Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for 1KR-FE) › from 2020.07
RM36W0E _52 Drivetrain _087547 DRIVE SHAFT / PROPELLER SHAFT _0430982 FRONT DRIVE SHAFT ASSEMBLY(for 1KR-FE) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 1KR-FE)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT AXLE OUTBOARD JOINT BOOT

a.
C166359C04
1.917,0.885 2.427,0.375 2.427,0.375 2.792,0.375 false 2.823,0.281 3.177,0.49 0.354,0.208 10 *a
*a Protective Tape


Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


b.
C274280C01
1.115,1.719 1.115,1.427 false 1.656,1.74 1.656,1.479 false 2.344,1.74 2.344,1.438 false 2.979,1.75 2.979,1.229 false 1.063,1.781 1.375,1.938 0.313,0.156 10 *1 1.604,1.792 1.917,1.948 0.313,0.156 10 *2 2.281,1.781 2.594,1.938 0.313,0.156 10 *3 2.948,1.792 3.26,1.948 0.313,0.156 10 *4
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front No. 2 Axle Outboard Joint Boot Clamp
*3 Front Axle Outboard Joint Boot
*4 Front Axle Outboard Joint Boot Clamp
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts to the front drive outboard joint shaft assembly in the following order:

i.

Front No. 2 axle outboard joint boot clamp


ii.

Front axle outboard joint boot


iii.

Front axle outboard joint boot clamp



c.

Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

Standard Grease Capacity:

91 to 99 g (3.21 to 3.49 oz)



d.

Install the front axle outboard joint boot to the front drive outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the outboard joint boot.

·

Keep the inside of the outboard joint boot free of foreign matter.




Hide 43447F 2.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

a.

Install the front No. 2 axle outboard joint boot clamp to the front axle outboard joint boot.


b.
C112671N02
1.083,0.5 1.302,0.5 1.302,0.5 1.646,0.865 false 0.792,0.427 1.198,0.646 0.406,0.219 10 false SST

Place SST onto the front No. 2 axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


c.

Tighten SST so that the front No. 2 axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



d.

Remove SST.


e.
C112672N06
2.281,1.052 2.771,1.781 true 2.771,1.781 2.99,1.781 false 3.01,1.708 3.385,2.031 0.375,0.323 10 false SST

Using SST, measure the clearance of the front No. 2 axle outboard joint boot clamp.

SST
09240-00021  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0591 in.)


If the clearance is not as specified, retighten SST.


Hide 43447E 3.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

HINT:

Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.


Hide 43474D 4.INSTALL FRONT DRIVE SHAFT DAMPER (for RH Side)

a.
C378898C07
0.708,1.677 0.708,1.365 false 1.406,1.635 1.406,1.323 false 0.208,1.625 0.208,1.313 false 1.552,0.302 1.75,0.531 0.198,0.229 10 false A 1.323,1.677 1.635,1.833 0.313,0.156 10 false *2 0.635,1.708 0.948,1.865 0.313,0.156 10 false *1 0.125,1.656 0.438,1.813 0.313,0.156 10 false *2
*1 Front Drive Shaft Damper
*2 Front Drive Shaft Damper Clamp


Temporarily install the front drive shaft damper and 2 new front drive shaft damper clamps to the front drive outboard joint shaft assembly as shown in the illustration.


b.

Set the dimension (A) as specified below.

Dimension (A):

470.0 to 474.0 mm (1.54 to 1.55 ft.)



Hide 43474F 5.INSTALL FRONT DRIVE SHAFT DAMPER CLAMP (for RH Side)

a.
C411296N01
1.542,1.052 1.094,0.521 1.094,0.521 0.875,0.521 true 0.583,0.438 0.99,0.635 0.406,0.198 10 false SST

Place SST onto the front drive shaft damper clamp, press it against the damper and slightly tighten SST.

SST
09521-24010  


b.

Tighten SST so that the front drive shaft damper clamp is pinched.

NOTICE:

Do not overtighten SST.



c.

Remove SST.


d.
C411297N01
0.635,1.24 1.063,1.24 true 0.333,1.167 0.792,1.365 0.458,0.198 10 false SST

Using SST, measure the clearance of the front drive shaft damper clamp.

SST
09240-00021  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0591 in.)


If the clearance is not as specified, retighten SST.


e.

Perform the same procedure for the other front drive shaft damper clamp.


Hide 6.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

a.
C274277C02
0.688,1.875 0.688,1.333 false 1.698,1.854 1.698,1.615 false 2.49,1.875 2.49,1.667 false 2.927,1.885 2.927,1.25 false 0.625,1.896 0.938,2.052 0.313,0.156 10 *1 1.635,1.896 1.948,2.052 0.313,0.156 10 *2 2.417,1.906 2.729,2.063 0.313,0.156 10 *3 2.875,1.896 3.188,2.052 0.313,0.156 10 *a
*1 Front Axle Inboard Joint Boot Clamp
*2 Front Axle Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp
*a Protective Tape
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts to the front drive outboard joint shaft assembly in the following order:

i.

Front axle inboard joint boot clamp


ii.

Front axle inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Remove the protective tape.


c.
C411292C01
1.438,1.719 2.531,1.958 2.531,1.958 2.021,1.365 true 2.604,1.875 2.927,2.104 0.323,0.229 10 false *a
*a Matchmark


Align the matchmarks and install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the outboard joint end.



d.

Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Keep the tripod joint free of foreign matter.

·

Be sure to install the tripod joint in the correct direction.




e.
C411288

Using a snap ring expander, install a new shaft snap ring to the front drive outboard joint shaft assembly.


f.

Pack the front drive inboard joint assembly and front axle inboard joint boot with grease.

Standard Grease Capacity:

114 to 124 g (4.02 to 4.37 oz)



g.
C411298C01
2.521,1.813 2.354,1.813 2.354,1.813 2.354,1.5 true 2.573,1.719 2.885,1.917 0.313,0.198 10 false *a
*a Groove


Install a new front axle inboard joint grommet to the inboard joint groove.

NOTICE:

Securely fit the protrusion on the front axle inboard joint grommet into the inboard joint groove.



h.
C411287C02
2.031,0.51 0.979,0.396 0.979,0.396 1.833,0.99 true 0.802,0.302 1.094,0.573 0.292,0.271 10 false *a
*a Matchmark


Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.


Hide 7.INSTALL FRONT AXLE INBOARD JOINT BOOT

a.

Install the front axle inboard joint boot to the front drive inboard joint assembly.

NOTICE:
·

Keep the grooves free of grease.

·

Keep the inside of the front axle inboard joint boot free of foreign matter.




b.
C296188N01
1.438,1.656 1.594,1.854 0.156,0.198 10 false A

Check whether the drive shaft dimension (A) is within specification.

Dimension (A):
for LH Side 642.7 mm (2.11 ft.)
for RH Side 817.7 mm (2.68 ft.)



Hide 43448F 8.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

a.

Install the front axle inboard joint boot clamp to the front axle inboard joint boot.


b.
C241890N01
0.698,0.51 0.896,0.51 0.896,0.51 1.552,1.031 true 0.406,0.427 0.76,0.625 0.354,0.198 10 false SST

Place SST onto the front axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


c.

Tighten SST so that the front axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



d.

Remove SST.


e.
C241891N01
1.708,1.25 2.281,1.5 2.281,1.5 2.5,1.5 true 2.552,1.427 2.979,1.635 0.427,0.208 10 false SST

Using SST, measure the clearance of the front axle inboard joint boot clamp.

SST
09240-00021  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0591 in.)


If the clearance is not as specified, retighten SST.


Hide 43448G 9.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.
C215097C01
0.375,0.781 0.708,1.323 0.708,1.323 1.292,0.781 false 0.604,1.344 0.792,1.521 0.188,0.177 10 false *a
*a Claw


Using needle-nose pliers, engage the 2 claws and install the front No. 2 axle inboard joint boot clamp.

NOTICE:

Be careful not to damage the front axle inboard joint boot.