Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM U

1KR-FE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


A325174E05
2.396,0.448 2.823,0.719 0.427,0.271 5.406,0.469 5.833,0.74 0.427,0.271 5.5,0.521 5.958,0.719 0.458,0.198 10 false A55 2.5,0.5 2.958,0.698 0.458,0.198 10 false D50

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
A55-1 (+B1) - A55-4 (E1) Power source of ECM Ignition switch ON 11 to 14 V
A55-2 (+B) - A55-4 (E1) Power source of ECM Ignition switch ON 11 to 14 V
A55-4 (E1) - Body ground Ground circuit of ECM Always Below 1 Ω
A55-5 (E01) - Body ground Ground circuit of ECM Always Below 1 Ω
A55-9 (MREL) - A55-4 (E1) EFI-MAIN NO. 1 relay operation signal Ignition switch ON 11 to 14 V
A55-15 (BATT) - A55-4 (E1) Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
A55-17 (E02) - Body ground Ground circuit of ECM Always Below 1 Ω
A55-22 (FANL) - A55-4 (E1) FAN NO. 1 relay operation signal Ignition switch ON Cooling fan not operated 11 to 14 V
Idling with A/C on or High engine coolant temperature Cooling fan operated 0 to 1.5 V
A55-23 (FANH) - A55-4 (E1) FAN NO. 2 relay operation signal Idling with high engine coolant temperature Cooling fan operated at high speed 0 to 1.5 V
A55-24 (ST1-) - A55-4 (E1) Stop light switch assembly signal
(opposite of voltage at STP terminal)
Ignition switch ON, brake pedal depressed Below 1.5 V
Ignition switch ON, brake pedal released 11 to 14 V
A55-25 (CANL) - A55-4 (E1) CAN communication line Ignition switch ON Pulse generation
(See waveform 1)
A55-26 (CANH) - A55-4 (E1) CAN communication line Ignition switch ON Pulse generation
(See waveform 2)
A55-59 (FC) - A55-4 (E1) Fuel pump control Ignition switch ON 11 to 14 V
Idling Below 1.5 V
A55-31 (IGR) - A55-4 (E1) Ignition signal Ignition switch ON 11 to 14 V
A55-34 (PEX) - A55-32 (EPEX) Differential pressure sensor signal Ignition switch ON 0.4 to 4.8 V
A55-35 (VCPX) - A55-32 (EPEX) Power source of differential pressure sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
A55-37 (IGSW) - A55-4 (E1) Ignition switch signal Ignition switch ON 11 to 14 V
A55-38 (ELS2) - A55-4 (E1) Current consumer signal Rear defogger ON 11 to 14 V
A55-39 (ELS) - A55-4 (E1) Current consumer signal Tail light ON 11 to 14 V
A55-57 (STP) - A55-4 (E1) Stop light switch assembly signal Brake pedal depressed 11 to 14 V
Brake pedal released Below 1.5 V
A55-41 (SPD) - A55-4 (E1) Vehicle speed signal from combination meter assembly signal Vehicle speed of approximately 20 km/h (12 mph) Pulse generation
(See waveform 3)
A55-44 (NEO) - A55-4 (E1) Crankshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 4)
A55-46 (STA) - A55-4 (E1) Starter signal Ignition switch ON Below 1.5 V
Cranking 5.5 V or higher
A55-47 (VPA) - A55-48 (EPA) Accelerator pedal position sensor (for engine control) Ignition switch ON, accelerator pedal fully released 0.7 to 1.2 V
Ignition switch ON, accelerator pedal fully depressed 2.8 to 4.6 V
A55-49 (VCPA) - A55-48 (EPA) Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
A55-50 (VPA2) - A55-51 (EPA2) Accelerator pedal position sensor Ignition switch ON, accelerator pedal fully released 1.2 to 2.0 V
Ignition switch ON, accelerator pedal fully depressed 3.6 to 4.6 V
A55-52 (VCP2) - A55-51 (EPA2) Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
A55-54 (PB) - A55-55 (BRE2) Vacuum sensor assembly signal Idling with warm engine, brake pedal released 0.5 to 4.5 V
A55-56 (BRVC) - A55-55 (BRE2) Power source of vacuum sensor Ignition switch ON 4.75 to 5.25 V
D50-133 (#2) - A55-5 (E01) No. 2 fuel injector assembly signal Ignition switch ON 11 to 14 V
D50-101 (#3) - A55-5 (E01) No. 3 fuel injector assembly signal Ignition switch ON 11 to 14 V
D50-102 (#1) - A55-5 (E01) No. 1 fuel injector assembly signal Ignition switch ON 11 to 14 V
D50-25 (HT1A) - A55-4 (E1) Heated oxygen sensor (sensor 1) heater operation signal Ignition switch ON 11 to 14 V
D50-24 (HT1B) - A55-4 (E1) Heated oxygen sensor (sensor 2) heater operation signal Ignition switch ON 11 to 14 V
D50-57 (IGT2) - A55-4 (E1) No. 1 ignition coil (No. 2 cylinder) signal Idling Pulse generation
D50-27 (IGT1) - A55-4 (E1) No. 1 ignition coil (No. 1 cylinder) signal Idling Pulse generation
D50-28 (EGR2) - A55-4 (E1) EGR valve assembly operation signal Engine racing Pulse generation
D50-29 (EGR1) - A55-4 (E1) EGR valve assembly operation signal Engine racing Pulse generation
D50-103 (M+) - D50-135 (M-) Throttle actuator operation signal Idling with warm engine Pulse generation
D50-56 (IGT3) - A55-4 (E1) No. 1 ignition coil (No. 3 cylinder) signal Idling Pulse generation
D50-58 (EGR4) - A55-4 (E1) EGR valve assembly operation signal Engine racing Pulse generation
D50-59 (EGR3) - A55-4 (E1) EGR valve assembly operation signal Engine racing Pulse generation
D50-73 (OE1+) - D50-72 (OE1-) Camshaft timing oil control valve assembly (for exhaust camshaft) signal Engine speed maintained at 2500 rpm after warming up engine Pulse generation
(See waveform 5)
D50-75 (OCV+) - D50-74 (OCV-) Camshaft timing oil control valve assembly (for intake camshaft) signal Engine speed maintained at 2500 rpm after warming up engine Pulse generation
(See waveform 6)
D50-55 (EVP1) - A55-4 (E1) Purge VSV operation signal Ignition switch ON 11 to 14 V
Idling, under purge control Pulse generation
(See waveform 7)
D50-77 (VCNE)* - A55-4 (E1) Power source of crankshaft position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D50-78 (NE+) - D50-79 (NE-) Crankshaft position sensor signal Idling with warm engine Pulse generation
D50-20 (R) - A55-4 (E1) Back-up light switch assembly signal Back-up light switch on 11 to 14 V
A55-28 (D) - A55-4 (E1) Clutch switch assembly signal Ignition switch ON, clutch pedal released Below 1.5 V
Ignition switch ON, clutch pedal depressed 11 to 14 V
D50-80 (EV1+) - D50-81 (EV1-) Camshaft position sensor (for exhaust camshaft) signal Idling with warm engine Pulse generation
D50-82 (G2+) - D50-114 (G2-) Camshaft position sensor (for intake camshaft) signal Idling with warm engine Pulse generation
D50-117 (VTA1) - D50-115 (ETA) Throttle position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.2 to 1.0 V
Ignition switch ON, accelerator pedal fully depressed 4.0 to 4.8 V
D50-83 (VTA2) - D50-115 (ETA) Throttle position sensor signal (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 4.0 to 4.8 V
Ignition switch ON, accelerator pedal fully depressed 0.2 to 1.0 V
D50-128 (THA) - D50-127 (E21) Intake air temperature sensor signal (built into manifold absolute pressure sensor) Idling, intake air temperature 20°C (68°F) 1.5 to 3.0 V
D50-129 (PIM) - D50-127 (E21) Manifold absolute pressure sensor signal Idling 1.2 to 2.0 V
D50-120 (THW) - D50-121 (ETHW) Engine coolant temperature sensor signal Idling with warm engine, engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
D50-100 (#5) - A55-5 (E01) No. 2 fuel injector assembly signal Ignition switch ON 11 to 14 V
D50-126 (OX1A) - D50-125 (E11) Heated oxygen sensor (sensor 1) signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
D50-124 (OX1B) - D50-123 (E12) Heated oxygen sensor (sensor 2) signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
D50-111 (NSW) - A55-4 (E1) Clutch start switch signal Ignition switch ON (Clutch pedal fully depressed) Below 1.5 V
Ignition switch ON (Clutch pedal released) 11 to 14 V
D50-112 (VCE1) - A55-4 (E1) Power source of camshaft position sensor (for exhaust camshaft) (specific voltage) Ignition switch ON 4.5 to 5.5 V
D50-113 (VCG2) - A55-4 (E1) Power source of camshaft position sensor (for intake camshaft) (specific voltage) Ignition switch ON 4.5 to 5.5 V
D50-116 (VC) - D50-115 (ETA) Power source of throttle position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D50-95 (VC2) - D50-127 (E21) Power source of manifold absolute pressure sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D50-97 (KNK1) - D50-96 (EKNK) Knock control sensor signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 8)
D50-131 (#4) - A55-5 (E01) No. 1 fuel injector assembly signal Ignition switch ON 11 to 14 V
D50-132 (#6) - A55-5 (E01) No. 3 fuel injector assembly signal Ignition switch ON 11 to 14 V

*: w/ Stop and Start System

WAVEFORM 1


A283577E16
3.01,1.365 3.375,1.604 0.365,0.24 10 false GND

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 2


A283576E18
3.01,1.396 3.344,1.708 0.333,0.313 10 false GND

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 3


A207838E06
2.875,1.198 3.24,1.354 0.365,0.156 10 false GND

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Vehicle speed of approximately 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 4


A301717E06
3.104,1.677 3.427,1.875 0.323,0.198 10 false GND

Engine Speed Signal
ECM Terminal Name Between NEO and E1
Tester Range 5 V/DIV., 2 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 5


A283575E22
0.51,1.125 1.021,1.385 0.51,0.26 10 false GND

Camshaft Timing Oil Control Valve Assembly (for Exhaust Camshaft) Signal
ECM Terminal Name Between OE1+ and OE1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 2500 rpm after warming up engine


WAVEFORM 6


A283575E23
0.51,1.125 1.021,1.385 0.51,0.26 10 false GND

Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft) Signal
ECM Terminal Name Between OCV+ and OCV-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 2500 rpm after warming up engine


WAVEFORM 7


A170545E06
2.948,1.063 3.427,1.385 0.479,0.323 10 false GND

Purge VSV Signal
ECM Terminal Name Between EVP1 and E1
Tester Range 10 V/DIV., 20 ms/DIV
Condition Idling, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 8


A283572E40
2.615,1 3.115,1.292 0.5,0.292 10 false GND

Knock Control Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle condition.