Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0425342 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  TERMINALS OF ECU  


TERMINALS OF ECU


C343118C02
1.323,0.667 1.885,0.958 0.563,0.292 0.323,0.25 0.635,0.448 0.313,0.198 10 false *a 1.458,0.729 1.917,0.927 0.458,0.198 10 false A38
*a Component without harness connected
(Skid Control ECU (Brake Booster with Master Cylinder Assembly))
- -


Terminal No. (Symbol) Terminal Description
1 (MRO1) Motor power supply output 1
2 (MRI1) Motor power supply input 1
3 (FR+) Front speed sensor RH (+) power supply output
4 (FR-) Front speed sensor RH (-) signal input
5 (+BI2) +BI2 power source input
6 - (Not used)
7 (RR+) Rear speed sensor RH (+) power supply output
8 (RR-) Rear speed sensor RH (-) signal input
9 (IGP) IGP power source input
10 - (Not used)
11 (SP1) Speed sensor signal output
12 (STP) Stop light switch assembly input
13 (SKG1) Brake pedal stroke sensor assembly ground 1
14 (+BS) ABS solenoid drive power output
15 (+BI1) +BI1 power source input
16 (LBL) Brake fluid level warning switch (Brake booster with master cylinder assembly) input
17 (SKS1) Brake pedal stroke sensor assembly signal input 1
18 (CSW) VSC OFF switch input
19 (SKS2) Brake pedal stroke sensor assembly signal input 2
20 - (Not used)
21 (VSK2) Brake pedal stroke sensor assembly power supply output 2
22 (STPO) Stop light control relay (Stop light switch assembly) output
23 (IGR) IGR power source input
24 (CTY) Front door courtesy light switch assembly input (for driver side)
25 (VSK1) Brake pedal stroke sensor assembly power supply output 1
26 (GND1) Skid control ECU (Brake booster with master cylinder assembly) ground 1
27 (MRO2) Motor power supply output 2
28 (MRI2) Motor power supply input 2
29 (CA2L) CAN communication line 2 (L)
30 (CA2H) CAN communication line 2 (H)
31 (FL+) Front speed sensor LH (+) power supply output
32 (FL-) Front speed sensor LH (-) signal input
33 (SKG2) Brake pedal stroke sensor assembly ground 2
34 (RL+) Rear speed sensor LH (+) power supply output
35 (RL-) Rear speed sensor LH (-) signal input
36 - (Not used)
37 (STP2) Stop light control relay (Stop light switch assembly) input
38 - (Not used)
39 (GND2) Skid control ECU (Brake booster with master cylinder assembly) ground 2
40 (+BM) ABS motor drive power output
41 (BM) ABS motor relay power supply input
42 (CA1L) CAN communication line 1 (L)
43 (CA1H) CAN communication line 1 (H)
44 (SFRR) Front ABS reduction solenoid RH (-) output
45 (SFLR) Front ABS reduction solenoid LH (-) output
46 (SRRR) Rear ABS reduction solenoid RH (-) output
47 (SRLR) Rear ABS reduction solenoid LH (-) output
48 (SFRH) Front ABS holding solenoid RH (-) output
49 (SFLH) Front ABS holding solenoid LH (-) output
50 (SRRH) Rear ABS holding solenoid RH (-) output
51 (SRLH) Rear ABS holding solenoid LH (-) output
52 (BS) ABS solenoid relay power supply input


TERMINAL INSPECTION


a.

Disconnect the connector and measure the voltage or resistance on the wire harness side.

C343116C29
1.5,0.75 2,1 0.5,0.25 0.25,0.208 0.563,0.406 0.313,0.198 10 false *a 1.604,0.781 2.021,0.979 0.417,0.198 10 false A38
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))
- -


HINT:

The voltage cannot be measured with the connector connected to the skid control ECU (brake booster with master cylinder assembly) as the connector is watertight.


Standard
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A38-2 (MRI1) - Body ground Motor power supply input 1 Always 11 to 14 V
A38-5 (+BI2) - Body ground +BI2 power source input Always 11 to 14 V
A38-9 (IGP) - Body ground IGP power source input Ignition switch ON 11 to 14 V
A38-12 (STP) - Body ground Stop light switch assembly input Stop light switch assembly on → off
(Brake pedal depressed → released)
11 to 14 V → 1.5 V or less
A38-15 (+BI1) - Body ground +BI1 power source input Always 11 to 14 V
A38-16 (LBL) - Body ground Brake fluid level warning switch (Brake booster with master cylinder assembly) input Brake fluid level warning switch off → on 1.84 to 2.16 kΩ → Below 1 Ω
A38-18 (CSW) - Body ground VSC OFF switch input VSC OFF switch held on → off (Released) Below 1 Ω → 10 kΩ or higher
A38-22 (STPO) - Body ground Stop light control relay (Stop light switch assembly) output Always 11 to 14 V
A38-23 (IGR) - Body ground IGR power source input Ignition switch ON 11 to 14 V
A38-24 (CTY) - Body ground Front door courtesy light switch assembly input (for driver side) Driver door closed → open 11 to 14 V → 1.5 V or less
A38-26 (GND1) - Body ground Skid control ECU (Brake booster with master cylinder assembly) ground 1 Always Below 1 Ω
A38-28 (MRI2) - Body ground Motor power supply input 2 Always 11 to 14 V
A38-37 (STP2) - Body ground Stop light control relay (Stop light switch assembly) input Stop light switch assembly on → off
(Brake pedal depressed → released)
11 to 14 V → 1.5 V or less
A38-39 (GND2) - Body ground Skid control ECU (Brake booster with master cylinder assembly) ground 2 Always Below 1 Ω
A38-41 (BM) - Body ground ABS motor relay power supply input Always 11 to 14 V
A38-52 (BS) - Body ground ABS solenoid relay power supply input Always 11 to 14 V