Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0425342 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C126E15  Reservoir Level Switch Circuit Short to Battery or Open  


DESCRIPTION

If the skid control ECU (brake booster with master cylinder assembly) detects that the brake fluid level is low or there is an open in the brake fluid level warning switch signal circuit, DTC C126E15 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C126E15 Reservoir Level Switch Circuit Short to Battery or Open The brake fluid level warning switch (brake booster with master cylinder assembly) circuit is open for 2 seconds or more.
·

Open in brake fluid level warning switch (brake booster with master cylinder assembly)

·

Open in wire harness

·

Skid control ECU (brake booster with master cylinder assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.CHECK BRAKE FLUID LEVEL
a.

Check that the brake fluid level is sufficient.

HINT:

If the fluid level is low, check for fluid leaks, and repair as necessary.


i.

Check for brake fluid leaks (connection between the brake booster pump assembly, brake actuator assembly, brake booster with master cylinder assembly and wheel cylinders).

If no leaks exist, add and adjust fluid using the GTS.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>ON-VEHICLE INSPECTION



Result:
Proceed to
NEXT



NEXT

2.CHECK FOR FLUID LEAK
2.CHECK FOR FLUID LEAK
a.

Check that there are no leaks from the connections between the brake booster pump assembly, brake actuator assembly and brake booster with master cylinder assembly.

HINT:

As a visual check is very difficult, perform the check with the following procedure.


i.

Bleed the air from the brake system.

HINT:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>BLEEDING



ii.

Turn the ignition switch off.


iii.

Disconnect the A27 brake pedal stroke sensor assembly connector.


iv.

Select the Data List on the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MTT Pump motor operation status OFF / ON OFF: Pump motor off
ON: Pump motor on
-
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa, Max.: 24.48 MPa 15.00 to 21.00 MPa
(Pressure stable and pump motor stopped)
When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > Brake > Data List
Tester Display
MTT
Accumulator Pressure
50003 435 100,212

v.

Depress the brake pedal several times to operate the pump motor, then wait until it stops.


vi.

After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.



Result:
Result Proceed to
30 seconds after the pump motor stops the drop in the value of Accumulator Pressure after the pump motor stops is less than 2.50 MPa and pump motor does not operate within 30 seconds A
30 seconds after the pump motor stops the drop in the value of Accumulator Pressure is 2.50 MPa or more or pump motor operates within 30 seconds B



A

3.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH)

B

CHECK AND REPAIR BRAKE FLUID LEAKS OR ADD FLUID

3.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH)
a.
C230719C49
0.854,2.854 1.51,1.99 true 2.604,2.938 1.906,1.979 true 0.177,0.323 0.49,0.521 0.313,0.198 10 false *a 0.708,2.896 1.021,3.094 0.313,0.198 10 false E 2.563,2.969 2.875,3.167 0.313,0.198 10 false +
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Booster with Master Cylinder Assembly))


Turn the ignition switch off.


b.

Reconnect the A27 brake pedal stroke sensor assembly connector.


c.

Remove the brake master cylinder reservoir filler cap assembly.


d.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



e.

Disconnect the A24 brake fluid level warning switch (brake booster with master cylinder assembly) connector.


f.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



g.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the brake master cylinder reservoir assembly (brake booster with master cylinder assembly). Its position changes according to the level of brake fluid.


Standard Resistance:
Tester Connection Condition Specified Condition
1 (+) - 2 (E) Brake fluid level warning switch (brake booster with master cylinder assembly) off (float up) 1.84 to 2.16 kΩ
1 (+) - 2 (E) Brake fluid level warning switch (brake booster with master cylinder assembly) on (float down) Below 1 Ω


HINT:

If there are no problems after completing the preceding inspection, adjust the brake fluid to the MAX level with the ignition switch ON.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-16 (LBL) - A24-1 (+) Always Below 1 Ω
A38-16 (LBL) or A24-1 (+) - Body ground Always 10 kΩ or higher
A24-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK BRAKE DISC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK BRAKE DISC
a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the A24 brake fluid level warning switch (brake booster with master cylinder assembly) connector.


c.

Disconnect the A27 brake pedal stroke sensor assembly connector.


d.

Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.

OK:

Brake pedal does not vibrate during braking.


HINT:
·

An unevenly worn disc may vibrate the caliper pistons and cause fluctuations in brake line pressure, triggering a malfunction detection condition.

·

The brake pedal does not kick back due to caliper piston vibration during electronically controlled brake system control.

·

If the brake pedal stroke sensor assembly connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.

·

The Active Test does not prohibit electronically controlled brake system control when the vehicle is being driven, so disconnect the brake pedal stroke sensor assembly connector before continuing with inspection.

·

Uneven disc wear can be checked by measuring the disc thickness variation.




Result:
Proceed to
OK
NG



OK

6.CLEAR DTC

NG

REPLACE BRAKE DISC

6.CLEAR DTC
a.

Turn the ignition switch off.


b.

Reconnect the A27 brake pedal stroke sensor assembly connector.


c.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

d.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

7.RECONFIRM DTC
7.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
C126E15 is not output A
C126E15 is output B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY