Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for 1KR-FE) › from 2020.07
RM36W0E _52 Drivetrain _087547 DRIVE SHAFT / PROPELLER SHAFT _0430982 FRONT DRIVE SHAFT ASSEMBLY(for 1KR-FE) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 1KR-FE)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43448G 1.SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.
C215097C01
0.375,0.781 0.708,1.323 0.708,1.323 1.292,0.781 false 0.604,1.344 0.792,1.521 0.188,0.177 10 false *a
*a Claw


Using needle-nose pliers, disengage the 2 claws and separate the front No. 2 axle inboard joint boot clamp.


Hide 43448F 2.SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP

a.
C241821

Using pliers, separate the front axle inboard joint boot clamp.


Hide 3.SEPARATE FRONT AXLE INBOARD JOINT BOOT

a.

Separate the front axle inboard joint boot from the front drive inboard joint assembly.


Hide 4.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY

a.

Remove the old grease from the front drive inboard joint assembly.


b.
C411287C01
2.01,0.51 0.938,0.25 0.938,0.25 1.823,1 true 0.74,0.156 1,0.417 0.26,0.26 10 false *a
*a Matchmark


Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.

NOTICE:

Do not use a punch for the marks.



c.

Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.


d.
C411288

Using a snap ring expander, remove the shaft snap ring from the front drive outboard joint shaft assembly.


e.
C141145C17
2.854,1.073 1.844,1.479 1.844,1.479 2.885,1.135 true 1.646,1.427 1.833,1.583 0.188,0.156 10 *a
*a Matchmark


Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.

NOTICE:

Do not use a punch for the marks.



f.

Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Do not drop the tripod joint.




g.
C411289

Remove the front axle inboard joint grommet from the front drive inboard joint assembly.


Hide 5.REMOVE FRONT AXLE INBOARD JOINT BOOT

a.

Remove the front No. 2 axle inboard joint boot clamp, front axle inboard joint boot and front axle inboard joint boot clamp.


Hide 43474F 6.REMOVE FRONT DRIVE SHAFT DAMPER CLAMP (for RH Side)

a.
C411290

Using pliers, separate the 2 front drive shaft damper clamps.


Hide 43474D 7.REMOVE FRONT DRIVE SHAFT DAMPER (for RH Side)

a.

Remove the front drive shaft damper and 2 front drive shaft damper clamps from the front drive outboard joint shaft assembly.


Hide 43447F 8.SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

a.
C160725

Using pliers, separate the front No. 2 axle outboard joint boot clamp.


Hide 43447E 9.SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP

HINT:

Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.


Hide 10.REMOVE FRONT AXLE OUTBOARD JOINT BOOT

a.

Remove the front axle outboard joint boot clamp, front axle outboard joint boot and front No. 2 axle outboard joint boot clamp from the front drive outboard joint shaft assembly.


b.

Remove the old grease from the front drive outboard joint shaft assembly.