Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.03–2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0425342 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C102014  Ignition Switch On/Start Position Circuit Short to Ground or Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C102014 Ignition Switch On/Start Position Circuit Short to Ground or Open All the following conditions are met for 4 seconds or more
·

The IGR terminal voltage is less than 3.5 V and the IGP terminal voltage is 9.5 V or more.

·

Communication with the hybrid vehicle control ECU is normal, or a vehicle speed is 10 km/h (6 mph) or more and the IGR terminal voltage is less than 3.5 V.

·

The IGP terminal voltage is 9.5 V or more.


·

Open or short in IGP circuit

·

Open or short in IGR circuit

·

Improperly connected connector, deformation or corrosion of terminals

·

Skid control ECU (brake booster with master cylinder assembly)


Brake

WIRING DIAGRAM

C343056E16
0.396,0.938 1.448,1.24 1.052,0.302 10 false ABS MTR NO. 1 0.552,2.063 1.604,2.365 1.052,0.302 10 false ABS-MAIN 0.552,3.188 1.604,3.49 1.052,0.302 10 false ABS NO. 2 0.427,4.323 1.479,4.625 1.052,0.302 10 false ECU-IGR NO. 3 0.396,5.458 1.448,5.76 1.052,0.302 10 false ECU-IGP NO. 3 5.979,0.719 6.375,0.958 0.396,0.24 10 false MRI1 5.979,1.865 6.375,2.104 0.396,0.24 10 false BS 5.979,3 6.375,3.24 0.396,0.24 10 false +BI1 5.979,4.125 6.375,4.365 0.396,0.24 10 false IGR 5.979,5.271 6.375,5.51 0.396,0.24 10 false IGP 5.979,6.24 6.448,6.479 0.469,0.24 10 false GND1 5.969,7.083 6.438,7.323 0.469,0.24 10 false GND2 5.719,6.979 5.927,7.167 0.208,0.188 10 false 39 5.719,6.125 5.927,6.313 0.208,0.188 10 false 26 5.781,5.156 5.99,5.344 0.208,0.188 10 false 9 5.719,4.021 5.927,4.208 0.208,0.188 10 false 23 5.719,2.885 5.927,3.073 0.208,0.188 10 false 15 5.708,1.75 5.917,1.938 0.208,0.188 10 false 52 5.771,0.615 5.979,0.802 0.208,0.188 10 false 2 4.74,7.875 5.208,8.115 0.469,0.24 10 false A38 4.729,8.063 7.073,8.635 2.344,0.573 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-23 (IGR) - Body ground Ignition switch ON 11 to 14 V
A38-9 (IGP) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR