Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0425342 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C13807E  Stop Lamp Relay Actuator Stuck On  


DESCRIPTION

When any of the following conditions are met, the skid control ECU (brake booster with master cylinder assembly) sets the drive output (STPO) ON which operates the stop light control relay (stop light switch assembly) and turns on the stop lights.

Illumination Conditions:
·

Pre-collision brake is operating.

·

The dynamic radar cruise control system is operating and is applying the brakes.

·

Secondary collision brake is operating.

·

The parking brake is engaged while the vehicle is being driven.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C13807E Stop Lamp Relay Actuator Stuck On When the IGR terminal voltage exceeds 9.5 V and stop light drive output (STPO) is OFF, STP and STP2 ON/OFF signals differ continuously for 5 seconds or more.
·

Wire harness and connector

·

Stop light switch assembly

·

STP circuit

·

STP2 circuit

·

Skid control ECU (brake booster with master cylinder assembly)


Brake

WIRING DIAGRAM

C435754E03
1.063,0.865 4.427,1.063 3.365,0.198 10 false from Auxiliary Battery 4.719,0.521 7.156,0.76 2.438,0.24 10 false to Each Computers 0.969,2.219 3.406,2.458 2.438,0.24 10 false STOP 1.677,1.969 4.115,2.208 2.438,0.24 10 false B 1.49,1.958 1.667,2.156 0.177,0.198 10 false 7 1.677,3.531 4.115,3.771 2.438,0.24 10 false GND 1.5,3.531 1.656,3.74 0.156,0.208 10 false 2 1.635,4.135 4.073,4.375 2.438,0.24 10 false A63 1.625,4.302 4.063,4.542 2.438,0.24 10 false Stop Light Switch Assembly 4.854,4.49 6.313,4.823 1.458,0.333 10 false A38 4.844,4.646 6.906,5.094 2.063,0.448 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.26,5.854 6.313,6.229 2.052,0.375 10 false to Stop Light Circuit 4.854,3.531 5.594,3.792 0.74,0.26 10 false STP 4.594,3.531 4.823,3.76 0.229,0.229 10 false 12 4.583,2.552 4.823,2.771 0.24,0.219 10 false 22 4.854,2.552 5.594,2.813 0.74,0.26 10 false STPO 4.854,1.719 5.594,1.979 0.74,0.26 10 false STP2 4.615,1.635 4.833,1.865 0.219,0.229 10 false 37 3.063,1.625 3.417,1.844 0.354,0.219 10 false L 2.865,2.542 3.219,2.76 0.354,0.219 10 false ACC 2.865,3.542 3.219,3.76 0.354,0.219 10 false OUT 3.26,1.635 3.417,1.844 0.156,0.208 10 false 3 3.26,2.531 3.417,2.74 0.156,0.208 10 false 4 3.26,3.531 3.417,3.74 0.156,0.208 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform calibration (linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration) after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY



PROCEDURE

1.CHECK STOP LIGHT ILLUMINATION STATUS
a.

With the brake pedal released, check the illumination status of the stop lights.


Result:
Result Proceed to
The stop lights are illuminated. A
The stop lights are not illuminated. B



A

2.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

5.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
2.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-12 (STP) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

3.CHECK STOP LIGHT SWITCH ASSEMBLY
3.CHECK STOP LIGHT SWITCH ASSEMBLY
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A63 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-12 (STP) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

4.CHECK FOR SHORT TO +B IN STP CIRCUIT
4.CHECK FOR SHORT TO +B IN STP CIRCUIT
a.

Check that there is no short to +B in the STP circuit (wire harnesses, connectors, stop lights and ECUs).

OK:

No short to +B.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE MALFUNCTIONING PART

5.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-37 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
a.
C401043C89
0.448,0.448 0.781,0.698 0.333,0.25 2.26,1.781 1.854,1.052 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.5,0.49 0.958,0.688 0.458,0.198 10 false A63 2.323,1.708 2.781,1.906 0.458,0.198 10 false L
*a Component with harness connected
(Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A63-3 (L) - Body ground Stop light switch assembly on (Brake pedal depressed) Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

7.CHECK FOR SHORT TO GROUND IN STP2 CIRCUIT
7.CHECK FOR SHORT TO GROUND IN STP2 CIRCUIT
a.

Check that there is no short to ground in the STP2 circuit (wire harnesses, connectors and ECUs)

OK:

There is no short to ground.



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PART