Home › Engine / Hybrid System › 1KR-FE (ENGINE MECHANICAL) › CYLINDER HEAD › from 2020.07
RM36W0E _51 Engine / Hybrid System _091035 1KR-FE ENGINE MECHANICAL _0431332 CYLINDER HEAD A

1KR-FE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 and 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.


c.
A322043N02
1.417,1.5 0.604,0.396 0.604,0.396 1.25,1.01 true 0.271,0.333 0.729,0.531 0.458,0.198 10 false SST

Using SST and a hammer, tap out the intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A322060

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Bush Bore Diameter:

9.685 to 9.706 mm (0.3813 to 0.3821 in.)


New Guide Bush Selection Chart (STD or O/S 0.05):
Bush Size Bush Bore Diameter
STD 9.727 to 9.738 mm (0.3830 to 0.3834 in.)
O/S 0.05 9.777 to 9.788 mm (0.3849 to 0.3854 in.)


HINT:

If the bush bore diameter of the cylinder head sub-assembly is greater than 9.706 mm (0.3821 in.), machine the bush bore to a dimension of 9.735 to 9.756 mm (0.3833 to 0.3841 in.) to install an O/S 0.05 valve guide bush.



e.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 and 212°F).


f.

Place the cylinder head sub-assembly on wooden blocks.


g.
A322061C01
1.427,1.51 0.635,0.771 0.635,0.771 1.229,1.01 true 1.031,2.229 1.344,2.385 0.313,0.156 10 false *a 0.333,0.688 0.792,0.885 0.458,0.198 10 false SST
*a Protrusion Height


Using SST and a hammer, tap in a new intake valve guide bush to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

9.8 to 10.4 mm (0.3858 to 0.4094 in.)



h.
A322062

Using a sharp 5.5 mm reamer, ream the intake valve guide bush to obtain the standard clearance between the intake valve guide bush and valve stem.

Standard Oil Clearance:

0.025 to 0.065 mm (0.000984 to 0.002559 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 and 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.


c.
A322044N02
1.688,1.49 1.146,0.438 1.146,0.438 1.844,1.031 true 0.833,0.375 1.292,0.573 0.458,0.198 10 false SST

Using SST and a hammer, tap out the exhaust valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A322063

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Bush Bore Diameter:

9.685 to 9.706 mm (0.3813 to 0.3821 in.)


New Guide Bush Selection Chart (STD or O/S 0.05):
Bush Size Bush Bore Diameter
STD 9.727 to 9.738 mm (0.3830 to 0.3834 in.)
O/S 0.05 9.777 to 9.788 mm (0.3849 to 0.3854 in.)


HINT:

If the bush bore diameter of the cylinder head sub-assembly is greater than 9.706 mm (0.3821 in.), machine the bush bore to a dimension of 9.735 to 9.756 mm (0.3833 to 0.3841 in.) to install an O/S 0.05 valve guide bush.



e.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 and 212°F).


f.

Place the cylinder head sub-assembly on wooden blocks.


g.
A322064C01
1.698,1.458 0.938,0.625 0.938,0.625 1.865,0.99 true 0.188,2.229 0.5,2.385 0.313,0.156 10 false *a 0.625,0.563 1.083,0.76 0.458,0.198 10 false SST
*a Protrusion Height


Using SST and a hammer, tap in a new exhaust valve guide bush to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

9.4 to 10.0 mm (0.3701 to 0.3937 in.)



h.
A322065

Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the standard oil clearance between the exhaust valve guide bush and valve stem.

Standard Oil Clearance:

0.030 to 0.062 mm (0.00118 to 0.00244 in.)



Hide 3.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.
A322066C02
0.115,0.073 0.427,0.229 0.313,0.156 10 false *a 1.542,2.76 2.208,3.104 0.667,0.344 10 false *b 2.604,3.656 3.354,4.177 0.75,0.521 10 false *c
*a Upper Side
*b Width
*c Protrusion Height


Remove the 2 ring pins.


b.

Using a plastic hammer, tap in 2 new ring pins to the specified protrusion height.

Standard Ring Pin:
Item Width Protrusion Height
Ring pin 11.0 mm (0.433 in.) 4.5 to 5.5 mm (0.177 to 0.217 in.)



Hide 4.REPLACE STUD BOLT

NOTICE:

If any of the stud bolts is deformed or the threads are damaged, replace it.


a.

Using an E8 "TORX" socket, install a new stud bolt.

A429308C03
0.104,0.052 0.417,0.25 0.313,0.198 10 false *a 3.604,0.083 3.917,0.281 0.313,0.198 10 false *b 2,2.875 2.313,3.073 0.313,0.198 10 false *c 2,3.375 2.313,3.573 0.313,0.198 10 false *d 5.365,2.865 5.677,3.063 0.313,0.198 10 false *d 5.333,3.406 5.646,3.604 0.313,0.198 10 false *f 2.781,3.125 3.094,3.323 0.313,0.198 10 false *e 6.156,3.052 6.469,3.25 0.313,0.198 10 false *g 1.021,2.302 1.333,2.5 0.313,0.198 10 false A 4.438,2.302 4.75,2.5 0.313,0.198 10 false B 0.563,0.406 0.875,0.604 0.313,0.198 10 false A 0.219,1.052 0.531,1.25 0.313,0.198 10 false A 4.521,1.583 4.833,1.781 0.313,0.198 10 false B 5.854,1.531 6.167,1.729 0.313,0.198 10 false B 6.281,1.698 6.594,1.896 0.313,0.198 10 false B 6.573,1.698 6.885,1.896 0.313,0.198 10 false B 5.75,0.583 5.917,0.75 0.167,0.167 10 true B 4.521,0.552 4.688,0.719 0.167,0.167 10 true B
*a Intake Side *b Exhaust Side
*c 14.0 mm (0.551 in.) *d 13.0 mm (0.512 in.)
*e 29.0 mm (1.14 in.) *f 10.5 mm (0.41 in.)
*g 33.5 mm (1.32 in.) - -


Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)