONITORING _0425251 BLIND SPOT MONITOR SYSTEM Y

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the blind spot monitor system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:

If there are any scratches or impact marks on the rear bumper, perform the blind spot monitor beam axis confirmation. If any abnormalities are found, perform the blind spot monitor sensor installation condition inspection.


Result:
Proceed to
NEXT



NEXT

3.INSPECT AUXILIARY BATTERY VOLTAGE
3.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

for Gasoline Model:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

for HV Model:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B




A

5.CHECK FOR DTC AND FREEZE FRAME DATA*

B

5.CHECK FOR DTC AND FREEZE FRAME DATA*
a.

Check for DTCs.

Body Electrical > Blind Spot Monitor "B" > Trouble Codes
50001 460
Body Electrical > Blind Spot Monitor "A" > Trouble Codes
50001 461

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Recheck for DTCs.

Body Electrical > Blind Spot Monitor "B" > Trouble Codes
50001 460
Body Electrical > Blind Spot Monitor "A" > Trouble Codes
50001 461

e.

Record or print DTCs and freeze frame data, if necessary.

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B




A

6.PROBLEM SYMPTOMS TABLE

B

6.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table. A
Fault is listed in Problem Symptoms Table. B


HINT:

If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING




A

7.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM*

B

7.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM*

NEXT

8.ADJUST, REPAIR OR REPLACE
8.ADJUST, REPAIR OR REPLACE
Result:
Result Proceed to
When adjusting or repairing A
When replacing B



A

9.CLEAR DTC

B

10.PERFORM BEAM AXIS CONFIRMATION*
9.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Blind Spot Monitor "B" > Clear DTCs
50002 460
Body Electrical > Blind Spot Monitor "A" > Clear DTCs
50002 461
Result:
Proceed to
NEXT




NEXT

10.PERFORM BEAM AXIS CONFIRMATION*
10.PERFORM BEAM AXIS CONFIRMATION*
a.

Confirm the blind spot monitor beam axis display and perform the blind spot monitor beam axis adjustment.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

11.PERFORM CONFIRMATION TEST
11.PERFORM CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END