Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0425342 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C12A512  Left Front Wheel ABS Hold Solenoid Control Circuit Short to Battery  C12A514  Left Front Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open  C12A517  Left Front Wheel ABS Hold Solenoid Control Circuit Voltage Above Threshold  C12A519  Left Front Wheel ABS Hold Solenoid Control Circuit Current Above Threshold  C12A51C  Left Front Wheel ABS Hold Solenoid Control Circuit Voltage Out of Range  C12B012  Left Front Wheel ABS Release Solenoid Control Circuit Short to Battery  C12B014  Left Front Wheel ABS Release Solenoid Control Circuit Short to Ground or Open  C12B019  Left Front Wheel ABS Release Solenoid Control Circuit Current Above Threshold  C12BB12  Right Front Wheel ABS Hold Solenoid Control Circuit Short to Battery  C12BB14  Right Front Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open  C12BB17  Right Front Wheel ABS Hold Solenoid Control Circuit Voltage Above Threshold  C12BB19  Right Front Wheel ABS Hold Solenoid Control Circuit Current Above Threshold  C12BB1C  Right Front Wheel ABS Hold Solenoid Control Circuit Voltage Out of Range  C12C612  Right Front Wheel ABS Release Solenoid Control Circuit Short to Battery  C12C614  Right Front Wheel ABS Release Solenoid Control Circuit Short to Ground or Open  C12C619  Right Front Wheel ABS Release Solenoid Control Circuit Current Above Threshold  C12D112  Left Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery  C12D114  Left Rear Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open  C12D117  Left Rear Wheel ABS Hold Solenoid Control Circuit Voltage Above Threshold  C12D119  Left Rear Wheel ABS Hold Solenoid Control Circuit Current Above Threshold  C12D11C  Left Rear Wheel ABS Hold Solenoid Control Circuit Voltage Out of Range  C12DC12  Left Rear Wheel ABS Release Solenoid Control Circuit Short to Battery  C12DC14  Left Rear Wheel ABS Release Solenoid Control Circuit Short to Ground or Open  C12DC19  Left Rear Wheel ABS Release Solenoid Control Circuit Current Above Threshold  C12E712  Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery  C12E714  Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open  C12E717  Right Rear Wheel ABS Hold Solenoid Control Circuit Voltage Above Threshold  C12E719  Right Rear Wheel ABS Hold Solenoid Control Circuit Current Above Threshold  C12E71C  Right Rear Wheel ABS Hold Solenoid Control Circuit Voltage Out of Range  C12F212  Right Rear Wheel ABS Release Solenoid Control Circuit Short to Battery  C12F214  Right Rear Wheel ABS Release Solenoid Control Circuit Short to Ground or Open  C12F219  Right Rear Wheel ABS Release Solenoid Control Circuit Current Above Threshold  


DESCRIPTION

Each solenoid adjusts the pressure which affects each wheel cylinder according to signals from the skid control ECU (brake booster with master cylinder assembly) and controls the vehicle.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C12A512 Left Front Wheel ABS Hold Solenoid Control Circuit Short to Battery
·

The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more.

·

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12A514 Left Front Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open An open is detected in the solenoid for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12A517 Left Front Wheel ABS Hold Solenoid Control Circuit Voltage Above Threshold A solenoid drive circuit malfunction (flyback diode malfunction) is detected for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12A519 Left Front Wheel ABS Hold Solenoid Control Circuit Current Above Threshold Overcurrent is detected in the solenoid for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12A51C Left Front Wheel ABS Hold Solenoid Control Circuit Voltage Out of Range A malfunction in the solenoid current monitoring circuit is detected for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12B012 Left Front Wheel ABS Release Solenoid Control Circuit Short to Battery Either of the following is detected:
·

The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more.

·

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12B014 Left Front Wheel ABS Release Solenoid Control Circuit Short to Ground or Open An open is detected in the solenoid for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12B019 Left Front Wheel ABS Release Solenoid Control Circuit Current Above Threshold Overcurrent is detected in the solenoid for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12BB12 Right Front Wheel ABS Hold Solenoid Control Circuit Short to Battery Either of the following is detected:
·

The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more.

·

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12BB14 Right Front Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open An open is detected in the solenoid for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12BB17 Right Front Wheel ABS Hold Solenoid Control Circuit Voltage Above Threshold A solenoid drive circuit malfunction (flyback diode malfunction) is detected for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12BB19 Right Front Wheel ABS Hold Solenoid Control Circuit Current Above Threshold Overcurrent is detected in the solenoid for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12BB1C Right Front Wheel ABS Hold Solenoid Control Circuit Voltage Out of Range A malfunction in the solenoid current monitoring circuit is detected for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12C612 Right Front Wheel ABS Release Solenoid Control Circuit Short to Battery Either of the following is detected:
·

The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more.

·

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12C614 Right Front Wheel ABS Release Solenoid Control Circuit Short to Ground or Open An open is detected in the solenoid for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12C619 Right Front Wheel ABS Release Solenoid Control Circuit Current Above Threshold Overcurrent is detected in the solenoid for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12D112 Left Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery Either of the following is detected:
·

The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more.

·

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12D114 Left Rear Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open An open is detected in the solenoid for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12D117 Left Rear Wheel ABS Hold Solenoid Control Circuit Voltage Above Threshold A solenoid drive circuit malfunction (flyback diode malfunction) is detected for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12D119 Left Rear Wheel ABS Hold Solenoid Control Circuit Current Above Threshold Overcurrent is detected in the solenoid for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12D11C Left Rear Wheel ABS Hold Solenoid Control Circuit Voltage Out of Range A malfunction in the solenoid current monitoring circuit is detected for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12DC12 Left Rear Wheel ABS Release Solenoid Control Circuit Short to Battery Either of the following is detected:
·

The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more.

·

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12DC14 Left Rear Wheel ABS Release Solenoid Control Circuit Short to Ground or Open An open is detected in the solenoid for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12DC19 Left Rear Wheel ABS Release Solenoid Control Circuit Current Above Threshold Overcurrent is detected in the solenoid for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12E712 Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery Either of the following is detected:
·

The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more.

·

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12E714 Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open An open is detected in the solenoid for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12E717 Right Rear Wheel ABS Hold Solenoid Control Circuit Voltage Above Threshold A solenoid drive circuit malfunction (flyback diode malfunction) is detected for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12E719 Right Rear Wheel ABS Hold Solenoid Control Circuit Current Above Threshold Overcurrent is detected in the solenoid for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12E71C Right Rear Wheel ABS Hold Solenoid Control Circuit Voltage Out of Range A malfunction in the solenoid current monitoring circuit is detected for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12F212 Right Rear Wheel ABS Release Solenoid Control Circuit Short to Battery Either of the following is detected:
·

The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more.

·

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12F214 Right Rear Wheel ABS Release Solenoid Control Circuit Short to Ground or Open An open is detected in the solenoid for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C12F219 Right Rear Wheel ABS Release Solenoid Control Circuit Current Above Threshold Overcurrent is detected in the solenoid for 0.05 seconds or more.
·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake

WIRING DIAGRAM

C345756E18
4.01,0.917 4.823,1.26 0.813,0.344 10 false ABS-MAIN 2.052,0.771 3.49,1.094 1.438,0.323 10 false from Auxiliary Battery 5.24,0.76 5.844,1.135 0.604,0.375 10 false BS 4.958,0.646 5.563,1.021 0.604,0.375 10 false 52 4.958,1.604 5.563,1.979 0.604,0.375 10 false 14 4.948,2.406 5.552,2.781 0.604,0.375 10 false 48 4.958,3.063 5.563,3.438 0.604,0.375 10 false 49 4.958,3.719 5.563,4.094 0.604,0.375 10 false 50 4.958,4.365 5.563,4.74 0.604,0.375 10 false 51 4.969,5.042 5.573,5.417 0.604,0.375 10 false 44 4.969,5.677 5.573,6.052 0.604,0.375 10 false 45 4.969,6.365 5.573,6.74 0.604,0.375 10 false 46 4.969,7 5.573,7.375 0.604,0.375 10 false 47 4.938,7.854 5.542,8.229 0.604,0.375 10 false A38 4.927,8.021 6.99,8.615 2.063,0.594 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.25,8.073 1.979,8.583 1.729,0.51 10 false Brake Actuator Assembly 1.615,1.615 2.219,1.99 0.604,0.375 10 false 38 1.615,3.719 2.219,4.094 0.604,0.375 10 false 34 1.615,5.052 2.219,5.427 0.604,0.375 10 false 31 6.135,4.771 6.74,5.146 0.604,0.375 10 false IC 5.208,2.417 5.813,2.792 0.604,0.375 10 false SFRH 5.229,1.708 5.833,2.083 0.604,0.375 10 false +BS 5.208,3.063 5.813,3.438 0.604,0.375 10 false SFLH 5.219,3.719 5.823,4.094 0.604,0.375 10 false SRRH 5.219,4.375 5.823,4.75 0.604,0.375 10 false SRLH 5.208,5.042 5.813,5.417 0.604,0.375 10 false SFRR 5.208,5.688 5.813,6.063 0.604,0.375 10 false SFLR 5.208,6.344 5.813,6.719 0.604,0.375 10 false SRRR 5.208,7 5.813,7.375 0.604,0.375 10 false SRLR 1.135,7.01 1.74,7.385 0.604,0.375 10 false SRLR 1.125,6.344 1.729,6.719 0.604,0.375 10 false SRRR 1.146,5.698 1.75,6.073 0.604,0.375 10 false SFLR 1.135,5.052 1.74,5.427 0.604,0.375 10 false SFRR 1.125,4.365 1.729,4.74 0.604,0.375 10 false SRLH 1.125,3.74 1.729,4.115 0.604,0.375 10 false SRRH 1.156,3.073 1.76,3.448 0.604,0.375 10 false SFLH 1.156,2.417 1.76,2.792 0.604,0.375 10 false SFRH 1.219,1.615 1.823,1.99 0.604,0.375 10 false +BS 1.615,6.365 2.219,6.74 0.604,0.375 10 false 28 1.625,4.396 2.229,4.771 0.604,0.375 10 false 11 1.625,5.688 2.229,6.063 0.604,0.375 10 false 2 1.615,7 2.219,7.375 0.604,0.375 10 false 5 1.615,2.417 2.219,2.792 0.604,0.375 10 false 37 1.615,3.063 2.219,3.438 0.604,0.375 10 false 8 0.219,7.906 0.823,8.281 0.604,0.375 10 false A40

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.INSPECT BRAKE ACTUATOR ASSEMBLY
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



C306841C60
4.542,1.063 4.927,0.531 true 3.958,1.052 4.177,0.51 true 3.333,1.052 3.229,0.51 true 2.729,1.052 2.552,0.563 true 1.365,2.135 2.052,1.698 true 2.083,2.25 2.396,1.677 true 2.885,2.323 3.021,1.698 true 4.083,2.323 3.677,1.677 true 4.854,2.26 4.229,1.688 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 4.802,0.375 5.271,0.583 0.469,0.208 10 false SFLR 4.042,0.354 4.448,0.573 0.406,0.219 10 false SRLR 3.094,0.354 3.49,0.552 0.396,0.198 10 false SFLH 2.385,0.385 2.792,0.563 0.406,0.177 10 false SRLH 1.104,2.135 1.417,2.333 0.313,0.198 10 false +BS 1.906,2.281 2.323,2.49 0.417,0.208 10 false SFRH 2.719,2.354 3.167,2.573 0.448,0.219 10 false SRRH 3.948,2.354 4.344,2.552 0.396,0.198 10 false SFRR 4.76,2.281 5.188,2.5 0.427,0.219 10 false SRRR
*a Component without harness connected
(Brake Actuator Assembly)
- -


b.

Disconnect the A40 brake actuator assembly connector.

OK:

No deformation or corrosion.



c.

Measure the resistance according to the value(s) in the table below.

HINT:

Check the brake actuator assembly when it is cooled down.


Standard Resistance:
Tester Connection Condition Specified Condition
38 (+BS) - 37 (SFRH) Always 6.4 to 7.0 Ω
38 (+BS) - 8 (SFLH) Always 6.4 to 7.0 Ω
38 (+BS) - 34 (SRRH) Always 6.4 to 7.0 Ω
38 (+BS) - 11 (SRLH) Always 6.4 to 7.0 Ω
38 (+BS) - 31 (SFRR) Always 5.1 to 5.7 Ω
38 (+BS) - 2 (SFLR) Always 5.1 to 5.7 Ω
38 (+BS) - 28 (SRRR) Always 5.1 to 5.7 Ω
38 (+BS) - 5 (SRLR) Always 5.1 to 5.7 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-14 (+BS) - A40-38 (+BS) Always Below 1 Ω
A38-14 (+BS) or A40-38 (+BS) - Body ground Always 10 kΩ or higher
A38-48 (SFRH) - A40-37 (SFRH) Always Below 1 Ω
A38-48 (SFRH) or A40-37 (SFRH) - Body ground Always 10 kΩ or higher
A38-49 (SFLH) - A40-8 (SFLH) Always Below 1 Ω
A38-49 (SFLH) or A40-8 (SFLH) - Body ground Always 10 kΩ or higher
A38-50 (SRRH) - A40-34 (SRRH) Always Below 1 Ω
A38-50 (SRRH) or A40-34 (SRRH) - Body ground Always 10 kΩ or higher
A38-51 (SRLH) - A40-11 (SRLH) Always Below 1 Ω
A38-51 (SRLH) or A40-11 (SRLH) - Body ground Always 10 kΩ or higher
A38-44 (SFRR) - A40-31 (SFRR) Always Below 1 Ω
A38-44 (SFRR) or A40-31 (SFRR) - Body ground Always 10 kΩ or higher
A38-45 (SFLR) - A40-2 (SFLR) Always Below 1 Ω
A38-45 (SFLR) or A40-2 (SFLR) - Body ground Always 10 kΩ or higher
A38-46 (SRRR) - A40-28 (SRRR) Always Below 1 Ω
A38-46 (SRRR) or A40-28 (SRRR) - Body ground Always 10 kΩ or higher
A38-47 (SRLR) - A40-5 (SRLR) Always Below 1 Ω
A38-47 (SRLR) or A40-5 (SRLR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC
a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the A40 brake actuator assembly connector.


c.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

d.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
C12A512, C12A514, C12A517, C12A519, C12A51C, C12B012, C12B014, C12B019, C12BB12, C12BB14, C12BB17, C12BB19, C12BB1C, C12C612, C12C614, C12C619, C12D112, C12D114, C12D117, C12D119, C12D11C, C12DC12, C12DC14, C12DC19, C12E712, C12E714, C12E717, C12E719, C12E71C, C12F212, C12F214 and C12F219 are not output A
C12A512, C12A514, C12A517, C12A519, C12A51C, C12B012, C12B014, C12B019, C12BB12, C12BB14, C12BB17, C12BB19, C12BB1C, C12C612, C12C614, C12C619, C12D112, C12D114, C12D117, C12D119, C12D11C, C12DC12, C12DC14, C12DC19, C12E712, C12E714, C12E717, C12E719, C12E71C, C12F212, C12F214 or C12F219 is output B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY