Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0425342 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  Abnormal Noise is Heard from the Engine Compartment when Depressing the Brake Pedal  


DESCRIPTION

Troubleshooting for when abnormal sound occurs from the engine compartment due to air when the brake pedal is depressed.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform "Calibration" after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.PERFORM AIR BLEEDING

B

3.PERFORM AIR BLEEDING
HINT:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>BLEEDING


Result:
Proceed to
NEXT



NEXT

4.RECHECK SYMPTOM
4.RECHECK SYMPTOM
a.

Depress the brake pedal and check if the symptom disappeared.


Result:
Result Proceed to
The symptom disappeared (abnormal sound does not occur). A
The symptom does not disappear (abnormal sound occurs). B



A

5.CLEAR DTC

B

6.PERFORM FORCED ACTUATOR REFRESH
5.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

Result:
Proceed to
NEXT



NEXT

END

6.PERFORM FORCED ACTUATOR REFRESH
a.

Check that the following conditions required to perform "forced actuator refresh" are met and perform "forced actuator refresh" using the GTS.

1.

The shift state indicator shows that the shift lever is in P.

2.

The parking brake is applied.

3.

Vehicle speed is 0 km/h (0 mph).

4.

The brake pedal is not depressed.

5.

The READY light in the combination meter assembly is illuminated (or the ignition switch is ON while the auxiliary battery is being backed up with a power supply).


Chassis > Brake > Utility
Tester Display
Forced Actuator Refresh
50005 435 2618
NOTICE:

As brake fluid pressure is being generated while performing "forced actuator refresh", do not depress the brake pedal or perform a brake system related procedure.


HINT:

While performing "forced actuator refresh", the accumulator pressure may decrease and the meter buzzer may sound.



b.

After "forced actuator refresh" has completed, check the time taken to perform the "forced actuator refresh" displayed on the GTS.

OK:

The time taken to perform "forced actuator refresh" is 10 minutes and 50 seconds or more.


Result:
Proceed to
OK
NG


NOTICE:

If the time taken to perform "forced actuator refresh" is less than 10 minutes and 50 seconds, "forced actuator refresh" may have canceled without completing properly. In this case, check the conditions required to perform "forced actuator refresh" are met and perform "forced actuator refresh" again.




OK

7.RECHECK SYMPTOM

NG

PERFORM FORCED ACTUATOR REFRESH AGAIN

7.RECHECK SYMPTOM
a.

Depress the brake pedal and check if the symptom disappeared.


Result:
Result Proceed to
The symptom disappeared (abnormal sound does not occur). A
The symptom does not disappear (abnormal sound occurs). B



A

8.CLEAR DTC

B

9.PERFORM FORCED ACTUATOR REFRESH
8.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435
HINT:

As DTC C125600 (Accumulator Low Pressure) may be stored by performing "forced actuator refresh", clear the DTCs after performing "forced actuator refresh".



Result:
Proceed to
NEXT



NEXT

END

9.PERFORM FORCED ACTUATOR REFRESH
a.

Check that the following conditions required to perform "forced actuator refresh" are met and perform "forced actuator refresh" using the GTS.

1.

The shift state indicator shows that the shift lever is in P.

2.

The parking brake is applied.

3.

Vehicle speed is 0 km/h (0 mph).

4.

The brake pedal is not depressed.

5.

The READY light in the combination meter assembly is illuminated (or the ignition switch is ON while the auxiliary battery is being backed up with a power supply).


Chassis > Brake > Utility
Tester Display
Forced Actuator Refresh
50005 435 2618
NOTICE:

As brake fluid pressure is being generated while performing "forced actuator refresh", do not depress the brake pedal or perform a brake system related procedure.


HINT:

While performing "forced actuator refresh", the accumulator pressure may decrease and the meter buzzer may sound.



b.

After "forced actuator refresh" has completed, check the time taken to perform the "forced actuator refresh" displayed on the GTS.

OK:

The time taken to perform "forced actuator refresh" is 10 minutes and 50 seconds or more.


Result:
Proceed to
OK
NG


NOTICE:

If the time taken to perform "forced actuator refresh" is less than 10 minutes and 50 seconds, "forced actuator refresh" may have canceled without completing properly. In this case, check the conditions required to perform "forced actuator refresh" are met and perform "forced actuator refresh" again.




OK

10.RECHECK SYMPTOM

NG

PERFORM FORCED ACTUATOR REFRESH AGAIN

10.RECHECK SYMPTOM
a.

Depress the brake pedal and check if the symptom disappeared.


Result:
Result Proceed to
The symptom disappeared (abnormal sound does not occur). A
The symptom does not disappear (abnormal sound occurs). B



A

11.CLEAR DTC

B

12.PERFORM FORCED ACTUATOR REFRESH
11.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435
HINT:

As DTC C125600 (Accumulator Low Pressure) may be stored by performing "forced actuator refresh", clear the DTCs after performing "forced actuator refresh".



Result:
Proceed to
NEXT



NEXT

END

12.PERFORM FORCED ACTUATOR REFRESH
a.

Check that the following conditions required to perform "forced actuator refresh" are met and perform "forced actuator refresh" using the GTS.

1.

The shift state indicator shows that the shift lever is in P.

2.

The parking brake is applied.

3.

Vehicle speed is 0 km/h (0 mph).

4.

The brake pedal is not depressed.

5.

The READY light in the combination meter assembly is illuminated (or the ignition switch is ON while the auxiliary battery is being backed up with a power supply).


Chassis > Brake > Utility
Tester Display
Forced Actuator Refresh
50005 435 2618
NOTICE:

As brake fluid pressure is being generated while performing "forced actuator refresh", do not depress the brake pedal or perform a brake system related procedure.


HINT:

While performing "forced actuator refresh", the accumulator pressure may decrease and the meter buzzer may sound.



b.

After "forced actuator refresh" has completed, check the time taken to perform the "forced actuator refresh" displayed on the GTS.

OK:

The time taken to perform "forced actuator refresh" is 10 minutes and 50 seconds or more.


Result:
Proceed to
OK
NG


NOTICE:

If the time taken to perform "forced actuator refresh" is less than 10 minutes and 50 seconds, "forced actuator refresh" may have canceled without completing properly. In this case, check the conditions required to perform "forced actuator refresh" are met and perform "forced actuator refresh" again.




OK

13.RECHECK SYMPTOM

NG

PERFORM FORCED ACTUATOR REFRESH AGAIN

13.RECHECK SYMPTOM
a.

Depress the brake pedal and check if the symptom disappeared.

Result:
Result Proceed to
The symptom disappeared (abnormal sound does not occur). A
The symptom does not disappear (abnormal sound occurs). B


HINT:

If the symptom does not disappear even after "forced actuator refresh" has completed properly 3 times, replace the brake booster with master cylinder assembly.




A

14.CLEAR DTC

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

14.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435
HINT:

As DTC C125600 (Accumulator Low Pressure) may be stored by performing "forced actuator refresh", clear the DTCs after performing "forced actuator refresh".



Result:
Proceed to
NEXT



NEXT

END