Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0425342 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C05262A  Steering Angle Sensor Module Signal Stuck In Range  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) receives signals from the steering sensor via CAN communication.

HINT:

When a malfunction occurs in the communication line to the steering sensor, U012687 is output.

If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.


DTCs may be stored if one of the following occurs:

·

Steering sensor zero point malfunction.

·

Steering sensor signal malfunction.

·

Steering sensor installation abnormality.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C05262A Steering Angle Sensor Module Signal Stuck In Range When communication is normal, a steering sensor malfunction is detected.
·

Steering sensor

·

Wire harness or connector


Brake

WIRING DIAGRAM

C377599E32
0.771,0.635 1.385,0.833 0.615,0.198 10 false CANL 0.75,1.229 1.365,1.427 0.615,0.198 10 false CANH 0.875,1.74 1.49,1.938 0.615,0.198 10 false BAT 0.885,2.406 1.5,2.604 0.615,0.198 10 false IGR 0.844,3.313 1.458,3.51 0.615,0.198 10 false ESS 6.021,0.635 6.635,0.833 0.615,0.198 10 false CA1L 6.031,1.229 6.646,1.427 0.615,0.198 10 false CA1H 3.594,1.729 5.146,2.146 1.552,0.417 10 false from Auxiliary Battery 3.594,2.406 5.24,2.667 1.646,0.26 10 false from IGR-NO. 1 Relay 1.969,1.917 3.104,2.167 1.135,0.25 10 false ECU-DCC NO. 1 1.99,2.604 3.146,2.854 1.156,0.25 10 false ECU-IGR NO. 1 0.344,4.031 0.958,4.229 0.615,0.198 10 false H39 0.344,4.188 1.646,4.5 1.302,0.313 10 false Steering Sensor 5.042,3.906 5.656,4.104 0.615,0.198 10 false A38 5.031,4.073 7.083,4.646 2.052,0.573 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.979,3.542 4.906,3.792 1.927,0.25 10 false : CAN Communication Line 1.271,3.177 1.458,3.417 0.188,0.24 10 false 6 1.271,2.302 1.458,2.542 0.188,0.24 10 false 9 1.271,1.635 1.458,1.875 0.188,0.24 10 false 4 1.271,1.052 1.458,1.292 0.188,0.24 10 false 3 1.281,0.458 1.469,0.698 0.188,0.24 10 false 8 5.781,0.458 5.969,0.698 0.188,0.24 10 false 42 5.781,1.042 5.969,1.281 0.188,0.24 10 false 43

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.RECONFIRM DTC
2.RECONFIRM DTC
a.

Turn the ignition switch to ON and check that no CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING


b.

Turn the ignition switch to ON (READY).


c.

Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left.


d.

Check that no speed sensor and/or yaw rate sensor DTCs are output.

Chassis > Brake > Trouble Codes
50001 435
Result:
Result Proceed to
C05262A is output A
Any CAN communication system DTCs are output B
Speed sensor and/or yaw rate sensor DTCs are output C


HINT:
·

If a speed sensor, or the yaw rate sensor is malfunctioning, DTCs for the steering sensor may be stored even though the steering sensor is normal.

·

If speed sensor and yaw rate sensor DTCs are output simultaneously, repair these malfunctions and then inspect the steering sensor.





A

3.CHECK HARNESS AND CONNECTOR (IGR TERMINAL)

B

C

3.CHECK HARNESS AND CONNECTOR (IGR TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the H39 steering sensor connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H39-9 (IGR) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)
a.

Turn the ignition switch off.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H39-4 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H39-6 (ESS) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR