Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2020.07
RM36W0E _59 Vehicle Exterior _088063 WIPER / WASHER _0420505 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B127987  Humidity/Rain Sensor Missing Message  


DESCRIPTION

The main body ECU (multiplex network body ECU) and rain sensor communicate via LIN communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from
B127987 Humidity/Rain Sensor Missing Message
Detection Condition:

Auxiliary battery voltage is 9.5 V or more


Malfunction Status:

Communication malfunction with rain sensor


Malfunction Duration:

10 seconds or more


·

Rain sensor

·

Harness or connector

·

Main body ECU (multiplex network body ECU)


○ Main Body

WIRING DIAGRAM

E377971E12
1.198,0.333 2.885,0.531 1.688,0.198 10 false from IGR-NO. 2 Relay 2.292,1.104 3.979,1.302 1.688,0.198 10 false LIN4 3.698,0.51 5.385,0.708 1.688,0.198 10 false ECU-IGR NO. 2 0.146,1.583 1.833,1.781 1.688,0.198 10 false H5 0.146,1.74 3.208,1.979 3.063,0.24 10 false Main Body ECU (Multiplex Network Body ECU) 0.875,2.375 2.563,2.573 1.688,0.198 10 false : LIN Communication Line 5.469,2.146 6.542,2.344 1.073,0.198 10 false V9 5.479,2.313 6.365,2.521 0.885,0.208 10 false Rain Sensor 5.51,0.354 6.344,0.583 0.833,0.229 10 false SIG 5.5,1.104 6.333,1.333 0.833,0.229 10 false MPX 5.5,1.677 6.333,1.906 0.833,0.229 10 false ES 2.677,0.948 2.875,1.156 0.198,0.208 10 false 11 5.313,0.948 5.51,1.156 0.198,0.208 10 false 3 5.313,0.24 5.51,0.448 0.198,0.208 10 false 4 5.313,1.563 5.51,1.771 0.198,0.208 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1

*1: w/ Entry and Start System




PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - RAIN SENSOR)

Pre-procrdure1

a.

Disconnect the H5 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the V9 rain sensor connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H5-11 (LIN4) - V9-3 (MPX) Always Below 1 Ω



Post-procedure1

d.

None


Result:
Proceed to
OK
NG



OK

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Check for voltage and pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H5-11 (LIN4) - Body ground Ignition switch ON Pulse generation



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - RAIN SENSOR)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - RAIN SENSOR)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V9-4 (SIG) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V9-2 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR