FREEZE FRAME DATA/INFORMATION
Using the GTS, check the vehicle condition (ECU, sensor) when a DTC is output.
CHECK FREEZE FRAME DATA AND INFORMATION WHEN DTC WAS STORED
Freeze Frame Data is stored when a DTC is output.
Once Freeze Frame Data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.
Check the Freeze Frame Data when a DTC is output.
Select a DTC to display the Freeze Frame Data.
Check the Freeze Frame Data for the output DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled - Unit | Total Distance Traveled unit | km / mile | - | - |
| Total Distance Traveled | Total distance traveled | Min.: 0
Max.: 16777215 |
- | - |
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Lateral G | Lateral G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
| Forward and Rearward G | Forward and rearward G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2 |
During acceleration/ deceleration: Changes in proportion with acceleration |
| Yaw Rate Sensor Value | Yaw rate sensor | Min.: -128°/s
Max.: 127°/s |
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Steering Angle Value | Steering sensor | Min.: -3276.8°
Max.: 3276.7° |
Turning left: 0.0 to 3276.7
Turning right: -3276.8 to 0.0° |
- |
| MT Voltage Value | ABS motor drive voltage value | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| Solenoid Power Supply Voltage | Solenoid power supply voltage value | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | - |
| Engine Revolutions | Engine speed | Min.: 0 rpm
Max.: 65535 rpm |
Engine stopped: 0 rpm | When engine speed is constant: No large fluctuations |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle | Min.: 0.0%
Max.: 127.5% |
Accelerator pedal released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
| Shift Lever Position | Shift lever position information | fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input | Actual shift lever position | - |
| TRC(TRAC)/VSC OFF Mode | TRC(TRAC)/VSC off mode | Normal mode (TRC(TRAC) ON/VSC ON) / TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / Not defined / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) | Normal mode (TRC(TRAC) ON/VSC ON): Normal mode TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRAC off mode Not
defined: Not defined VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode |
- |
| FR Target Oil Pressure | Front wheel RH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 Mpa |
- | Different according to target oil pressure of each wheel |
| FL Target Oil Pressure | Front wheel LH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 Mpa |
- | Different according to target oil pressure of each wheel |
| RR Target Oil Pressure | Rear wheel RH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 Mpa |
- | Different according to target oil pressure of each wheel |
| RL Target Oil Pressure | Rear wheel LH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 Mpa |
- | Different according to target oil pressure of each wheel |
| Vehicle Speed | Vehicle speed (estimated vehicle speed used for various controls) | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed Grade | Vehicle acceleration/deceleration | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
Vehicle stopped: 0.000 m/s2During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2 |
During driving: Changes in proportion with vehicle acceleration/deceleration |
| Stop Light SW | Stop light switch assembly (STP terminal input) | OFF / ON | OFF: Brake pedal released
ON: Brake pedal depressed |
|
| Parking Brake SW | Parking brake status | OFF / ON | OFF: Parking brake released
ON: Parking brake applied |
- |
| Stop Light Relay | Stop light control relay (Stop light switch assembly) status (STP terminal input) | OFF / ON | OFF: Stop light control relay (Stop light switch assembly) off and brake pedal released
ON: Stop light control relay (Stop light switch assembly) on or brake pedal depressed |
|
| Inspection Mode | Inspection mode | OFF / ON | OFF: Normal mode
ON: Inspection mode |
- |
| TRC(TRAC) Control | TRC(TRAC) control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| TRC(TRAC) Engine Control | TRC(TRAC) engine control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| TRC(TRAC) Brake Control | TRC(TRAC) brake control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FR Wheel VSC Ctrl Status | Front wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FL Wheel VSC Ctrl Status | Front wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RR Wheel VSC Ctrl Status | Rear wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RL Wheel VSC Ctrl Status | Rear wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FR Wheel ABS Ctrl Status | Front wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FL Wheel ABS Ctrl Status | Front wheel LH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RR Wheel ABS Ctrl Status | Rear wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RL Wheel ABS Ctrl Status | Rear wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| BA Ctrl Status | BA control status | OFF / ON | OFF: During not control
ON: During control |
- |
| PBA Ctrl Status | PBA control status | OFF / ON | OFF: During not control
ON: During control |
- |
| Buzzer | Meter buzzer | OFF / ON | OFF: Buzzer off
ON: Buzzer on |
- |
| Dealer Mode | Dealer Mode (Signal Check mode or Calibration mode) status | OFF / ON | OFF: Normal mode
ON: Dealer Mode (Signal Check mode or Calibration mode) |
|
| Zero Point Memory State of Steering Angle Sensor | Steering sensor zero point memorization status | Zero point is not memorized / Zero point is memorized | - |
|
| Regenerative Cooperation | Regenerative cooperation | OFF / ON | OFF: Not operating
ON: Operating |
- |
| TRC(TRAC)/VSC OFF SW | VSC OFF switch (CSW terminal input) | OFF / ON | OFF: VSC OFF switch OFF
ON: VSC OFF switch ON |
|
| Reservoir Warning SW | Brake fluid level warning switch | OFF / ON | OFF: Reservoir level normal
ON: Reservoir level low |
- |
| ECB Motor Relay | Motor relay operation request | OFF / ON | OFF: Relay off
ON: Relay on |
ECB: Electronically Controlled Brake System |
| ECB Motor Relay2 | Motor relay 2 operation request | OFF / ON | OFF: Relay off
ON: Relay on |
ECB: Electronically Controlled Brake System |
| ECB Solenoid (SGH) | Switching solenoid valve (SGH) | OFF / ON | OFF: Solenoid off
ON: Solenoid on |
ECB: Electronically Controlled Brake System |
| ECB Solenoid (SSA) | Switching solenoid valve (SSA) | OFF / ON | OFF: Solenoid off
ON: Solenoid on |
ECB: Electronically Controlled Brake System |
| MTT | Pump motor operation status | OFF / ON | OFF: Pump motor off
ON: Pump motor on |
- |
| IGP_PT1 | IGP_PT1 status | OFF / ON | OFF: IGP_PT1 off
ON: IGP_PT1 on |
- |
| IGP_PT2 | IGP_PT2 status | OFF / ON | OFF: IGP_PT2 off
ON: IGP_PT2 on |
- |
| FR Wheel | Rotatory direction for front wheel RH | Forward / Back | - | - |
| FL Wheel | Rotatory direction for front wheel LH | Forward / Back | - | - |
| RR Wheel | Rotatory direction for rear wheel RH | Forward / Back | - | - |
| RL Wheel | Rotatory direction for rear wheel LH | Forward / Back | - | - |
| FR Speed Open | Front speed sensor RH open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| FL Speed Open | Front speed sensor LH open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| RR Speed Open | Rear speed sensor RH open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| RL Speed Open | Rear speed sensor LH open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Yaw Rate Open | Yaw rate sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Deceleration Open | Acceleration sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Steering Open | Steering sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Master Cylinder Open | Master cylinder pressure sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| FR Speed Sensor Voltage Open | Front speed sensor RH voltage open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| FL Speed Sensor Voltage Open | Front speed sensor LH voltage open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| RR Speed Sensor Voltage Open | Rear speed sensor RH voltage open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| RL Speed Sensor Voltage Open | Rear speed sensor LH voltage open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Yaw Rate Sensor Voltage Open | Yaw rate sensor voltage open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Air Bag ECU Communication Open | Airbag sensor assembly open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Stroke Open | Brake pedal stroke sensor 1 open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Stroke2 Open | Brake pedal stroke sensor 2 open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Accumulator Open | Accumulator pressure sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| HV Communication Open | Hybrid vehicle communication open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Reaction Force Pressure Sensor Open | Reaction force pressure sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Servo Pressure Sensor Open | Servo pressure sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Reaction Force Pressure | Pressure value of stroke simulator | Min.: 0.00 MPa
Max.: 24.48 MPa |
0.00 to 21.60 MPa | Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal Brake pedal released: 0.00 Mpa |
| Reaction Force Pressure Sensor Temperature | Reaction force pressure sensor temperature | Min.: -80°C (-112°F)
Max.: 175°C (347°F) |
-30°C (-22°F) to 100°C (212°F) | - |
| Stroke Sensor | Brake pedal stroke sensor 1 | Min.: 0.0 V
Max.: 5.0 V |
Brake pedal released: 0.65 to 1.35 V | Reading increases when brake pedal is depressed |
| Stroke Sensor2 | Brake pedal stroke sensor 2 | Min.: 0.0 V
Max.: 5.0 V |
Brake pedal released: 3.6 to 4.35 V | Reading increases when brake pedal is depressed |
| Quantity of Brake Pedal Stroke | Brake pedal stroke amount | Min.: 0 mm
Max.: 255 mm |
Brake pedal released: 0 mm | Reading increases when brake pedal is depressed |
| Servo Pressure | Pressure value of servo | Min.: 0.00 MPa
Max.: 24.48 MPa |
Brake pedal released: 0.00 to 21.60 MPa | Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal |
| Servo Pressure Sensor Temperature | Servo pressure sensor temperature | Min.: -80°C (-112°F)
Max.: 175°C (347°F) |
-30°C (-22°F) to 100°C (212°F) | Current servo pressure sensor temperature |
| Accumulator Pressure | Accumulator pressure output value | Min.: 0.00 MPa
Max.: 24.48 MPa |
15.00 to 21.00 MPa (Pressure stable and pump motor stopped) | When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator |
| Accumulator Pressure Sensor Temperature | Accumulator pressure sensor temperature | Min.: -80°C (-112°F)
Max.: 175°C (347°F) |
-30°C (-22°F) to 100°C (212°F) | - |
| Voltage of Stroke Sensor | Voltage of brake pedal stroke sensor1 | Min.: -2.500 V
Max.: 2.490 V |
- | - |
| Voltage of Stroke Sensor2 | Voltage of brake pedal stroke sensor2 | Min.: -2.500 V
Max.: 2.490 V |
- | - |
| FR Regenerative Request | FR regenerative request torque | Min.: 0 Nm
Max.: 1048560 Nm |
- | Changes according to brake pedal force (When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.) |
| FR Regenerative Operation | FR regenerative operation torque | Min.: 0 Nm
Max.: 1048560 Nm |
- | Changes according to brake pedal force (When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.) |
| Brake Pedal Stroke Change Speed | Brake pedal stroke rate of change | Min.: -2560 mm/s
Max.: 2540 mm/s |
Brake pedal released or depressed and held: 0 mm/s | Brake pedal is being moved: Changes in proportion to the operation speed of the brake pedal |
| Reaction Force Oil Pressure Change Speed | Reaction force pressure rate of change | Min.: -30 MPa/s
Max.: 225 MPa/s |
- | - |
| Target Oil Pressure | Wheel target hydraulic pressure | Min.: 0.00 MPa
Max.: 20.00 Mpa |
- | Changes according to the target wheel cylinder hydraulic pressure |
| VCSK Voltage Value | VCSK voltage value | Min.: 0.000 V
Max.: 5.500 V |
4.800 to 5.200 V | - |
| SLA Solenoid Current | Switching solenoid valve (SLA) current | Min.: 0.000 A
Max.: 1.500 A |
Brake pedal released: 0.000 A | - |
| SLR Solenoid Current | Switching solenoid valve (SLR) current | Min.: 0.000 A
Max.: 1.500 A |
Brake pedal released: 0.000 A | - |
| SGH Solenoid Current | Switching solenoid valve (SGH) current | Min.: 0.000 A
Max.: 3.000 A |
0.00 to 1.50 A | - |
| SSA Solenoid Current | Switching solenoid valve (SSA) current | Min.: 0.000 A
Max.: 3.000 A |
0.00 to 1.50 A | - |
| IGP Voltage | IGP voltage value | 0.000 to 20.000 V | - | Changes in proportion to auxiliary battery voltage |
| IGR Voltage | IGR voltage value | 0.000 to 20.000 V | - | Changes in proportion to auxiliary battery voltage |
| VM1 Voltage | VM1 voltage value | Min.: 0.000 V
Max.: 20.000 V |
- | Changes in proportion to auxiliary battery voltage |
| VM2 Voltage | VM2 voltage value | Min.: 0.000 V
Max.: 20.000 V |
- | Changes in proportion to auxiliary battery voltage |
| BS(linear) Voltage | BS voltage value (for SLA, SLR) | Min.: 0.000 V
Max.: 20.000 V |
- | Changes in proportion to auxiliary battery voltage |
| BS(ABS) Voltage | BS voltage value (for SGH, SSA) | Min.: 0.000 V
Max.: 20.000 V |
- | Changes in proportion to auxiliary battery voltage |
| VCM1 Voltage | VCM1 voltage value | Min.: 0.000 V
Max.: 20.000 V |
6.290 to 7.640 V | - |
| VCM2 Voltage | VCM2 voltage value | Min.: 0.000 V
Max.: 20.000 V |
6.290 to 7.640 V | - |
*1: for performing Dealer Mode (Signal Check): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE
*2: for entering Dealer Mode (Calibration): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY
CLEAR FREEZE FRAME DATA AND INFORMATION
Clearing the DTCs will also clear the Freeze Frame Data.
Clear the DTCs and Freeze Frame Data.