Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0425342 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C134551  Linear Solenoid Valve Offset Learning Not Programmed  C134554  Linear Solenoid Valve Offset Learning Missing Calibration  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) stores the individual characteristics of each linear solenoid built into the brake booster with master cylinder assembly. Based on the stored information, the skid control ECU (brake booster with master cylinder assembly) calibrates the individual differences and controls systems.

The skid control ECU (brake booster with master cylinder assembly) receives the park (P) signal from the hybrid vehicle control ECU through the CAN communication system.

These DTCs are cleared when the linear solenoid valve offset learning results are normal.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C134551 Linear Solenoid Valve Offset Learning Not Programmed The linear solenoid valve offset learning value is not stored. Perform linear solenoid valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal. Brake
C134554 Linear Solenoid Valve Offset Learning Missing Calibration The linear solenoid valve offset learning value cannot be obtained.
·

Perform linear solenoid valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal.

·

Skid control ECU (brake booster with master cylinder assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


HINT:

Before performing linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization, DTC C124A00 will be output.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Check that DTCs other than C134551 and C134554 are not output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
Only C134551 or C134554 is output A
None of the above conditions are met B



A

3.PERFORM AIR BLEEDING

B

3.PERFORM AIR BLEEDING
HINT:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>BLEEDING


Result:
Proceed to
NEXT



NEXT

4.PERFORM LINEAR SOLENOID VALVE OFFSET LEARNING
4.PERFORM LINEAR SOLENOID VALVE OFFSET LEARNING
a.

Turn the ignition switch off.


b.

Check and ensure the following conditions required for performing linear solenoid valve offset learning and then perform linear solenoid valve offset learning.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


Chassis > Brake > Utility
Tester Display
ECB Utility
50005 435 2617
1.

The auxiliary battery voltage is 11 to 15.5 V when the ignition switch ON (READY).

2.

The brake actuator (brake booster with master cylinder assembly) is not hot.

3.

The hybrid control system is not malfunctioning.

4.

The shift state indicator shows that the vehicle shift state is park (P).

5.

The READY light in the combination meter assembly is illuminated.

6.

The brake pedal is not depressed.

7.

The parking brake is released.

8.

DTC C145151 is not output. (If it is output, bleed the air from the high-pressure tube.)



Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
C134551 and C134554 are not output A
C134551 or C134554 is output B



A

END

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY