Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM D

1KR-FE ENGINE CONTROL  SFI SYSTEM  INITIALIZATION  


HINT:
·

Perform the idle learning after the ECM has been replaced.

·

Perform the electronic throttle learning and idle learning after the throttle body with motor assembly has been cleaned, installed or replaced.

·

Perform the Clear GPF Deposition Values after the Front exhaust pipe assembly has been replaced. (w/ Gasoline Particulate Filter)



IDLE LEARNING (WHEN THROTTLE BODY WITH MOTOR ASSEMBLY HAS BEEN CLEANED, INSTALLED OR REPLACED)


a.

Perform the electronic throttle learning.*


b.

Start the engine and warm it up until the engine coolant temperature is 80°C (176°F) or higher.


c.

After the engine is warmed up, allow it to idle for 5 minutes with the air conditioning and all accessories off.


d.

Confirm that the idle speed is within the specified range.

Standard:
Engine Idle Speed
790 to 940 rpm


HINT:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in neutral.

·

If a DTC is output again after performing idle learning, perform the electronic throttle learning* again.





IDLE LEARNING (WHEN ECM HAS BEEN REPLACED)


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


A250733E18
0.552,0.771 1.094,1.135 0.542,0.365 10 false 10 km/h 0.719,1.75 1.104,1.948 0.385,0.198 10 false Idling 0.167,2.177 1.083,2.542 0.917,0.365 10 false Ignition Switch ON 2.49,1.646 2.729,1.844 0.24,0.198 10 false [A] 3.198,0.542 3.438,0.74 0.24,0.198 10 false [B] 6.438,3.25 6.677,3.448 0.24,0.198 10 false [E] 4.781,3.26 5.021,3.458 0.24,0.198 10 false [D] 3.208,3 3.948,3.667 0.74,0.667 10 false 20 seconds or more 4.042,3 4.792,3.667 0.75,0.667 10 false 20 seconds or more 5.729,3 6.469,3.667 0.74,0.667 10 false 20 seconds or more 4.115,0.542 4.354,0.74 0.24,0.198 10 false [B] 5.781,0.542 6.021,0.74 0.24,0.198 10 false [B] 3.667,1.646 3.906,1.844 0.24,0.198 10 false [C] 4.583,1.656 4.823,1.854 0.24,0.198 10 false [C] 6.25,1.656 6.49,1.854 0.24,0.198 10 false [C]

a.

Start the engine.


b.

Warm up the engine (engine coolant temperature is 80°C (176°F) or higher, air conditioning and all accessories are off) [A].


c.

Drive the vehicle at 10 km/h (6 mph) or more [B].


d.

Idle the engine for 20 seconds or more [C].


e.

Repeat steps [B] and [C], and check that the idle speed is within the specified range [D].

Standard:
Engine Idle Speed
790 to 940 rpm


HINT:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in neutral.

·

If the idle speed is still out of the specified range, repeat steps [B] and [C] until the idle speed is within the specified range [E].





*: PERFORM ELECTRONIC THROTTLE LEARNING


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

f.

Enter the following menus: Powertrain / Engine / Utility / Electric Throttle Learning.

Powertrain > Engine > Utility
Tester Display
Electric Throttle Learning
50005 372 4708

g.

Confirm the following conditions as instructed on the screen.

·

Ignition switch is ON (Engine stopped)

·

The vehicle is stopped

·

Accelerator pedal is fully released

·

Battery voltage is 10 V or higher

·

Electric Throttle is normal

·

Engine coolant temperature is between 5°C (41°F) and 100°C (212°F)

·

Intake air temperature is 5°C (41°F) or higher



h.

Confirm that the initialization conditions displayed on the GTS screen are satisfied and press ENTER.


i.

Check that "Learning has completed" is displayed on the GTS screen.

HINT:

Electronic throttle learning will not be completed if the battery voltage is low or if the voltage drops momentarily, even though the battery voltage is 10 V or higher with the ignition switch is ON.



j.

Wait 5 seconds or more.


k.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

l.

Check the DTC code, and check that DTCs are not output.

HINT:

If DTCs are output and electric throttle learning failed, turn the ignition switch from off to ON. Relearning will automatically begin. In this case, clear the DTC after turning the ignition switch ON and check that DTCs are not output.




Clear GPF Deposition Values


HINT:

This function initializes the volumes of accumulated ash (metal oxide) and PM (Particulate Matter) recorded by the ECM when replacing the GPF (Gasoline Particulate Filter). (Ash is read only)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / GPF Deposition Values Clear.


e.

According to the display on the GTS, initialize the volumes of accumulated ash and PM.