The air conditioning amplifier assembly sends operation signals to the No. 2 semiconductor power integration ECU when quick heater assembly operation conditions are met. Based on the signals from the air conditioning amplifier assembly, the No. 2 semiconductor power integration ECU turn on, and power is supplied to the quick heater assembly installed in the air conditioning radiator assembly.
When all drive conditions are fulfilled, 3 quick heater assembly elements are driven.
The number of quick heater assembly elements driven varies depending on the engine coolant temperature.
If the heating performance is poor when it is cold, the following factors may be the cause.
| Symptom | Factor |
|---|---|
| Heating performance is poor when it is cold | ·
No. 2 semiconductor power integration ECU malfunction ·
Main body ECU (multiplex network body ECU) malfunction ·
Quick heater assembly malfunction ·
Air conditioning amplifier assembly malfunction ·
Harness and connector |
The air conditioning system uses the CAN and CXPI communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the air conditioning system after confirming that the communication systems are functioning properly.
Using the GTS, check if the power integration system is functioning normally.
Click herePower Source / Network>POWER DISTRIBUTION>POWER INTEGRATION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Disconnect the J1 and J2 quick heater assembly connectors.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| PTC Heater | Quick heater assembly | Min.: 0
Max.: 3 |
- |
| Tester Display |
|---|
| PTC Heater |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-1 (B) - Body ground | Perform Active Test and select "OFF" (Control Range 1) | Below 1 V |
| J1-1 (B) - Body ground | Perform Active Test and select "ON" (Control Range 1) | 11 to 14 V |
| J1-3 (B) - Body ground | Perform Active Test and select "OFF" (Control Range 2) | Below 1 V |
| J1-3 (B) - Body ground | Perform Active Test and select "ON" (Control Range 2) | 11 to 14 V |
| J2-2 (B) - Body ground | Perform Active Test and select "OFF" (Control Range 3) | Below 1 V |
| J2-2 (B) - Body ground | Perform Active Test and select "ON" (Control Range 3) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-2 (E) - Body ground | Always | Below 1 Ω |
| J2-1 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Quick Heater Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (B) - A-2 (E) | Always | Below 10 kΩ |
| A-3 (B) - A-2 (E) | Always | Below 10 kΩ |
| A-3 (B) - B-1 (E) | Always | Below 10 kΩ |
| B-2 (B) - B-1 (E) | Always | Below 10 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A88 No. 2 semiconductor power integration ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-1 (B) - A88-1 (L) | Always | Below 1 Ω |
| J1-3 (B) - A88-2 (L) | Always | Below 1 Ω |
| J2-2 (B) - A88-16 (L) | Always | Below 1 Ω |
| J1-1 (B) or A88-1 (L) - Other terminals and body ground | Always | 10 kΩ or higher |
| J1-3 (B) or A88-2 (L) - Other terminals and body ground | Always | 10 kΩ or higher |
| J2-2 (B) or A88-16 (L) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| PTC Heater No.1 Fuse Shut Off Status | Quick heater assembly (PTC1) fuse condition | OFF or ON | OFF: Fuse shut off
ON: Fuse not shut off |
- |
| PTC Heater No.2 Fuse Shut Off Status | Quick heater assembly (PTC2) fuse condition | OFF or ON | OFF: Fuse shut off
ON: Fuse not shut off |
- |
| PTC Heater No.3 Fuse Shut Off Status | Quick heater assembly (PTC3) fuse condition | OFF or ON | OFF: Fuse shut off
ON: Fuse not shut off |
- |
| Tester Display |
|---|
| PTC Heater No.1 Fuse Shut Off Status |
| PTC Heater No.2 Fuse Shut Off Status |
| PTC Heater No.3 Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG