Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for M15A-FKS TMC Made) › from 2020.07
RM36W0E _52 Drivetrain _087547 DRIVE SHAFT / PROPELLER SHAFT _0430978 FRONT DRIVE SHAFT ASSEMBLY(for M15A-FKS TMC Made) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for M15A-FKS TMC Made)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43448G 1.SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP (for CVT)

a.
C411286

Using pliers, separate the front No. 2 axle inboard joint boot clamp as shown in the illustration.


Hide 43448G 2.SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP (for Manual Transaxle)

a.
C205158

Using a screwdriver, separate the front No. 2 axle inboard joint boot clamp as shown in the illustration.


Hide 43448F 3.SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP

a.
C435699

Using a screwdriver, separate the front axle inboard joint boot clamp as shown in the illustration.


Hide 4.SEPARATE FRONT AXLE INBOARD JOINT BOOT

a.

Separate the front axle inboard joint boot from the front drive inboard joint assembly.


Hide 43040 5.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY (for CVT)

a.

Remove the old grease from the front drive inboard joint assembly.


b.
C374772C01
1.74,0.896 1.198,0.292 1.198,0.292 2.042,0.521 false 1,0.167 1.313,0.365 0.313,0.198 10 false *a
*a Matchmark


Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.

NOTICE:

Do not use a punch for the marks.



c.

Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.


d.
C392790

Using a snap ring expander, remove the shaft snap ring from the front drive outboard joint shaft assembly.


e.
C141145C17
2.854,1.073 1.844,1.479 1.844,1.479 2.885,1.135 true 1.646,1.427 1.833,1.583 0.188,0.156 10 *a
*a Matchmark


Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.

NOTICE:

Do not use a punch for the marks.



f.

Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Do not drop the tripod joint.




Hide 43040 6.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY (for Manual Transaxle)

a.

Remove the old grease from the front drive inboard joint assembly.


b.
C411287C01
2.01,0.51 0.938,0.25 0.938,0.25 1.823,1 true 0.74,0.156 1,0.417 0.26,0.26 10 false *a
*a Matchmark


Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.

NOTICE:

Do not use a punch for the marks.



c.

Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.


d.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.
C411288

Using a snap ring expander, remove the shaft snap ring from the front drive outboard joint shaft assembly.


f.
C141145C17
2.854,1.073 1.844,1.479 1.844,1.479 2.885,1.135 true 1.646,1.427 1.833,1.583 0.188,0.156 10 *a
*a Matchmark


Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.

NOTICE:

Do not use a punch for the marks.



g.

Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Do not drop the tripod joint.




h.
C411289

Remove the front axle inboard joint grommet from the front drive inboard joint assembly.


Hide 7.REMOVE FRONT AXLE INBOARD JOINT BOOT

a.

Remove the front No. 2 axle inboard joint boot clamp, front axle inboard joint boot and front axle inboard joint boot clamp.


Hide 43474F 8.REMOVE FRONT DRIVE SHAFT DAMPER CLAMP (for RH Side with Damper)

a.
C314741C16
0.51,1.844 0.698,1.938 0.698,1.938 1,1.76 false 0.635,1.938 0.948,2.094 0.313,0.156 10 false *a
*a Claw


Using needle-nose pliers, disengage each claw as shown in the illustration and separate the 2 front drive shaft damper clamps.


Hide 43474D 9.REMOVE FRONT DRIVE SHAFT DAMPER (for RH Side with Damper)

a.

Remove the front drive shaft damper and 2 front drive shaft damper clamps from the front drive outboard joint shaft assembly.


Hide 43447F 10.SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

a.
C205159

Using a screwdriver, separate the front No. 2 axle outboard joint boot clamp as shown in the illustration..


Hide 43447E 11.SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP

HINT:

Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.


Hide 12.REMOVE FRONT AXLE OUTBOARD JOINT BOOT

a.

Remove the front axle outboard joint boot clamp, front axle outboard joint boot and front No. 2 axle outboard joint boot clamp from the front drive outboard joint shaft assembly.


b.

Remove the old grease from the front drive outboard joint shaft assembly.