Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0425342 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C05121F  Right Rear Wheel Speed Sensor Circuit Intermittent  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake booster with master cylinder assembly). These signals are used for brake control.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake booster with master cylinder assembly).

HINT:

When the connectors between the speed sensor and skid control ECU (brake booster with master cylinder assembly) are connected, the following waveform is output.


C235852E10
1.073,0.865 1.448,0.865 1.448,0.865 1.448,1.073 false 6.458,0.979 6.958,1.146 0.5,0.167 10 false 1.4 V 6.458,1.323 6.969,1.479 0.51,0.156 10 false 0.7 V 0.146,0.771 1.167,1.104 1.021,0.333 10 false Speed Sensor 4.469,1.792 5.396,2.021 0.927,0.229 10 false Low speed 5.375,1.792 6.49,2.104 1.115,0.313 10 false High speed 1.115,2.125 2.74,2.479 1.625,0.354 10 false Speed Sensor Rotor

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C05121F Right Rear Wheel Speed Sensor Circuit Intermittent Any of the following is detected:
·

An open in the sensor signal of a malfunctioning wheel occurs 255 times or more.

·

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

·

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Skid control sensor wire RH

·

Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

Speed sensor installed improperly

·

Wire harness or connector

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)

·

Skid control ECU (brake booster with master cylinder assembly)


Brake

WIRING DIAGRAM

C436114E01
0.375,2.219 1.875,2.802 1.5,0.583 10 false Rear Speed Sensor RH (Rear Axle Hub and Bearing Assembly RH) 2.052,2.219 3.271,2.656 1.219,0.438 10 false Rear Skid Control Sensor Wire RH 5.083,3 5.542,3.198 0.458,0.198 10 false A38 5.052,3.146 7.156,3.5 2.104,0.354 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 1.323,1.135 1.781,1.333 0.458,0.198 10 false RR+ 2.104,1.146 2.563,1.344 0.458,0.198 10 false RR+ 2.854,1.156 3.313,1.354 0.458,0.198 10 false RR+ 5.281,1.052 5.74,1.25 0.458,0.198 10 false RR+ 1.313,1.813 1.771,2.01 0.458,0.198 10 false RR- 2.083,1.813 2.542,2.01 0.458,0.198 10 false RR- 2.854,1.823 3.313,2.021 0.458,0.198 10 false RR- 5.292,1.708 5.75,1.906 0.458,0.198 10 false RR- 1.781,1.844 2.094,2.042 0.313,0.198 10 false i1 3.229,1.146 3.688,1.344 0.458,0.198 10 false iO1 3.24,1.844 3.698,2.042 0.458,0.198 10 false iO1 1.792,0.938 1.948,1.135 0.156,0.198 10 false 2 1.781,1.635 1.906,1.813 0.125,0.177 10 false 1 3.302,0.948 3.458,1.146 0.156,0.198 10 false 2 3.323,1.635 3.479,1.833 0.156,0.198 10 false 1 5.01,1.031 5.323,1.229 0.313,0.198 10 false 7 5.01,1.719 5.323,1.917 0.313,0.198 10 false 8 4.323,2.271 4.479,2.469 0.156,0.198 10 false * 0.208,3.396 1.896,3.594 1.688,0.198 10 false *: Shielded 1.781,1.146 2.094,1.344 0.313,0.198 10 false i1

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE



PROCEDURE

1.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Chassis > Brake > Data List
Tester Display
RR Speed Sensor Voltage Open
50003 435 112

b.

Check for any momentary interruptions in the wire harness and connectors.

OK:

Normal (There are no momentary interruptions.)


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (RR WHEEL SPEED)

NG

5.CHECK REAR SPEED SENSOR RH INSTALLATION
2.READ VALUE USING GTS (RR WHEEL SPEED)
a.

Select the Data List on the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
RR Wheel Speed
50003 435 15

b.

Check the rear speed sensor RH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

5.CHECK REAR SPEED SENSOR RH INSTALLATION
3.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
C05121F is not output A
C05121F is output B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.CHECK REAR SPEED SENSOR RH INSTALLATION
a.
C210569C19
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 false *a 2.344,1.698 2.656,1.896 0.313,0.198 10 false *b 1.344,0.104 1.656,0.302 0.313,0.198 10 false *c
*a Correct
*b Incorrect
*c No clearance


Turn the ignition switch off.


b.

Check the rear speed sensor RH installation.

OK:

There is no clearance between the rear speed sensor RH and the rear axle hub and bearing assembly RH.


HINT:

The rear speed sensor rotor RH and rear speed sensor RH are incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor rotor RH needs to be replaced, replace the rear axle hub and bearing assembly RH with rear speed sensor RH.



Result:
Proceed to
OK
NG



OK

6.INSPECT REAR SKID CONTROL SENSOR WIRE RH

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

6.INSPECT REAR SKID CONTROL SENSOR WIRE RH
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the i1 and iO1 rear skid control sensor wire RH No. 1 connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-2 (RR+) - iO1-2 (RR+) Always Below 1 Ω
i1-2 (RR+) or iO1-2 (RR+) - Body ground and other terminals Always 10 kΩ or higher
i1-1 (RR-) - iO1-1 (RR-) Always Below 1 Ω
i1-1 (RR-) or iO1-1 (RR-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (REAR SKID CONTROL SENSOR WIRE RH - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

NG

REPLACE REAR SKID CONTROL SENSOR WIRE RH

7.CHECK HARNESS AND CONNECTOR (REAR SKID CONTROL SENSOR WIRE RH - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
iO1-2 (RR+) - A38-7 (RR+) Always Below 1 Ω
iO1-2 (RR+) or A38-7 (RR+) - Body ground Always 10 kΩ or higher
iO1-1 (RR-) - A38-8 (RR-) Always Below 1 Ω
iO1-1 (RR-) or A38-8 (RR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)
a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the iO1 rear skid control sensor wire RH connector.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
i1-2 (RR+) - Body ground Ignition switch ON 8 to 14 V


HINT:

The rear speed sensor RH is incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor RH needs to be replaced, replace the rear axle hub and bearing assembly RH.



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY