Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.07
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0420309 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located in the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then turns off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

If a malfunction occurs in the airbag sensor assembly, combination meter assembly or wire harness connected to the airbag sensor assembly or combination meter assembly, the SRS warning light comes on.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in case the power source voltage drops.

When the auxiliary battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage. In addition, when the voltage drops, the SRS warning light will illuminate.

The SRS warning light automatically turns off when the power source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag sensor assembly to the combination meter assembly via CAN communication.

WIRING DIAGRAM

C422876E01
4.906,0.615 5.75,0.948 0.844,0.333 10 false A/BAG-IGR 2.135,2.188 3,2.583 0.865,0.396 10 false METER-IGR 3.448,2.875 3.833,3.167 0.385,0.292 10 false ES 3.188,1.917 3.417,2.167 0.229,0.25 10 false 38 3.188,2.76 3.365,3.073 0.177,0.313 10 false 23 6.083,0.469 6.5,0.792 0.417,0.323 10 false IGR 6.083,2.365 6.5,2.667 0.417,0.302 10 false E1 6.083,2.875 6.5,3.167 0.417,0.292 10 false E2 5.917,3.667 6.583,3.865 0.667,0.198 10 false H14 3.333,3.656 3.917,3.865 0.583,0.208 10 false H6 5.917,3.865 6.854,4.667 0.938,0.802 10 false Airbag Sensor Assembly 3.333,3.865 4.552,4.615 1.219,0.75 10 false Combination Meter Assembly 5.802,0.344 6.083,0.688 0.281,0.344 10 false 36 5.802,2.26 6.083,2.583 0.281,0.323 10 false 33 5.802,2.76 6.083,3.083 0.281,0.323 10 false 32 3.458,2 3.833,2.25 0.375,0.25 10 false IG+ 0.75,4.313 2.75,4.688 2,0.375 10 false : CAN Communication Line 3.25,0.438 4.25,1.094 1,0.656 10 false from IGR-NO. 1 Relay 0.458,2 1.5,2.917 1.042,0.917 10 false from IGR-NO. 1 Relay*2 0.469,1.188 2.156,1.656 1.688,0.469 10 false from Engine Stop and Start ECU*1 2.688,1.073 2.938,1.281 0.25,0.208 10 false *1 2.021,1.906 2.271,2.115 0.25,0.208 10 false *2 2.729,1.906 2.979,2.115 0.25,0.208 10 false *2 0.167,3.5 4.448,3.698 4.281,0.198 10 false *1: w/ Stop and Start System 0.167,3.917 4.448,4.115 4.281,0.198 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK VEHICLE CONTROL HISTORY (RoB)
a.

Check for Vehicle Control History (RoB) codes.

Body Electrical > SRS Airbag > Utility
Tester Display
Vehicle Control History (RoB)
50005 444 55

Result:
Result Proceed to
Code X210B is output A
Code X210B is not output B



A

2.CHECK AUXILIARY BATTERY VOLTAGE

B

4.CHECK SRS WARNING LIGHT OPERATION
2.CHECK AUXILIARY BATTERY VOLTAGE
a.

Measure the voltage of the auxiliary battery with the ignition switch off.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

NG

REPLACE OR RECHARGE AUXILIARY BATTERY

3.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.
B475057C39
0.552,0.552 0.927,0.781 0.375,0.229 2.49,1.875 2.125,1.458 true 1.969,1.865 1.844,1.448 true 1.396,1.865 1.74,1.448 true 0.083,0.063 0.521,0.469 0.438,0.406 10 false *a 2.406,1.885 2.833,2.104 0.427,0.219 10 false IGR 1.313,1.885 1.74,2.104 0.427,0.219 10 false E2 1.906,1.885 2.333,2.104 0.427,0.219 10 false E1 0.615,0.583 0.917,0.792 0.302,0.208 10 false H14
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


c.

Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H14-36 (IGR) - Body ground Ignition switch ON 8 to 16 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H14-33 (E1) - Body ground Always Below 1 Ω
H14-32 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

END (POWER SOURCE VOLTAGE DROPPED TEMPORARILY, BUT HAS RETURNED TO NORMAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SRS WARNING LIGHT OPERATION
a.

Turn the ignition switch to ON and check the SRS warning light condition.

HINT:

The primary check is performed for approximately 6 seconds after the ignition switch is turned to ON.



Result:
Result Proceed to
After the primary check period, the SRS warning light remains on. A
After the primary check period, the SRS warning light turns off and comes on again. B



A

5.CHECK AUXILIARY BATTERY VOLTAGE

B

9.CHECK CAN COMMUNICATION SYSTEM
5.CHECK AUXILIARY BATTERY VOLTAGE
a.

Measure the voltage of the auxiliary battery with the ignition switch off.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK CONNECTOR (AIRBAG SENSOR ASSEMBLY SIDE)

NG

REPLACE OR RECHARGE AUXILIARY BATTERY

6.CHECK CONNECTOR (AIRBAG SENSOR ASSEMBLY SIDE)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connector is properly connected to the airbag sensor assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not properly connected, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the airbag sensor assembly.


e.

Check that the terminals of the connector are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

7.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.
B475057C39
0.552,0.552 0.927,0.781 0.375,0.229 2.49,1.875 2.125,1.458 true 1.969,1.865 1.844,1.448 true 1.396,1.865 1.74,1.448 true 0.083,0.063 0.521,0.469 0.438,0.406 10 false *a 2.406,1.885 2.833,2.104 0.427,0.219 10 false IGR 1.313,1.885 1.74,2.104 0.427,0.219 10 false E2 1.906,1.885 2.333,2.104 0.427,0.219 10 false E1 0.615,0.583 0.917,0.792 0.302,0.208 10 false H14
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


c.

Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H14-36 (IGR) - Body ground Ignition switch ON 8 to 16 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H14-33 (E1) - Body ground Always Below 1 Ω
H14-32 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK SRS WARNING LIGHT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK SRS WARNING LIGHT
a.
C431635C02
1.479,1.604 1.479,1.156 false 0.563,1.021 0.833,1.271 0.271,0.25 10 false *1 2.542,1.031 2.906,1.292 0.365,0.26 10 false *2 1.417,1.625 1.781,1.885 0.365,0.26 10 false *3
*1 Combination Meter Assembly
*2 Airbag Sensor Assembly
*3 Wire Harness


Turn the ignition switch to ON and check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light turns off for approximately 10 seconds and then turns back on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY

9.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

OK:

CAN communication system is functioning normally.


HINT:

Refer to Communication Bus Check in CAN Communication System.




Result:
Result Proceed to
OK A
NG (for HV Model) B
NG (for Gasoline Model) C



A

10.CHECK AUXILIARY BATTERY VOLTAGE

B

C

10.CHECK AUXILIARY BATTERY VOLTAGE
a.

Measure the voltage of the auxiliary battery with the ignition switch off.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK CONNECTOR (AIRBAG SENSOR ASSEMBLY SIDE)

NG

REPLACE OR RECHARGE AUXILIARY BATTERY

11.CHECK CONNECTOR (AIRBAG SENSOR ASSEMBLY SIDE)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connector is properly connected to the airbag sensor assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not properly connected, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the airbag sensor assembly.


e.

Check that the terminals of the connector are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

12.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.
B475057C39
0.552,0.552 0.927,0.781 0.375,0.229 2.49,1.875 2.125,1.458 true 1.969,1.865 1.844,1.448 true 1.396,1.865 1.74,1.448 true 0.083,0.063 0.521,0.469 0.438,0.406 10 false *a 2.406,1.885 2.833,2.104 0.427,0.219 10 false IGR 1.313,1.885 1.74,2.104 0.427,0.219 10 false E2 1.906,1.885 2.333,2.104 0.427,0.219 10 false E1 0.615,0.583 0.917,0.792 0.302,0.208 10 false H14
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


c.

Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H14-36 (IGR) - Body ground Ignition switch ON 8 to 16 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H14-33 (E1) - Body ground Always Below 1 Ω
H14-32 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK CONNECTOR (COMBINATION METER ASSEMBLY SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK CONNECTOR (COMBINATION METER ASSEMBLY SIDE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



b.

Check that the connector is properly connected to the combination meter assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not properly connected, reconnect the connector and proceed to the next inspection.



c.

Disconnect the connector from the combination meter assembly.


d.

Check that the terminals of the connector are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

14.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.
B515929C06
1.531,0.167 1.865,0.385 0.333,0.219 0.333,1.813 0.688,1.354 true 2.708,1.344 3.052,1.802 true 0.083,0.052 0.406,0.271 0.323,0.219 10 false *a 3,1.813 3.333,2.052 0.333,0.24 10 false IG+ 1.615,0.188 1.865,0.385 0.25,0.198 10 false H6 0.24,1.823 0.573,2.063 0.333,0.24 10 false ES
*a Front view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H6-38 (IG+) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-23 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK SRS WARNING LIGHT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK SRS WARNING LIGHT
a.
C431635C02
1.479,1.604 1.479,1.156 false 0.563,1.021 0.833,1.271 0.271,0.25 10 false *1 2.542,1.031 2.906,1.292 0.365,0.26 10 false *2 1.417,1.625 1.781,1.885 0.365,0.26 10 false *3
*1 Combination Meter Assembly
*2 Airbag Sensor Assembly
*3 Wire Harness


Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



b.

Connect the connector to the combination meter assembly.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON and check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light turns off for approximately 10 seconds and then turns back on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY