Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2020.07
RM36W0E _59 Vehicle Exterior _088063 WIPER / WASHER _0420505 WIPER AND WASHER SYSTEM U

WIPER / WASHER  WIPER AND WASHER SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND POWER DISTRIBUTION BOX ASSEMBLY


E445648C01
4.708,4.875 5.208,5.125 0.5,0.25 3.625,0.333 4.083,0.583 0.458,0.25 1.979,1.875 2.417,2.125 0.438,0.25 4.792,3.354 5.208,3.604 0.417,0.25 1.365,3.375 1.802,3.625 0.438,0.25 1.396,4.604 1.833,4.854 0.438,0.25 1.979,1.5 2.417,1.75 0.438,0.25 1.885,0.833 2.219,0.563 true 1.281,0.635 1.635,0.375 true 3.76,0.385 4.073,0.583 0.313,0.198 10 false MB 4.854,4.927 5.167,5.125 0.313,0.198 10 false MB 1.5,3.417 1.813,3.615 0.313,0.198 10 false H4 1.667,0.229 1.979,0.427 0.313,0.198 10 false *1 2.271,0.427 2.583,0.625 0.313,0.198 10 false *2 2.115,1.927 2.427,2.125 0.313,0.198 10 false H4 4.917,3.406 5.229,3.604 0.313,0.198 10 false 4D 0.844,1.698 1.156,1.896 0.313,0.198 10 false 4D 1.521,4.656 1.833,4.854 0.313,0.198 10 false H5 2.115,1.552 2.427,1.75 0.313,0.198 10 false H5
*1 Power Distribution Box Assembly *2 Main Body ECU (Multiplex Network Body ECU)


a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
MB-26 - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
MB-27 - Body ground IG power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
MB-13 - Body ground Ground Always Below 1 Ω


c.

Install the main body ECU (multiplex network body ECU) to power distribution box assembly.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
4D-5 - Body ground CXPI communication line Ignition switch ON Pulse generation
H4-6 (WPS) - Body ground Wiper Relay operation signal Less than approximately 60 seconds after ignition switch turned off 11 to 14 V
Approximately 60 seconds or more after ignition switch turned off Below 1 V
H4-11 (RWRY) - Body ground Rear wiper motor assembly operation signal Rear wiper motor assembly stopped 11 to 14 V
Rear wiper motor assembly operating Below 1 V
H5-11 (LIN4) - Body ground*1 LIN communication line Ignition switch ON Pulse generation

*1: w/ Auto Wiper System




CHECK WINDSHIELD WIPER RELAY ASSEMBLY


E395502N03
2.833,0.25 3.25,0.5 0.417,0.25 3.75,0.25 4.167,0.5 0.417,0.25 2.927,0.292 3.24,0.49 0.313,0.198 10 false A49 3.833,0.292 4.146,0.49 0.313,0.198 10 false A50

a.

Disconnect the A50 and A49 windshield wiper relay assembly connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A50-3 (E) - Body ground Ground Always Below 1 Ω
A50-5 (EWS) - Body ground Ground Always Below 1 Ω
A50-6 (IGWS) - Body ground Washer circuit IG power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
A50-8 (+B) - Body ground Ignition switch ON signal (Power source circuit) Ignition switch ON 11 to 14 V
Less than approximately 60 seconds after ignition switch turned off
Approximately 60 seconds or more after ignition switch turned off Below 1 V
A49-5 (ES) - Body ground Ground Always Below 1 Ω


c.

Connect the A50 and A49 windshield wiper relay assembly connectors.


d.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A50-1 (+WR) - Body ground Front washer operation signal Ignition switch ON, front washer operating 11 to 14 V
A50-2 (+1) - Body ground LO operation signal to windshield wiper motor assembly Ignition switch ON, windshield wiper motor assembly operating in LO 11 to 14 V
A50-4 (+2) - Body ground HI operation signal to windshield wiper motor assembly Ignition switch ON, windshield wiper motor assembly operating in HI 11 to 14 V
A50-7 (-WR) - Body ground Rear washer operation signal Ignition switch ON, rear washer operating 11 to 14 V
A49-3 (2S) - Body ground Windshield wiper motor assembly HI operation signal Windshield wiper motor assembly stopped 4.5 to 5.5 V
Windshield wiper motor assembly operating in HI Below 1 V
A49-4 (MPX1) - Body ground CXPI communication line Ignition switch ON Pulse generation
Less than approximately 100 seconds after ignition switch turned off
Approximately 100 seconds or more after ignition switch turned off 11 to 14 V
A49-6 (+SM) - Body ground Windshield wiper motor assembly position detection signal Windshield wiper motor assembly in LO or HI operation Below 1 V ←→ 11 to 14V
Windshield wiper motor assembly stopped Below 1 V



CHECK RAIN SENSOR (w/ Auto Wiper System)


E379797N14
3.427,0.208 3.771,0.417 0.344,0.208 3.51,0.229 3.823,0.427 0.313,0.198 10 false V9

a.

Disconnect the V9 rain sensor connector.


b.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
V9-2 (ES) - Body ground Ground Always Below 1 Ω
V9-3 (MPX) - Body ground LIN communication signal Ignition switch ON Pulse generation
V9-4 (SIG) - Body ground IG power source circuit Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V