Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.07
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0420309 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B00DF13  Passenger Restraints Disable Switch Circuit Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B00DF13 Passenger Restraints Disable Switch Circuit Open
·

The airbag sensor assembly detects an open in the passenger restraints disable switch circuit for 2 seconds

·

Airbag cut off switch cylinder sub-assembly malfunction

·

Airbag sensor assembly malfunction


·

Harness or connector

·

Airbag cut off switch cylinder sub-assembly

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

WIRING DIAGRAM

B512690E13
4.854,2.979 5.479,3.177 0.625,0.198 10 false H14 4.844,3.146 6.583,3.542 1.74,0.396 10 false Airbag Sensor Assembly 0.542,2.823 1.177,3 0.635,0.177 10 false H15 0.542,2.99 3.552,3.396 3.01,0.406 10 false Airbag Cut Off Switch Cylinder Sub-assembly 2.219,1.115 2.802,1.448 0.583,0.333 10 false 2 1.729,1.115 2.313,1.448 0.583,0.333 10 false PMC+ 1.75,2.302 2.333,2.635 0.583,0.333 10 false PMC- 2.208,2.302 2.792,2.635 0.583,0.333 10 false 1 4.885,1.104 5.469,1.438 0.583,0.333 10 false MSW+ 4.635,1.104 5.219,1.438 0.583,0.333 10 false 22 4.885,2.302 5.469,2.635 0.583,0.333 10 false MSW- 4.635,2.302 5.219,2.635 0.583,0.333 10 false 21

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS

Pre-procedure1

a.
C422859C02
1.521,0.563 1.521,0.99 false 2.625,0.969 2.958,1.313 0.333,0.344 10 false *2 1.448,0.385 1.781,0.542 0.333,0.156 10 false *3 0.406,0.969 0.615,1.208 0.208,0.24 10 false *1
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Wire Harness


Disconnect the connectors from the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.


Procedure1

b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

3.CHECK WIRE HARNESS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WIRE HARNESS
a.
C422877C01
0.781,0.854 1.146,1.073 0.365,0.219 0.76,3.74 1.125,3.958 0.365,0.219 1.833,1.771 1.833,1.688 false 1.25,1.667 1.802,1.094 true 2.417,1.667 1.896,1.094 true 1.281,4.26 1.521,3.927 true 1.948,4.26 1.74,3.927 true 1.625,2.99 1.625,2.74 true 0.375,2.573 0.667,2.917 0.292,0.344 10 false *1 2.75,2.583 3.083,2.917 0.333,0.333 10 false *2 1.563,3.021 1.917,3.25 0.354,0.229 10 false *3 1.771,1.781 2.083,2 0.313,0.219 10 false *4 0.667,0.198 1.073,0.542 0.406,0.344 10 false *b 0.667,3.406 1.083,3.667 0.417,0.26 10 false *a 2.354,2.563 2.583,2.833 0.229,0.271 10 false A 1.979,2.563 2.167,2.833 0.188,0.271 10 false B 1.135,2.573 1.333,2.833 0.198,0.26 10 false C 0.771,2.573 0.917,2.833 0.146,0.26 10 false D 0.844,0.875 1.156,1.052 0.313,0.177 10 false H14 1.083,1.667 1.583,1.917 0.5,0.25 10 false MSW- 2.24,1.667 2.75,1.917 0.51,0.25 10 false MSW+ 1.833,4.271 2.417,4.5 0.583,0.229 10 false PMC+ 1.073,4.271 1.583,4.5 0.51,0.229 10 false PMC- 0.823,3.76 1.167,3.99 0.344,0.229 10 false H15
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Using a service wire, connect terminals 22 (MSW+) and 21 (MSW-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H15-2 (PMC+) - H15-1 (PMC-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

4.INSPECT AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY

OK

5.CLEAR DTC

NG

REPLACE AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY

5.CLEAR DTC
a.
C422833C02
2.094,1 2.219,1.188 0.125,0.188 10 false A 1.938,1 2.083,1.271 0.146,0.271 10 false B 1.083,1.01 1.219,1.198 0.135,0.188 10 false C 0.927,1.01 1.042,1.229 0.115,0.219 10 false D 0.563,1.021 0.833,1.271 0.271,0.25 10 false *1 2.542,1.031 2.906,1.292 0.365,0.26 10 false *2
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC
6.CHECK DTC
a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
B00DF13 is not output A
B00DF13 is output B


HINT:

Codes other than DTC B00DF13 may be output at this time, but they are not related to this check.




A

B