Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Front Door) › 2020.03–2020.09
RM36W0E _59 Vehicle Exterior _088018 WINDOW / GLASS _0427203 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:
·

Do not apply positive (+) auxiliary battery voltage to any terminals, except terminal K7-2 (B) or L7-2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION



PROCEDURE

Hide 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.

Connect a positive (+) auxiliary battery lead to connector terminal K7-2 (B).

B572399C02
4.719,0.646 5.073,0.833 0.354,0.188 2.698,1.833 3.365,1.833 true 4.333,1.333 4.75,1.333 true 5,1.333 5.417,1.333 true 5.063,1.646 5.333,1.927 true 4.313,1.917 4.698,1.646 true 3.969,0.552 4.219,0.729 0.25,0.177 10 false *a 3.417,1.75 3.729,1.906 0.313,0.156 10 false *b 4.188,1.26 4.344,1.458 0.156,0.198 10 false B 5.479,1.26 5.896,1.51 0.417,0.25 10 false GND 5.375,1.927 5.875,2.177 0.5,0.25 10 false DOWN 4.167,1.927 4.5,2.177 0.333,0.25 10 false UP 4.813,0.667 5.063,0.844 0.25,0.177 10 false K7
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


NOTICE:

Do not connect a positive (+) auxiliary battery lead to any terminals other than terminal K7-2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a negative (-) auxiliary battery lead to connector terminals K7-1 (GND) and K7-7 (DOWN) or K7-10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) auxiliary battery lead to terminal K7-2 (B), connect a negative (-) auxiliary battery lead to terminal K7-1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals K7-2 (B) and K7-1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal K7-10 (UP).


Motor gear rotates counterclockwise
1.

Connect a positive (+) auxiliary battery lead to terminal K7-2 (B), connect a negative (-) auxiliary battery lead to terminal K7-1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals K7-2 (B) and K7-1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal K7-7 (DOWN).


Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly RH.



Hide 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.

Connect a positive (+) auxiliary battery lead to connector terminal L7-2 (B).

B572400C02
2.385,0.667 2.729,0.854 0.344,0.188 4.146,1.823 4.813,1.823 true 2.667,1.333 3.083,1.333 true 2,1.333 2.417,1.333 true 2.74,1.646 3,2.01 true 2.052,2.01 2.375,1.646 true 1.615,0.521 1.927,0.677 0.313,0.156 10 false *a 3.948,1.75 4.26,1.906 0.313,0.156 10 false *b 3.135,1.26 3.594,1.458 0.458,0.198 10 false GND 1.854,1.26 2.313,1.458 0.458,0.198 10 false B 3.031,2.021 3.583,2.281 0.552,0.26 10 false DOWN 1.917,2.021 2.375,2.219 0.458,0.198 10 false UP 2.479,0.688 2.938,0.885 0.458,0.198 10 false L7
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


NOTICE:

Do not connect a positive (+) auxiliary battery lead to any terminals other than terminal L7-2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a negative (-) auxiliary battery lead to connector terminals L7-1 (GND) and L7-7 (DOWN) or L7-10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect a positive (+) auxiliary battery lead to terminal L7-2 (B), connect a negative (-) auxiliary battery lead to terminal L7-1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals L7-2 (B) and L7-1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal L7-10 (UP).


Motor gear rotates clockwise
1.

Connect a positive (+) auxiliary battery lead to terminal L7-2 (B), connect a negative (-) auxiliary battery lead to terminal L7-1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals L7-2 (B) and L7-1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal L7-7 (DOWN).


Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly LH.