Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0425342 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C050C14  Left Rear Wheel Speed Sensor Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC C050C1F.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>C050C1F

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C050C14 Left Rear Wheel Speed Sensor Circuit Short to Ground or Open An open in the speed sensor signal circuit continues for 0.5 seconds or more.
·

Skid control sensor wire LH

·

Rear speed sensor LH (rear axle hub and bearing assembly LH)

·

Wire harness and connector

·

Skid control ECU (brake booster with master cylinder assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE



PROCEDURE

1.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Speed Open Rear speed sensor LH open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Chassis > Brake > Data List
Tester Display
RL Speed Open
50003 435 104

b.

Check for any momentary interruptions in the wire harness and connectors.

OK:

Normal (There are no momentary interruptions.)


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (RL WHEEL SPEED)

NG

5.INSPECT REAR SKID CONTROL SENSOR WIRE LH
2.READ VALUE USING GTS (RL WHEEL SPEED)
a.

Select the Data List on the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
RL Wheel Speed
50003 435 16

b.

Check the rear speed sensor LH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

5.INSPECT REAR SKID CONTROL SENSOR WIRE LH
3.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
C050C14 is not output A
C050C14 is output B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.INSPECT REAR SKID CONTROL SENSOR WIRE LH
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the j1 and Oj1 rear skid control sensor wire LH connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j1-2 (RL+) - Oj1-1 (RL+) Always Below 1 Ω
j1-2 (RL+) or Oj1-1 (RL+) - Body ground and other terminals Always 10 kΩ or higher
j1-1 (RL-) - Oj1-3 (RL-) Always Below 1 Ω
j1-1 (RL-) or Oj1-3 (RL-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (REAR SKID CONTROL SENSOR WIRE LH - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

NG

REPLACE REAR SKID CONTROL SENSOR WIRE LH

6.CHECK HARNESS AND CONNECTOR (REAR SKID CONTROL SENSOR WIRE LH - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Oj1-1 (RL+) - A38-34 (RL+) Always Below 1 Ω
Oj1-1 (RL+) or A38-34 (RL+) -Body ground and other terminals Always 10 kΩ or higher
Oj1-3 (RL-) - A38-35 (RL-) Always Below 1 Ω
Oj1-3 (RL-) or A38-35 (RL-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)
a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the Oj1 rear skid control sensor wire LH connector.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
j1-2 (RL+) - Body ground Ignition switch ON 8 to 14 V


HINT:

The rear speed sensor LH is incorporated into the rear axle hub and bearing assembly LH.

If the rear speed sensor LH needs to be replaced, replace the rear axle hub and bearing assembly LH.



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY