Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB (for TMC Made) › 2020.07–2020.09
RM36W0E _52 Drivetrain _087260 AXLE AND DIFFERENTIAL _0430757 FRONT AXLE HUB(for TMC Made) G

AXLE AND DIFFERENTIAL  FRONT AXLE HUB(for TMC Made)  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front axle hub sub-assembly on-vehicle inspection are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:
for HV Model
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -




HINT:
·

The following procedure is for the LH side.

·

Use the same procedure for the RH side and LH side.



PROCEDURE

Hide 1. PRECAUTION (for HV Model)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISABLE BRAKE CONTROL (for HV Model)

Hide 3.REMOVE FRONT WHEEL

Hide 4.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43512 5.REMOVE FRONT DISC

Hide 6.INSPECT FRONT AXLE HUB BEARING LOOSENESS

a.
C428511

Using a dial indicator with magnetic base, check for looseness near the center of the front axle hub sub-assembly.

Maximum Looseness:

0.05 mm (0.00197 in.)


NOTICE:
·

Ensure that the dial indicator is set perpendicular to the measurement surface.

·

Keep the magnet of the dial indicator away from the front axle hub sub-assembly and front speed sensor.



HINT:

If the looseness exceeds the maximum, replace the front axle hub sub-assembly.



Hide 7.INSPECT FRONT AXLE HUB RUNOUT

a.
C428512

Using a dial indicator with magnetic base, check for runout on the surface of the front axle hub sub-assembly outside the front axle hub bolts.

Maximum Runout:

0.05 mm (0.00197 in.)


NOTICE:
·

Ensure that the dial indicator is set perpendicular to the measurement surface.

·

Make sure to set the tip of the dial indicator towards the outside of the front axle hub bolts.

·

Keep the magnet of the dial indicator away from the front axle hub sub-assembly and front speed sensor.



HINT:

If the runout exceeds the maximum, replace the front axle hub sub-assembly.



Hide 9.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 10.INSTALL FRONT WHEEL

Hide 11.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)

Hide 12. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL (for HV Model)

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART