DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Total distance traveled | Min.: 0
Max.: 16777215 |
- | - |
| Total Distance Traveled - Unit | Unit for total distance traveled | km or mile | - | - |
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph) |
Actual vehicle speed | ·
The vehicle speed is detected using the wheel speed sensors. -
There is a delay in when the vehicle speed data is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped. |
| Engine Speed | Engine speed | Min.: 0 rpm
Max.: 16383 rpm |
850 to 950 rpm: Engine idling (shift lever in P, engine warmed up and A/C off) | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Calculate Load | Load calculated by ECM | Min.: 0%
Max.: 100% |
- | ·
This is the engine load calculated based on the estimated intake pressure. ·
Calculate Load = Estimated intake pressure / maximum intake pressure x 100 (%) (For example, when the estimated intake pressure is the same as atmospheric pressure, Calculate Load is 100%.) |
| Coolant Temperature | Coolant temperature | Min.: -40°C (-40°F)
Max.: 140°C (284°F) |
75 to 100°C (167 to 212°F): After warming up |
|
| Intake Air Temperature | Intake air temperature | Min.: -40°C (-40°F)
Max.: 140°C (284°F) |
Equivalent to temperature at location of mass air flow meter sub-assembly |
|
| Ambient Temperature | Ambient temperature | Min.: -40°C (-40°F)
Max.: 215°C (419°F) |
Equivalent to ambient air temperature |
|
| Engine Run Time | Engine run time | Min.: 0 sec.
Max.: 65535 sec. |
Time elapsed since engine started. | This is the time elapsed since the engine was started.
|
| Battery Voltage | Battery voltage | Min.: 0 V
Max.: 65.5 V |
11 to 14 V: Engine idling | If 11 V or less, characteristics of some electrical components may change. |
| Glow Indicator Supported | Glow indicator supported | Unsupp or Supp | - | - |
| Throttle Position Sensor No.1 Voltage % | Absolute throttle position sensor (No. 1) | Min.: 0%
Max.: 100% |
·
10 to 22%: Accelerator pedal fully released ·
64 to 96%: Accelerator pedal fully depressed (engine running) |
The No. 1 throttle position sensor output is converted using 5 V = 100%.
|
| Stop Light SW | Stop light switch assembly status | OFF or ON | ·
OFF: Brake pedal released ·
ON: Brake pedal depressed |
- |
| Complete Parts Monitor | Comprehensive component monitor | Not Avl or Avail | - | ·
*2 |
| Ignition Monitor | Ignition monitor | Spark Ignition or Compression Ignition | - | - |
| Fuel System Monitor | Fuel system monitor | Not Avl or Avail | - | ·
*2 |
| Fuel System Monitor Result | Fuel system monitor | Compl or Incmpl | - | ·
*2 |
| Misfire Monitor | Misfire monitor | Not Avl or Avail | - | ·
*2 |
| EGR/VVT Monitor | EGR/VVT monitor | Not Avl or Avail | - | ·
*2 |
| EGR/VVT Monitor Result | EGR/VVT monitor | Compl or Incmpl | - | ·
*2 |
| A/F (O2) Sensor Heater Monitor | O2S (A/FS) heater monitor | Not Avl or Avail | - | ·
*2 |
| A/F (O2) Sensor Heater Monitor Result | O2S (A/FS) heater monitor | Compl or Incmpl | - | ·
*2 |
| A/F (O2) Sensor Monitor | O2S (A/FS) monitor | Not Avl or Avail | - | ·
*2 |
| A/F (O2) Sensor Monitor Result | O2S (A/FS) monitor | Compl or Incmpl | - | ·
*2 |
| Secondary Air Injection System Monitor | Secondary air injection system monitor | Not Avl or Avail | - | ·
*2 |
| Secondary Air Injection System Monitor Result | Secondary air injection system monitor | Compl or Incmpl | - | ·
*2 |
| EVAP Monitor | EVAP monitor | Not Avl or Avail | - | ·
*2 |
| EVAP Monitor Result | EVAP monitor | Compl or Incmpl | - | ·
*2 |
| Heated Catalyst Monitor | Heated catalyst monitor | Not Avl or Avail | - | ·
*2 |
| Heated Catalyst Monitor Result | Heated catalyst monitor | Compl or Incmpl | - | ·
*2 |
| Catalyst Monitor | Catalyst monitor | Not Avl or Avail | - | ·
*2 |
| Catalyst Monitor Result | Catalyst monitor | Compl or Incmpl | - | ·
*2 |
| TC Terminal | TC terminal status | ON or OFF | OFF | - |
| MIL | MIL status | ON or OFF | OFF | - |
| MIL ON Run Distance | MIL ON run distance | Min.: 0 km (0 mile)
Max.: 65535 km (40723 miles) |
Actual distance driven since DTC detected | - |
| Running Time from MIL ON | Running time from MIL on | Min.: 0 min.
Max.: 65535 min. |
Actual running time since MIL was illuminated | - |
| Time after DTC Cleared | Time after DTC cleared | Min.: 0 min.
Max.: 65535 min. |
Actual time elapsed since DTCs were cleared | This is the time elapsed since DTCs were cleared (or after the vehicle left the factory). Time elapsed when the ignition switch is turned off is not counted. |
| Distance from DTC Cleared | Distance driven after DTCs cleared | Min.: 0 km (0 mile)
Max.: 65535 km (40723 miles) |
Actual distance driven since DTCs cleared | This is the distance driven since DTCs were cleared (or after the vehicle left the factory). |
| Warmup Cycle Cleared DTC | Warmup cycles after DTCs cleared | Min.: 0
Max.: 255 |
- | ·
This is the number of times the engine was warmed up*1 after DTCs were cleared (or after the vehicle left the factory). |
| OBD Requirements | OBD requirement | - | - | - |
| Number of Emission DTC | Emissions-related DTCs stored | Min.: 0
Max.: 127 |
- | - |
| Accel Position from EFI | Accelerator pedal position | Min.: 0%
Max.: 127.5% |
- | Value calculated by adding an adjustment value to the actual accelerator pedal position. |
| NSS Sensor Speed | Secondary pulley speed (NSS) | Min.: 0 rpm
Max.: 65535 rpm |
·
0 rpm: Vehicle stopped and shift lever in D ·
Equal to NO Sensor Speed: Vehicle being driven in belt mode |
- |
| NSS Sensor Voltage | Transmission revolution sensor (NSS) output voltage | Min.: 0.000 V
Max.: 4.999 V |
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) | - |
| NO Sensor Speed | Output shaft speed (NOUT) | Min.: 0 rpm
Max.: 65535 rpm |
·
0 rpm: Vehicle stopped ·
Equal to NSS Sensor Speed: Vehicle being driven in belt mode |
- |
| NO Sensor Voltage | Transmission revolution sensor (NOUT) output voltage | Min.: 0.000 V
Max.: 4.999 V |
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) | - |
| NT Sensor Speed | Input turbine speed (NT) | Min.: 0 rpm
Max.: 65535 rpm |
·
Equal to engine speed (NE): Lock-up ON (After warming up engine) ·
Nearly equal to engine speed (NE): Lock-up OFF (Engine idling with shift lever in P or N) ·
0 rpm: Vehicle stopped with shift lever in R |
- |
| NC1 Sensor Speed | Intermediate shaft (C1 clutch) speed (NC1) | Min.: 0 rpm
Max.: 65535 rpm |
·
0 rpm: Vehicle stopped and synchronizer engaged ·
Equal to NT Sensor Speed: Vehicle being driven in gear mode |
- |
| NC1 Sensor Voltage | Transmission revolution sensor (NC1) output voltage | Min.: 0.000 V
Max.: 4.999 V |
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) | - |
| Belt Clamping Force Sensor | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
·
3.4 to 4.2 MPa (34.7 to 42.8 kgf/cm2, 493 to 609 psi): D position stall test ·
2.4 to 3.2 MPa (24.5 to 32.6 kgf/cm2, 348 to 464 psi): R position stall test |
- |
| Shift SW Status (P Range) | Park/neutral position switch assembly status | OFF or ON | ·
OFF: Shift lever not in P ·
ON: Shift lever in P |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Shift SW Status (R Range) | Park/neutral position switch assembly status | OFF or ON | ·
OFF: Shift lever not in R ·
ON: Shift lever in R |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Shift SW Status (N Range) | Park/neutral position switch assembly status | OFF or ON | ·
OFF: Shift lever not in N ·
ON: Shift lever in N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Shift SW Status (N,P Range) | Park/neutral position switch assembly status | ON or OFF | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Shift SW Status (N,P Range) Supported | Status of park/neutral position switch (N or P) supported | Unsupp or Supp | Supp | - |
| Sport Shift Up SW | Sport shift up switch status*4 | OFF or ON | ·
ON: Shift lever held in "+" or "+" shift paddle switch operated ·
OFF: Shift lever not held in "+" and "+" shift paddle switch released |
- |
| Sport Shift Down SW | Sport shift down switch status*4 | OFF or ON | ·
ON: Shift lever held in "-" or "-" shift paddle switch operated ·
OFF: Shift lever not held in "-" and "-" shift paddle switch released |
- |
| Shift SW Status (S Range) | Transmission control switch status*4 | OFF or ON | ·
ON: Shift lever in M, "+" or "-" ·
OFF: Shift lever not in M, "+" or "-" |
- |
| Shift SW Status (B Range) | Park/neutral position switch assembly status*5 | OFF or ON | ·
OFF: Shift lever not in B ·
ON: Shift lever in B |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Shift SW Status (D Range) | Park/neutral position switch assembly status | OFF or ON | ·
OFF: Shift lever not in D or M*4 ·
ON: Shift lever in D or M*4 |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| A/T Oil Temperature No.1 | CVT fluid temperature sensor value | Min.: -40°C (-40°F)
Max.: 150°C (302°F) |
·
Approximately 100°C (212°F): After stall speed test ·
Equal to ambient temperature: After cold soak |
If the value is -40°C (-40°F) or 150°C (302°F) or more, the CVT fluid temperature sensor circuit is open or shorted. |
| ATF Thermal Degradation Estimate | Estimated value of CVT fluid thermal degradation | Min.: 0
Max.: 65535 |
- | If 50000 or more is displayed, thermal degradation of the CVT fluid is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the CVT fluid. |
| CVT Oil Press Calibration | CVT Oil Pressure Calibration status | Incompl or Compl | Compl | - |
| NT Sensor Voltage | Transmission revolution sensor (NT) output voltage | Min.: 0.000 V
Max.: 4.999 V |
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) | - |
| Synchronize Stroke Sensor Position | Position of synchronizer | Min.: 0.000 mm
Max.: 255.996 mm |
·
0.000 to 1.573 mm (0 to 0.062 in.): Synchronizer not engaged ·
9.139 to 11.798 mm (0.360 to 0.464 in.): Synchronizer engaged |
- |
| Synchronize Stroke Sensor Voltage | Shift stroke sensor voltage | Min.: 0.000 V
Max.: 4.999 V |
·
3.587 to 4.429 V: Synchronizer not engaged ·
0.622 to 1.393 V: Synchronizer engaged |
- |
| Status of Synchronize | Synchronizer status | OFF or ON | ·
OFF: Synchronizer not engaged ·
ON: Synchronizer engaged |
- |
| Lock Up Status | Lock-up | OFF or ON | ·
ON: Lock-up operating ·
OFF: Lock-up not operating |
- |
| CVT Shift Status Ratio | TCM gear ratio command | Min.: 0
Max.: 15.999 |
Same as actual gear ratio | - |
| Shift Mode | Shift mode status | Gear Mode or Belt Mode | - | - |
| Solenoid (SLU) | Shift solenoid valve SLU status | OFF or ON | ·
ON: Shift solenoid valve SLU operating ·
OFF: Shift solenoid valve SLU not operating |
- |
| Solenoid (SLS) High/Low | Shift solenoid valve SLS status | OFF or ON | ·
ON: After engine start ·
OFF: Ignition switch ON |
- |
| Solenoid (SLS) MAX/MIN | Shift solenoid valve SLS status | OFF or ON | ·
ON: After engine start ·
OFF: Ignition switch ON |
- |
| Solenoid (SLP) | Shift solenoid valve SLP status | OFF or ON | ·
ON: Shift solenoid valve SLP operating ·
OFF: Shift solenoid valve SLP not operating |
- |
| Solenoid (SLG) | Shift solenoid valve SLG status | OFF or ON | ·
ON: Shift solenoid valve SLG operating ·
OFF: Shift solenoid valve SLG not operating |
- |
| Solenoid (SL1) | Shift solenoid valve SL1 status | OFF or ON | ·
ON: Shift solenoid valve SL1 operating ·
OFF: Shift solenoid valve SL1 not operating |
- |
| Solenoid (SL2) | Shift solenoid valve SL2 status | OFF or ON | ·
ON: Shift solenoid valve SL2 operating ·
OFF: Shift solenoid valve SL2 not operating |
- |
*1: An engine warmup is defined as the engine coolant temperature rising 20°C (68°F) or more and reaching a temperature of 70°C (158°F) or more after the engine is started.
*2:
Avail: The monitor is available on this vehicle.
Not Avl: The monitor is not available on this vehicle.
Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at sometime in the past. This item does not change when the ignition switch is turned off. However, it will change to Incmpl when DTCs are cleared or the cable is disconnected from the negative (-) battery terminal.
*3: Refer to DTC P070513.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P070513
*4: w/ Shift Paddle Switch
*5: w/o Shift Paddle Switch
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Drive Mode Status | Drive mode status | Normal, Power or ECO | - | - |
| Drive Mode Select Switch | Combination switch assembly (drive mode switch) status | ON or OFF | ·
ON: Combination switch assembly (drive mode switch) being pushed ·
OFF: Combination switch assembly (drive mode switch) not being pushed |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the TC Terminal | ·
Changes to the fluid temperature detection mode ·
Performs stall speed test ·
Performs secondary oil pressure test |
ON or OFF | (Vehicle Condition)
Ignition switch ON, engine stopped and shift lever in P |
| Activate the Lock Up Solenoid | Operates the lock-up | ON or OFF | Can be used to check lock-up operation.
Perform "Activate the Lock Up Solenoid" while monitoring "Engine Speed" and "NT Sensor Speed". (Vehicle Condition)
Vehicle speed: 40 km/h (25 mph) or more |
| Activate the Solenoid (SLU) | Operates the shift solenoid valve SLU | ON or OFF | (Vehicle Condition)
Ignition switch ON, engine stopped and shift lever in P or N |
| Activate the Solenoid (SLS) High/Low | Operates the shift solenoid valve SLS | High or Low | (Vehicle Condition)
Ignition switch ON, engine stopped and shift lever in P or N |
| Activate the Solenoid (SLS) MAX/MIN | Operates the shift solenoid valve SLS | MIN or MAX | (Vehicle Condition)
Ignition switch ON, engine stopped and shift lever in P or N |
| Activate the Solenoid (SLP) | Operates the shift solenoid valve SLP | ON or OFF | (Vehicle Condition)
Ignition switch ON, engine stopped and shift lever in P or N |
| Active the Synchronize | Operates the synchronizer | ON or OFF |
(Vehicle Condition)
Ignition switch ON, engine running, stop light switch assembly ON, shift lever in P and CVT fluid temperature between 20°C (68°F) and 100°C (212°F) |
| Control the Shift Mode | Changes the shift mode | GEAR: Gear Mode
LOW: Belt Mode (Low) MIDDLE: Belt Mode (Middle) HIGH: Belt Mode (High) |
(Vehicle Condition)
Vehicle speed between 20 km/h (12 mph) and 45 km/h (28 mph) and CVT fluid temperature -20°C (-4°F) or more |
| Activate the Solenoid (SLG) | Operates the shift solenoid valve SLG | ON or OFF | (Vehicle Condition)
Ignition switch ON, engine stopped and shift lever in P or N |
| Activate the Solenoid (SL1) | Operates the shift solenoid valve SL1 | ON or OFF | (Vehicle Condition)
Ignition switch ON, engine stopped and shift lever in P or N |
| Activate the Solenoid (SL2) | Operates the shift solenoid valve SL2 | ON or OFF | (Vehicle Condition)
Ignition switch ON, engine stopped and shift lever in P or N |