Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0425342 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch (combination switch assembly) turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the "Traction Control Turned Off" will be displayed on the multi-information display and the VSC OFF indicator light will come on.

WIRING DIAGRAM

C397491E22
0.906,0.917 1.521,1.115 0.615,0.198 10 false CANL 0.885,1.729 1.5,1.927 0.615,0.198 10 false CANH 1.396,0.74 1.708,0.938 0.313,0.198 10 false 25 1.385,1.552 1.698,1.75 0.313,0.198 10 false 9 5.073,0.74 5.385,0.938 0.313,0.198 10 false 42 5.073,1.552 5.385,1.75 0.313,0.198 10 false 43 5.354,0.917 5.969,1.115 0.615,0.198 10 false CA1L 5.354,1.729 5.969,1.927 0.615,0.198 10 false CA1H 3.635,2.75 3.792,2.948 0.156,0.198 10 false 5 4.729,2.75 4.885,2.948 0.156,0.198 10 false 7 0.135,3.906 0.594,4.104 0.458,0.198 10 false H6 3.135,3.229 3.594,3.427 0.458,0.198 10 false H18 3.125,3.396 5.094,3.771 1.969,0.375 10 false VSC OFF Switch (Combination Switch Assembly) 3.844,2.76 4,2.958 0.156,0.198 10 false E 4.521,2.76 4.677,2.958 0.156,0.198 10 false + 5.073,2.75 5.385,2.948 0.313,0.198 10 false 18 5.344,2.75 5.802,2.948 0.458,0.198 10 false CSW 6.354,2.865 6.667,3.063 0.313,0.198 10 false IC 4.979,3.896 5.438,4.094 0.458,0.198 10 false A38 4.99,4.052 7.073,4.792 2.083,0.74 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.906,4.344 6.573,4.542 3.667,0.198 10 false : CAN Communication Line 0.146,4.063 4.125,4.26 3.979,0.198 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform "Calibration" after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK IF BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (TRC (TRAC)/VSC OFF Mode)

NG

CONNECT CONNECTOR TO BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CORRECTLY

3.READ VALUE USING GTS (TRC (TRAC)/VSC OFF Mode)
a.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>DATA LIST / ACTIVE TEST

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC(TRAC)/VSC OFF Mode TRC (TRAC)/VSC off mode Normal mode (TRC (TRAC) ON/VSC ON) / TRC(TRAC) OFF mode (TRC (TRAC) OFF/VSC ON) / Not defined / VSC OFF mode (TRC (TRAC) OFF/VSC OFF) Normal mode (TRC (TRAC) ON/VSCON): Normal mode
TRC (TRAC) OFF mode (TRC (TRAC) OFF/VSC ON): TRC off mode
Not defined: Not defined
VSC OFF mode (TRC (TRAC) OFF/VSC OFF): VSC off mode
-
Chassis > Brake > Data List
Tester Display
TRC(TRAC)/VSC OFF Mode
50003 435 45

b.

Check the indicator light and mode condition on the GTS changes according to VSC OFF switch (combination switch assembly) operation.

Standard:
Switch Operation Mode Condition Display Multi-information Display (Traction Control Turned Off) VSC OFF Indicator Light
Not pressed Normal mode (TRC (TRAC) ON/VSC ON) Not displayed Does not come on
Pressing the VSC OFF switch TRC (TRAC) OFF mode (TRC (TRAC) OFF/VSC ON) Displayed Does not come on
Pressing and holding the VSC OFF switch VSC OFF mode (TRC (TRAC) OFF/VSC OFF) Displayed Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display are normal. C



A

4.INSPECT VSC OFF SWITCH

B

C

4.INSPECT VSC OFF SWITCH
a.

Turn the ignition switch off.


b.

Inspect the VSC OFF switch (combination switch assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>INSPECTION

OK:

The VSC OFF switch (combination switch assembly) is normal.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - VSC OFF SWITCH)

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - VSC OFF SWITCH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-18 (CSW) - H18-7 (+) Always Below 1 Ω
A38-18 (CSW) or H18-7 (+) - Body ground Always 10 kΩ or higher
H18-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR