Home › Engine / Hybrid System › 1KR-FE (ENGINE MECHANICAL) › CYLINDER BLOCK › from 2020.07
RM36W0E _51 Engine / Hybrid System _091035 1KR-FE ENGINE MECHANICAL _0431333 CYLINDER BLOCK A

1KR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 15708 1.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A324437

Using a 5 mm hexagon socket wrench, install the 3 No. 1 oil nozzle sub-assemblies to the cylinderblock sub-assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13101 2.INSTALL PISTON (w/ Pin)

NOTICE:

If the piston pin is removed from the piston, replace the piston, piston pin and connecting rod sub-assembly with new ones.


a.

Gradually heat the piston to between 80 and 90°C (176 and 194°F).


b.

Apply engine oil to the small end of a new connecting rod sub-assembly and a new piston pin.


c.
A421886C01
0.396,1.594 0.542,1.594 0.542,1.594 0.635,1.188 false 2.115,2.115 2.271,2.115 2.271,2.115 2.51,1.271 false 1.146,3.792 1.823,4.438 1.823,4.438 2.563,3.99 false 0.219,1.5 0.531,1.698 0.313,0.198 10 false *a 1.938,2.01 2.25,2.208 0.313,0.198 10 false *a 1.771,4.469 2.083,4.667 0.313,0.198 10 false *a
*a Front Mark


Align the front marks of the piston and connecting rod sub-assembly and insert the connecting rod sub-assembly into the piston.


d.

Using SST and a press, install the piston pin.

A421887C01
0.594,0.833 0.792,0.833 false 0.563,1.281 0.76,1.281 false 0.542,1.75 0.74,1.75 false 2.604,0.604 2.802,0.604 false 2.667,2.021 2.865,2.021 false 2.615,1.49 2.854,1.292 2.854,1.292 2.969,1.292 false 4.115,0.719 4.313,0.719 false 4.417,1.208 4.615,1.208 false 3.563,1.229 3.885,1.229 false 5.781,1.635 5.354,1.021 5.354,1.021 5.771,1.24 false 6.458,1.469 6.656,1.469 false 6.188,1.573 6.375,2.042 6.375,2.042 6.521,2.042 false 6.052,2.156 6.052,1.646 false 0.281,0.76 0.74,0.958 0.458,0.198 10 false SST 0.26,1.188 0.719,1.385 0.458,0.198 10 false SST 0.25,1.688 0.708,1.885 0.458,0.198 10 false SST 2.865,0.521 3.323,0.719 0.458,0.198 10 false SST 2.927,1.948 3.385,2.146 0.458,0.198 10 false SST 3.031,1.208 3.344,1.406 0.313,0.198 10 false *a 4.365,0.625 4.677,0.823 0.313,0.198 10 false *1 3.365,1.135 3.677,1.333 0.313,0.198 10 false *2 4.677,1.146 4.99,1.344 0.313,0.198 10 false *3 5.167,0.865 5.479,1.063 0.313,0.198 10 false *b 6.208,0.635 6.521,0.833 0.313,0.198 10 false *c 6.729,1.375 7.042,1.573 0.313,0.198 10 false *3 6.594,1.948 6.906,2.146 0.313,0.198 10 false *1 5.969,2.188 6.281,2.385 0.313,0.198 10 false *2
*1 Piston Pin *2 Connecting Rod Sub-assembly
*3 Piston - -
*a Front Mark *b Press
*c 1.2 to 2.4 mm (0.0472 to 0.0945 in.) - -
V100135

Rear Side - -


SST
09221-25026  (09221-00021, 09221-00030, 09221-00130, 09221-00141, 09221-00150)

NOTICE:
·

Press in the piston pin from the front mark side of the piston.

·

Do not press in the piston pin at an angle.




e.

Hold the connecting rod sub-assembly and check that the piston moves smoothly.


Hide 13011 3.INSTALL PISTON RING SET

a.
A324460C03
2.813,0.865 2.979,0.865 true 2.667,1.115 3,1.115 true 2.813,1.344 2.979,1.344 true 3.042,0.813 3.354,1.01 0.313,0.198 10 false *1 3.031,1.063 3.344,1.26 0.313,0.198 10 false *2 3.042,1.292 3.354,1.49 0.313,0.198 10 false *3
*1 Upper Side Rail
*2 Expander Spacer
*3 Lower Side Rail


Install the expander spacer and upper side rail and lower side rail by hand.

HINT:

Install the upper side rail and lower side rail with the code mark (T) facing upward.



b.
A324461C03
0.635,3.885 0.948,4.083 0.313,0.198 10 false *2 0.635,2.656 0.948,2.854 0.313,0.198 10 false *1
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
V100135

Upward


Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring as shown in the illustration.

NOTICE:

Install the No. 2 compression ring with the cutout facing downward.



c.
A421888C01
0.917,2.542 1.042,2.542 1.042,2.542 1.333,2.125 false 2.781,2.417 3.094,2.615 0.313,0.198 10 false *1 1.385,2.813 1.698,3.01 0.313,0.198 10 false *3 0.542,1.698 0.854,1.896 0.313,0.198 10 false *4 1.344,0.531 1.656,0.729 0.313,0.198 10 false *2 2.781,0.99 3.094,1.188 0.313,0.198 10 false *5 0.729,2.458 1.042,2.656 0.313,0.198 10 false *a 1.323,1.854 1.781,2.052 0.458,0.198 10 false 72° 1.365,1.49 1.823,1.688 0.458,0.198 10 false 72° 1.917,1.229 2.25,1.438 0.333,0.208 10 true 72° 2.208,1.677 2.667,1.875 0.458,0.198 10 false 72° 1.938,2.083 2.396,2.281 0.458,0.198 10 false 72°
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Upper Side Rail
*4 Expander Spacer
*5 Lower Side Rail
*a Front Mark
V100135

Engine Front


Position the piston ring set so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the ring ends.



Hide 11711 4.INSTALL CRANKSHAFT BEARING

a.

Clean the main journals and both surfaces of the crankshaft bearings.


b.

Install the 4 crankshaft bearings to the cylinder block sub-assembly as shown in the illustration.

A324463C02
5.531,3.104 5.844,3.302 0.313,0.198 10 false *b 4.813,3.104 5.125,3.302 0.313,0.198 10 false *a
*a Correct *b Incorrect
V100135

Engine Front - -


NOTICE:
·

Do not apply engine oil to the crankshaft bearings or the contact surfaces.

·

Both sides of the oil groove in the cylinder block sub-assembly should be visible through the oil feed holes in the crankshaft bearing. The amount visible on each side of the holes should be equal.

·

Do not allow coolant to come into contact with the crankshaft bearing inner surface.

·

If any coolant comes into contact with the crankshaft bearing inner surface, replace the crankshaft bearing with a new one.




c.

Install the 4 crankshaft bearings.

i.
A324464N01
1.385,2.26 1.542,2.458 0.156,0.198 10 false A 1.396,2.74 1.552,2.938 0.156,0.198 10 false B

Install the crankshaft bearings to the crankshaft bearing caps.


ii.

Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and the crankshaft bearing edge.

Difference Between (A) and (B):

0.8 mm (0.0315 in.) or less


NOTICE:

Do not apply engine oil to the crankshaft bearings or the contact surfaces.




Hide 11791 5.INSTALL CRANKSHAFT THRUST WASHER UPPER

a.
A324465C01
1.073,1.219 1.01,0.583 1.01,0.583 0.625,0.948 true 1.052,0.531 1.365,0.729 0.313,0.198 10 false *a
*a Oil Groove


Install the 2 crankshaft thrust washer uppers to the No. 3 journal position of the cylinder block sub-assembly with the oil grooves facing outward.


b.

Apply engine oil to the crankshaft thrust washer uppers.


Hide 13411 6.INSTALL CRANKSHAFT

a.

Apply engine oil to the crankshaft bearings, then place the crankshaft on the cylinder block sub-assembly.


b.

Apply engine oil to the crankshaft bearings.


c.
A324453

Examine the number marks and install the crankshaft bearing caps to the cylinder block sub-assembly.


d.

Apply a light coat of engine oil to the threads and under the heads of the crankshaft bearing cap set bolts.


e.
A324431

Temporarily install the 8 crankshaft bearing cap set bolts.


f.
A324431E01
2.073,0.375 2.229,0.573 0.156,0.198 10 true 1 2.073,1.75 2.229,1.948 0.156,0.198 10 true 2 1.583,0.385 1.74,0.583 0.156,0.198 10 true 3 1.615,1.75 1.771,1.948 0.156,0.198 10 true 4 2.542,0.385 2.698,0.583 0.156,0.198 10 true 5 2.552,1.75 2.708,1.948 0.156,0.198 10 true 6 1.125,0.396 1.281,0.594 0.156,0.198 10 true 7 1.135,1.74 1.292,1.917 0.156,0.177 10 true 8

Uniformly tighten the 8 crankshaft bearing cap set bolts in the order shown in the illustration.

Torque:
59 N*m (602 kgf*cm, 44 ft.*lbf)


g.

Check that the crankshaft turns smoothly.


Hide 13041 7.INSTALL CONNECTING ROD BEARING

a.
A324466C03
1.292,3.01 2.615,3.354 1.323,0.344 10 false *a
*a 2.1 to 2.5 mm


Install the connecting rod bearings to the connecting rod sub-assemblies and connecting rod bearing caps.


b.

Using a vernier caliper, measure the distance between the edges of the connecting rod sub-assemblies and connecting rod bearings, and the connecting rod bearing caps and the connecting rod bearings.

Standard Dimension:

2.1 to 2.5 mm (0.0827 to 0.0984 in.)


NOTICE:

Do not apply engine oil to the connecting rod bearings or the contact surfaces.



Hide 13201 8.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, pistons, and surfaces of the connecting rod bearings.


b.
A421888C01
0.917,2.542 1.042,2.542 1.042,2.542 1.333,2.125 false 2.781,2.417 3.094,2.615 0.313,0.198 10 false *1 1.385,2.813 1.698,3.01 0.313,0.198 10 false *3 0.542,1.698 0.854,1.896 0.313,0.198 10 false *4 1.344,0.531 1.656,0.729 0.313,0.198 10 false *2 2.781,0.99 3.094,1.188 0.313,0.198 10 false *5 0.729,2.458 1.042,2.656 0.313,0.198 10 false *a 1.323,1.854 1.781,2.052 0.458,0.198 10 false 72° 1.365,1.49 1.823,1.688 0.458,0.198 10 false 72° 1.917,1.229 2.25,1.438 0.333,0.208 10 true 72° 2.208,1.677 2.667,1.875 0.458,0.198 10 false 72° 1.938,2.083 2.396,2.281 0.458,0.198 10 false 72°
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Upper Side Rail
*4 Expander Spacer
*5 Lower Side Rail
*a Front Mark
V100135

Engine Front


Position the piston ring set so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the ring ends.



c.
A421889C01
2.729,3.948 1.792,3.542 1.792,3.542 2.698,2.75 false 1.615,3.438 1.927,3.635 0.313,0.198 10 false *a
*a Front Mark


Using a piston ring compressor, push the correctly numbered piston sub-assembly and connecting rod sub-assembly into the cylinder with the front marks of the piston facing forward.

NOTICE:
·

When inserting the piston sub-assembly with connecting rod sub-assembly, do not allow it to make contact with the No. 1 oil nozzle sub-assembly.

·

Match the numbered connecting rod bearing cap with the connecting rod sub-assembly.




d.
A324440C01
0.625,0.552 1.25,0.188 true 1.292,0.115 1.604,0.313 0.313,0.198 10 false *a
*a Front Mark


Check that the front mark of the connecting rod bearing cap is facing in the correct direction and install the connecting rod bearing cap.


e.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.


f.

Install the connecting rod bolts.

NOTICE:

The connecting rod bolts are tightened in 2 progressive steps.



g.

Step 1:

i.
A324441N02
1.656,0.74 2.427,0.25 true 2.479,0.188 2.938,0.385 0.458,0.198 10 false SST

Using SST, alternately tighten the connecting rod bolts of the connecting rod cap in several steps.

SST
09205-16011  

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)



h.

Step 2:

i.
A309020C05
2.094,0.594 2.385,0.344 2.385,0.344 2.583,0.344 false 2.635,0.271 2.948,0.469 0.313,0.198 10 false *a 1.104,0.365 1.417,0.563 0.313,0.198 10 false 90°
*a Paint Mark
V100135

Engine Front


Mark the front of the connecting rod bolts with paint.


ii.

Further tighten the connecting rod bolts 90° as shown in the illustration.



i.

Check that the paint marks are now at a 90° angle to the front.


j.

Check that the crankshaft turns smoothly.


Hide 13516 9.INSTALL OIL JET

a.
A324469C02
1.979,4.333 3.354,4.531 1.375,0.198 10 false *a
*a 23.5 to 33.5°


Install the oil jet to the cylinder block sub-assembly as shown in the illustration.

NOTICE:

Do not tap the tip of the oil jet.