The main body ECU (multiplex network body ECU) and windshield wiper relay assembly communicate via CXPI communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from |
|---|---|---|---|---|---|
| B235787 | Wiper Module Missing Message | Detection condition:
Auxiliary battery voltage is 9.5 V or more Malfunction Status:
Communication malfunction between the main body ECU (multiplex network body ECU) and windshield wiper relay assembly Malfunction Time:
10 seconds or more |
·
Windshield wiper relay assembly ·
Main body ECU (multiplex network body ECU) ·
Harness or connector ·
WIPER relay ·
Power distribution box assembly |
○ | Main Body |
Inspect the fuses of circuits related to this system before performing the following procedure.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1
*1: w/ Entry and Start System
The wiper and washer system uses the CXPI communication system. First, confirm that there is no malfunction in the CXPI communication system.
Pre-procrdure1
Disconnect the A49 windshield wiper relay assembly connector.
Disconnect the 4D power distribution box assembly.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-4 (MPX1) - 4D-5 | Always | Below 1 Ω |
| A49-4 (MPX1) or 4D-5 - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procrdure1
Disconnect the 4D power distribution box assembly connector.
Disconnect the MB main body ECU (multiplex network body ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4D-5 - MB-22 (CXPI) | Always | Below 1 Ω |
| 4D-5 or MB-22 (CXPI) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Pre-procrdure1
Connect the 4D power distribution box assembly connector.
Procedure1
Check for voltage and pulses according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A49-4 (MPX1) - Body ground | Ignition switch ON | Pulse generation |
| A49-4 (MPX1) - Body ground | Ignition switch off | 11 to 14 V |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wiper Power Relay | Function to operate the IG1 wiper relay | OFF or ON | - |
| Tester Display |
|---|
| Wiper Power Relay |
IG1 Wiper relay operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procrdure1
Disconnect the A50 and A49 windshield wiper relay assembly connectors.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A50-3 (E) - Body ground | Always | Below 1 Ω |
| A49-5 (ES) - Body ground | Always | Below 1 Ω |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A50-8 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Less than approximately 60 seconds after ignition switch turned off | 11 to 14 V | |
| Approximately 60 seconds or more after ignition switch turned off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click hereVehicle Exterior>WIPER / WASHER>WIPER ECU (for LHD)>REMOVAL
for RHD: Click hereVehicle Exterior>WIPER / WASHER>WIPER ECU (for RHD)>REMOVAL
NG
OK
NG
| *1 | No. 1 Engine Room Relay Block |
| *a | WIPER Relay Holder |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| WIPER relay holder terminal 3 - Body ground | Ignition OFF | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A50-8 (+B) - WIPER relay holder terminal 5 | Always | Below 1 Ω |
| A50-8 (+B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
OK
NG
Pre-procrdure1
Disconnect the H4 main body ECU (multiplex network body ECU) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| WIPER relay holder terminal 1 - H4-6 (WPS) | Always | Below 1 Ω |
| WIPER relay holder terminal 1 or H4-6 (WPS) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block |
| *a | WIPER Relay Holder |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| WIPER relay holder terminal 2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG