Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2. DISCHARGE FUEL SYSTEM PRESSURE
3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
4.REMOVE REAR SEAT ASSEMBLY
58325E
5.REMOVE REAR FLOOR SERVICE HOLE COVER
Using a clip remover with its tip wrapped with protective tape, remove the rear floor service hole cover and butyl tape.
| *a | Protective Tape | - | - |
Disconnect the 2 fuel suction tube with pump and gauge assembly connectors.
77027B
6.DISCONNECT NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY
Slide the clip and disconnect the No. 1 fuel emission tube sub-assembly from the fuel suction tube with pump and gauge assembly.
77701W
7.DISCONNECT NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY
Slide the clip and disconnect the No. 1 canister outlet hose sub-assembly from the fuel suction tube with pump and gauge assembly.
77209F
8.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.
| *1 | Fuel Suction Plate Sub-assembly | *2 | Tube Joint Clip |
| *3 | Fuel Tank Main Tube Sub-assembly | - | |
| *a | Fuel Tube Joint | *b | O-ring |
| *c | Nylon Tube | - | |
|
Pull off |
|
Pull off |
Remove any foreign matter on the fuel tube joint before performing this work.
Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).
Be sure to disconnect the fuel tube joint by hand.
Do not bend, twist, pinch or kink the nylon tube.
Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.
If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.
77144
9.REMOVE FUEL PUMP GAUGE RETAINER
Remove the fuel pump gauge retainer.
| *a | Insertion Point |
| *b | SST (Plate) |
| *c | SST (Claw) |
| *d | SST (Bolt) |
Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.
Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.
While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).
| *a | SST (Handle) |
| *b | SST (Plate) |
| *c | SST (Claw) |
| *d | SST (Bolt) |
| *e | Extension Bar |
Install SST (handle) and an extension bar to SST (plate).
Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.
Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.
Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.
Do not spin SST too fast or use an impact wrench as this may result in damage to components.
If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.
While pressing down on the fuel suction tube with pump and gauge assembly, remove the fuel pump gauge retainer.
77020A
10.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.
Be careful not to bend the arm of the fuel sender gauge assembly.
Remove the fuel suction tube set gasket from the fuel tank assembly.