Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0425342 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C05061F  Right Front Wheel Speed Sensor Circuit Intermittent  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake booster with master cylinder assembly). These signals are used for brake control.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake booster with master cylinder assembly).

HINT:

When the connectors between the speed sensor and skid control ECU (brake booster with master cylinder assembly) are connected, the following waveform is output.


C235852E10
1.073,0.865 1.448,0.865 1.448,0.865 1.448,1.073 false 6.458,0.979 6.958,1.146 0.5,0.167 10 false 1.4 V 6.458,1.323 6.969,1.479 0.51,0.156 10 false 0.7 V 0.146,0.771 1.167,1.104 1.021,0.333 10 false Speed Sensor 4.469,1.792 5.396,2.021 0.927,0.229 10 false Low speed 5.375,1.792 6.49,2.104 1.115,0.313 10 false High speed 1.115,2.125 2.74,2.479 1.625,0.354 10 false Speed Sensor Rotor

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C05061F Right Front Wheel Speed Sensor Circuit Intermittent Any of the following is detected:
·

An open in the sensor signal of a malfunctioning wheel occurs 255 times or more.

·

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

·

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Front speed sensor RH

·

Speed sensor installation

·

Wire harness and connector

·

Front speed sensor rotor RH (front axle hub sub-assembly RH)

·

Skid control ECU (brake booster with master cylinder assembly)


Brake

WIRING DIAGRAM

C427730E06
5.74,1.01 6.115,1.24 0.375,0.229 10 false FR+ 1.635,1.135 2.073,1.302 0.438,0.167 10 false FR+ 1.635,1.802 2.073,1.99 0.438,0.188 10 false FR- 5.74,1.698 6.198,1.896 0.458,0.198 10 false FR- 4.917,3 5.417,3.198 0.5,0.198 10 false A38 4.917,3.167 7,3.615 2.083,0.448 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.531,1.021 5.865,1.271 0.333,0.25 10 false 3 5.531,1.708 5.844,2.021 0.313,0.313 10 false 4 2.021,1.688 2.406,1.958 0.385,0.271 10 false 2 2.021,1.021 2.375,1.292 0.354,0.271 10 false 1 0.75,2.417 2.417,2.667 1.667,0.25 10 false Front Speed Sensor RH 0.75,2.25 1.219,2.448 0.469,0.198 10 false A23 0.292,3.365 1.958,3.615 1.667,0.25 10 false *: Shielded 3.76,2.177 5.427,2.427 1.667,0.25 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE

·

After replacing or removing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE



PROCEDURE

1.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Chassis > Brake > Data List
Tester Display
FR Speed Sensor Voltage Open
50003 435 110

b.

Check for any momentary interruptions in the wire harness and connectors.

OK:

Normal (There are no momentary interruptions.)


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FR WHEEL SPEED)

NG

5.CHECK FRONT SPEED SENSOR RH INSTALLATION
2.READ VALUE USING GTS (FR WHEEL SPEED)
a.

Select the Data List on the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
FR Wheel Speed
50003 435 13

b.

Check the front speed sensor RH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

5.CHECK FRONT SPEED SENSOR RH INSTALLATION
3.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
C05061F is not output A
C05061F is output B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.CHECK FRONT SPEED SENSOR RH INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Front Speed Sensor RH
*a Correct
*b Incorrect
*c 8.5 Nm
*d No clearance


Turn the ignition switch off.


b.

Check the front speed sensor RH installation.

OK:

There is no clearance between the front speed sensor RH and steering knuckle.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

6.CHECK FRONT SPEED SENSOR RH AND FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE FRONT SPEED SENSOR RH

6.CHECK FRONT SPEED SENSOR RH AND FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)
a.

Remove the front speed sensor RH and the component with the front speed sensor rotor RH.

for front speed sensor RH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

for front speed sensor rotor RH: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the front speed sensor RH tip and front speed sensor rotor RH.

OK:

No scratches, oil, or foreign matter on the front speed sensor RH tip and front speed sensor rotor RH.


NOTICE:
·

If there is oil or foreign matter on the front speed sensor RH, clean the front speed sensor RH.

·

If the front speed sensor RH is damaged, replace the front speed sensor RH with a new one.

·

Do not use parts cleaner when cleaning the front speed sensor rotor RH.

·

If the front speed sensor rotor RH is damaged, replace the front speed sensor rotor RH with a new one.



HINT:
·

The front speed sensor rotor RH is incorporated into the front axle hub sub-assembly RH.

·

If the front speed sensor rotor RH needs to be replaced, replace it together with the front axle hub sub-assembly RH.




Result:
Proceed to
OK
NG



OK

7.INSPECT HARNESS AND CONNECTOR (FRONT SPEED SENSOR RH - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR RH OR COMPONENT WITH FRONT SPEED SENSOR ROTOR RH

7.INSPECT HARNESS AND CONNECTOR (FRONT SPEED SENSOR RH - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the A23 front speed sensor RH connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A23-1 (FR+) - A38-3 (FR+) Always Below 1 Ω
A23-1 (FR+) or A38-3 (FR+) - Body ground Always 10 kΩ or higher
A23-2 (FR-) - A38-4 (FR-) Always Below 1 Ω
A23-2 (FR-) or A38-4 (FR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)
a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A23-1 (FR+) - Body ground Ignition switch ON 8 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY