Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _087499 M15A-FKS ENGINE CONTROL _0418534 SFI SYSTEM U

M15A-FKS ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


A458815E01
1.781,0.156 2.198,0.458 0.417,0.302 5.385,0.188 5.802,0.49 0.417,0.302 1.875,0.229 2.385,0.448 0.51,0.219 11 false D51 5.479,0.26 5.99,0.479 0.51,0.219 11 false A54

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals are shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
A54-1 (BATT) - A54-10 (E1) Battery (for measuring battery voltage and ECM memory) Always 11 to 14 V
A54-2 (IGP) - A54-10 (E1) Ignition switch signal Ignition switch ON 11 to 14 V
A54-6 (FPC) - A54-10 (E1) Fuel pump control Ignition switch ON Below 1.5 V
A54-7 (CANP)*1 - A54-10 (E1) CAN communication line Engine stopped, ignition switch ON Pulse generation
(See waveform 1)
A54-8 (CANH) - A54-10 (E1) CAN communication line Engine stopped, ignition switch ON Pulse generation
(See waveform 1)
A54-9 (+B) - A54-10 (E1)
·

Power source of ECM

·

Power source of throttle actuator


Ignition switch ON 11 to 14 V
A54-10 (E1) - Body ground Ground Always Below 1 Ω
A54-11 (ELS2) - A54-10 (E1) Current consumer signal Rear defogger ON 11 to 14 V
A54-13 (IGR) - A54-10 (E1) Ignition signal Ignition switch ON 11 to 14 V
A54-15 (MREL) - A54-10 (E1) EFI-MAIN NO. 1 relay operation signal Ignition switch ON Below 1.5 V
A54-16 (NEO) - A54-10 (E1) Engine speed signal sent to other ECUs Idling with warm engine Pulse generation
(See waveform 2)
A54-17 (CANN)*1 - A54-10 (E1) CAN communication line Engine stopped, ignition switch ON Pulse generation
(See waveform 3)
A54-18 (CANL) - A54-10 (E1) CAN communication line Engine stopped, ignition switch ON Pulse generation
(See waveform 3)
A54-21 (STP) - A54-10 (E1) Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released 0 to 1.5 V
A54-22 (ST1-) - A54-10 (E1) Stop light switch assembly signal
(opposite to STP terminal)
Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A54-23 (NSW) - A54-10 (E1) Park/Neutral position switch assembly signal*1 Ignition switch ON, shift lever not in P or N 11 to 14 V
Ignition switch ON, shift lever in P or N Below 3.0 V
Clutch start switch signal*2 Ignition switch ON, clutch pedal fully released 11 to 14 V
Ignition switch ON, clutch pedal depressed Below 3.0 V
A54-30 (STA) - A54-10 (E1) Starter assembly signal Cranking 6.0 V or higher
A54-32 (RFC) - A54-10 (E1) Cooling fan control signal Ignition switch ON, A/C switch on (max cool) Pulse generation
(See waveform 4)
A54-34 (IREL) - A54-10 (E1) D INJ relay operation signal Ignition switch ON Below 1.5 V
A54-35 (+B2) - A54-10 (E1) Power source of ECM Ignition switch ON 11 to 14 V
A54-36 (E01) - Body ground Ground Always Below 1 Ω
A54-39 (KSW) - A54-10 (E1) Key in vehicle signal Key outside vehicle 11 to 14 V
A54-42 (SPD) - A54-10 (E1) Vehicle speed signal from combination meter assembly Driving at 20 km/h (12 mph) Pulse generation
(See waveform 5)
A54-45 (EC) - Body ground Ground Always Below 1 Ω
A54-53 (+BD1) - A54-10 (E1) Power source of ECU (injector driver) Ignition switch ON 11 to 14 V
A54-54 (E1D1) - Body ground Ground Always Below 1 Ω
A54-55 (VPA) - A54-56 (EPA) Accelerator pedal position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 2.6 to 4.5 V
A54-57 (VCPA) - A54-56 (EPA) Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
A54-58 (VPA2) - A54-59 (EPA2) Accelerator pedal position sensor signal Ignition switch ON, accelerator pedal fully released 1.2 to 2.0 V
Ignition switch ON, accelerator pedal fully depressed 3.4 to 4.75 V
A54-60 (VCP2) - A54-59 (EPA2) Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
D51-1 (M-) - A54-10 (E1) Throttle actuator operation signal (negative signal) Idling with warm engine Pulse generation
(See waveform 6)
D51-2 (M+) - A54-10 (E1) Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(See waveform 7)
D51-3 (EGA+) - A54-10 (E1) EGR valve assembly operation signal Idling with warm engine Pulse generation
(See waveform 8)
D51-4 (EGA-) - A54-10 (E1) EGR valve assembly operation signal Idling with warm engine Pulse generation
(See waveform 8)
D51-5 (EGB-) - A54-10 (E1) EGR valve assembly operation signal Idling with warm engine Pulse generation
(See waveform 8)
D51-6 (EGB+) - A54-10 (E1) EGR valve assembly operation signal Idling with warm engine Pulse generation
(See waveform 8)
D51-7 (HTHM) - A54-10 (E1) Thermostat heater (water inlet with thermostat sub-assembly) operation signal Ignition switch ON 11 to 14 V
D51-8 (HA1B) - A54-10 (E1) Air fuel ratio sensor (sensor 2) heater operation signal Ignition switch ON 11 to 14 V
Idling with cold engine Pulse generation
(See waveform 9)
D51-9 (HA1A) - A54-10 (E1) Air fuel ratio sensor (sensor 1) heater operation signal Ignition switch ON 11 to 14 V
Idling with cold engine Pulse generation
(See waveform 9)
D51-11 (#2D+) - A54-10 (E1) Fuel injector assembly signal (No. 2 cylinder) Idling with warm engine. Pulse generation
(See waveform 10)
D51-10 (#2D-) - A54-10 (E1) Fuel injector assembly signal (No. 2 cylinder) Idling with warm engine. Pulse generation
(See waveform 10)
D51-13 (#3D+) - A54-10 (E1) Fuel injector assembly signal (No. 3 cylinder) Idling with warm engine. Pulse generation
(See waveform 10)
D51-14 (#3D-) - A54-10 (E1) Fuel injector assembly signal (No. 3 cylinder) Idling with warm engine. Pulse generation
(See waveform 10)
D51-16 (#1D+) - A54-10 (E1) Fuel injector assembly signal (No. 1 cylinder) Idling with warm engine. Pulse generation
(See waveform 10)
D51-17 (#1D-) - A54-10 (E1) Fuel injector assembly signal (No. 1 cylinder) Idling with warm engine. Pulse generation
(See waveform 10)
D51-19 (FP1+) - A54-10 (E1) Fuel pump assembly (for high pressure side) signal Idling with warm engine. Pulse generation
(See waveform 11)
D51-18 (FP1-) - A54-10 (E1) Fuel pump assembly (for high pressure side) signal Idling with warm engine. Pulse generation
(See waveform 11)
D51-25 (OE1+) - D51-24 (OE1-) Cam timing oil control solenoid assembly operation signal (for exhaust side) Idling Pulse generation
(See waveform 12)
D51-27 (OC1+) - D51-26 (OC1-) Cam timing oil control solenoid assembly operation signal (for intake side) Idling Pulse generation
(See waveform 12)
D51-43 (PRG) - A54-10 (E1) Purge VSV operation signal Ignition switch ON 11 to 14 V
Idling with warm engine, under purge control Pulse generation
(See waveform 13)
D51-45 (D) - A54-10 (E1) Clutch switch signal Clutch switch ON
(Clutch pedal depressed)
11 to 14 V
Clutch switch OFF
(Clutch pedal released)
Below 1.0 V
D51-47 (IGT3) - A54-10 (E1) No. 3 ignition coil assembly signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 14)
D51-48 (IGT2) - A54-10 (E1) No. 2 ignition coil assembly signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 14)
D51-49 (IGT1) - A54-10 (E1) No. 1 ignition coil assembly signal
(ignition signal)
Idling with warm engine Pulse generation
(See waveform 14)
D51-50 (WPO) - A54-10 (E1) Electric water pump assembly signal Idling with warm engine Pulse generation
(See waveform 15)
D51-51 (WPI) - A54-10 (E1) Electric water pump assembly signal Idling with warm engine Pulse generation
(See waveform 16)
D51-63 (LIN) - A54-10 (E1) LIN communication line Ignition switch ON Pulse generation
(See waveform 17)
D51-68 (R) - A54-10 (E1) Reverse signal Ignition switch ON, shift lever in R 11 to 14 V
D51-78 (VCVG) - A54-10 (E1) Power source of mass air flow meter sub-assembly (specific voltage) Ignition switch ON 4.8 to 5.2 V
D51-82 (VCPX)*3 - D51-59 (EPEX)*3 Power source of differential pressure sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D51-83 (VCNP)*2 - A54-10 (E1) Power source of neutral position switch (specific voltage) Ignition switch ON 4.5 to 5.5 V
D51-84 (VCPF) - A54-10 (E1) Power source of fuel pressure sensor (for low pressure side) (specific voltage) Ignition switch ON 4.75 to 5.25 V
D51-87 (VTA2) - D51-110 (ETA) Throttle position sensor signal (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 2.1 to 3.1 V
Accelerator pedal fully depressed (engine running) 4.6 to 5.0 V
D51-88 (VCV1) - A54-10 (E1) Power source of camshaft position sensor (for intake camshaft) (specific voltage) Ignition switch ON 4.5 to 5.5 V
D51-90 (VV1+) - D51-89 (VV1-) Camshaft position sensor (for intake camshaft) signal Idling with warm engine Pulse generation
(See waveform 18)
D51-91 (EV1+) - D51-114 (EV1-) Camshaft position sensor (for exhaust camshaft) signal Idling with warm engine Pulse generation
(See waveform 18)
D51-92 (NE+) - D51-115 (NE-) Crankshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 19)
D51-93 (VS+) - A54-10 (E1) Air fuel ratio sensor (sensor 1) signal Engine stopped, ignition switch ON 4.1 to 5.0 V
D51-94 (COM) - A54-10 (E1) Air fuel ratio sensor (sensor 1) signal Engine stopped, ignition switch ON 2.4 to 2.6 V
D51-95 (IP+) - A54-10 (E1) Air fuel ratio sensor (sensor 1) signal Engine stopped, ignition switch ON 2.4 to 2.6 V
D51-97 (PR) - D51-96 (EPR) Fuel pressure sensor (for high pressure side) signal Idling with warm engine 0.5 to 4.5 V
D51-98 (VCPR) - D51-96 (EPR) Power source of fuel pressure sensor (for high pressure side) (specific voltage) Ignition switch ON 4.75 to 5.25 V
D51-99 (VCPE) - D51-100 (EPEO) Power source of engine oil pressure and temperature sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D51-101 (VG) - D51-79 (E2G) Mass air flow meter sub-assembly signal Ignition switch ON Pulse generation
(See waveform 20)
D51-102 (THA) - D51-79 (E2G) Intake air temperature sensor (mass air flow meter sub-assembly) signal Idling, intake air temperature 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
D51-105 (PEX)*3 - D51-59 (EPEX)*3 Differential pressure sensor signal Ignition switch ON 0.4 to 4.8 V
D51-106 (NPSW)*2 - D51-60 (ENPS) Neutral position switch signal Ignition switch ON, shift lever in N 2.7 to 4.3 V
Ignition switch ON, shift lever in except N 0.7 to 1.9 V
D51-107 (PFL) - D51-61 (EPFL) Fuel pressure sensor (for low pressure side) signal Idling with warm engine 0.57 to 4.88 V
D51-108 (VTA1) - D51-110 (ETA) Throttle position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.6 to 1.1 V
Accelerator pedal fully depressed (engine running) 3.2 to 4.8 V
D51-109 (VCTA) - D51-110 (ETA) Power source of throttle position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D51-111 (KNK1) - D51-112 (EKNK) Knock control sensor signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 21)
D51-113 (VCE1) - A54-10 (E1) Power source of camshaft position sensor (for exhaust camshaft) (specific voltage) Ignition switch ON 4.5 to 5.5 V
D51-116 (VCNE) - A54-10 (E1) Power source of crankshaft position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D51-117 (A1B-) - A54-10 (E1) Air fuel ratio sensor (sensor 2) signal Ignition switch ON 1.17 to 4.49 V
D51-118 (A1B+) - A54-10 (E1) Air fuel ratio sensor (sensor 2) signal Ignition switch ON 1.53 to 5.96 V
D51-120 (PIM) - D51-119 (EPIM) Manifold absolute pressure sensor signal Ignition switch ON 3.0 to 4.5 V
D51-121 (VCPM) - D51-119 (EPIM) Power source of manifold absolute pressure sensor (specific voltage) Ignition switch ON 4.75 to 5.25 V
D51-122 (PEO) - D51-100 (EPEO) Engine oil pressure sensor (engine oil pressure and temperature sensor) signal Idling with warm engine 0.5 to 4.5 V
D51-123 (THEO) - D51-100 (EPEO) Engine oil temperature sensor (engine oil pressure and temperature sensor) signal Ignition switch ON 0.54 to 4.86 V
D51-125 (THW) - D51-124 (ETHW) Engine coolant temperature sensor signal Idling, engine coolant temperature 75 to 100°C (167 to 212°F) 0.2 to 1.0 V

*1: for continuously variable transaxle models

*2: for manual transaxle models

*3: w/ Gasoline particulate filter

WAVEFORM 1


A283576E15
3.01,1.396 3.344,1.708 0.333,0.313 10 false GND

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Between CANP and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 2


A431371E03
2.833,0.938 3.292,1.135 0.458,0.198 10 false GND

Engine Speed Signal
ECM Terminal Name Between NEO and E1
Tester Range 5 V/DIV., 2 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 3


A283577E13
3.01,1.365 3.375,1.604 0.365,0.24 10 false GND

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Between CANN and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 4


A282867E26
2.76,1.563 3.115,1.792 0.354,0.229 10 false GND

Cooling Fan Control Signal
ECM Terminal Name Between RFC and E1
Tester Range 1 V/DIV., 20 ms/DIV.
Condition Ignition switch ON, A/C switch on (max cool)

HINT:

The duty ratio varies depending on the engine coolant temperature.



WAVEFORM 5


A283573E22
2.833,1.229 3.25,1.531 0.417,0.302 10 false GND

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 6


A245848E79
2.854,1 3.323,1.354 0.469,0.354 10 false GND 0.479,0.625 0.844,0.875 0.365,0.25 10 false M-

Throttle Actuator Operation Signal (Negative Terminal)
ECM Terminal Name Between M- and E1
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 7


A208000E84
2.854,0.99 3.313,1.302 0.458,0.313 10 false GND 0.521,0.656 0.99,0.948 0.469,0.292 10 false M+

Throttle Actuator Operation Signal (Positive Terminal)
ECM Terminal Name Between M+ and E1
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 8


A405745E09
0.198,0.313 0.813,0.667 0.615,0.354 10 false EGA+ 0.229,1.365 0.844,1.719 0.615,0.354 10 false EGA- 2.74,0.792 3.354,1.146 0.615,0.354 10 false GND 2.75,1.594 3.365,1.948 0.615,0.354 10 false GND 0.167,0.458 0.781,0.813 0.615,0.354 10 false (EGB+) 0.198,1.51 0.813,1.865 0.615,0.354 10 false (EGB-)

EGR Valve Assembly Operation Signal
ECM Terminal Name CH1: Between EGA+ and E1
CH2: Between EGA- and E1
CH1: Between EGB+ and E1
CH2: Between EGB- and E1
Tester Range 5 V/DIV., 5 μs./DIV.
Condition Idling with warm engine

HINT:

When the EGR valve assembly is operating, a waveform is produced at each terminal.



WAVEFORM 9


A205412E44
2.688,0.896 3.104,1.24 0.417,0.344 10 false GND

Air Fuel Ratio Sensor Heater Operation Signal
ECM Terminal Name Between HA1A and E1
Between HA1B and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with cold engine


WAVEFORM 10


A405747E04
0.302,0.573 0.76,0.771 0.458,0.198 10 false CH1 0.313,0.938 0.771,1.135 0.458,0.198 10 false CH2 2.781,0.594 3.24,0.792 0.458,0.198 10 false GND 2.771,0.948 3.229,1.146 0.458,0.198 10 false GND

No. 1 (to No. 3) Fuel Injector Assembly Signal
ECM Terminal Name CH1: Between #1D+ and E1
CH2: Between #1D- and E1
CH1: Between #2D+ and E1
CH2: Between #2D- and E1
CH1: Between #3D+ and E1
CH2: Between #3D- and E1
Tester Range 50 V/DIV., 200 μs./DIV.
Condition Idling with warm engine.


WAVEFORM 11


A405748E08
0.26,0.406 1.573,0.698 1.313,0.292 10 false FP1+ 0.271,1.083 1.583,1.375 1.313,0.292 10 false FP1- 2.76,0.438 3.135,0.865 0.375,0.427 10 false GND 2.76,1.104 3.135,1.531 0.375,0.427 10 false GND

Fuel Pump Assembly (for High Pressure Side) Signal
ECM Terminal Name CH1: Between FP1+ and E1
CH2: Between FP1- and E1
Tester Range 20 V/DIV., 500 μs./DIV.
Condition Idling with warm engine.


WAVEFORM 12


A283575E01
0.604,0.26 1.563,0.573 0.958,0.313 10 5 V/DIV. 0.51,1.125 1.021,1.385 0.51,0.26 10 GND 1.729,1.844 2.583,2.063 0.854,0.219 10 1 ms./DIV.

Cam Timing Oil Control Solenoid Assembly Operation Signal
ECM Terminal Name Between OC1+ and OC1-
Between OE1+ and OE1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 13


A218020E40
2.802,0.938 3.292,1.26 0.49,0.323 10 false GND

Purge VSV Operation Signal
ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling with warm engine, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 14


A458860E01
2.948,0.99 3.406,1.188 0.458,0.198 10 false GND

Ignition Coil Assembly Signal (IGT Signal)
ECM Terminal Name Between IGT (1 to 3) and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 15


A214025E42
2.99,1.792 3.323,1.948 0.333,0.156 10 false GND

Engine Water Pump Assembly Signal (from ECM to Engine Water Pump Assembly)
ECM Terminal Name Between WPO and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the engine water pump assembly speed.



WAVEFORM 16


A214025E43
2.99,1.792 3.323,1.948 0.333,0.156 10 false GND

Engine Water Pump Assembly Signal (from Engine Water Pump Assembly to ECM)
ECM Terminal Name Between WPI and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine water pump assembly speed increases.



WAVEFORM 17


A349005E05
2.927,1.906 3.281,2.115 0.354,0.208 10 false GND

LIN Communication Signal (Reference)
ECM Terminal Name Between LIN and E1
Tester Range 2 V/DIV., 10 ms./DIV.
Condition Idling with warm engine


WAVEFORM 18


A368769E04
2.875,0.844 3.333,1.042 0.458,0.198 10 false GND 2.875,1.563 3.333,1.76 0.458,0.198 10 false GND

Camshaft Position Sensor Signal
ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 19


A200774E37
2.969,1.177 3.396,1.438 0.427,0.26 10 false GND

Crankshaft Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 20


A337204E17
0.115,1.417 0.469,1.615 0.354,0.198 10 false GND

Mass Air Flow Meter Sub-assembly Signal
ECM Terminal Name Between VG and E2G
Tester Range 1 V/DIV., 100 μs./DIV.
Condition Ignition switch ON


WAVEFORM 21


A283572E35
2.615,1 3.115,1.292 0.5,0.292 10 false GND

Knock Control Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle.