Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR (for TMMF Made) › 2020.07–2021.11
RM36W0E _59 Vehicle Exterior _088061 MIRROR (EXT) _0431796 OUTER REAR VIEW MIRROR(for TMMF Made) G

MIRROR (EXT)  OUTER REAR VIEW MIRROR(for TMMF Made)  INSPECTION  


PROCEDURE

Hide 87940 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Power Retract Mirror)

a.

Check the operation of the mirror surface.

i.
B563076C03
1.583,1.729 2.01,1.958 0.427,0.229 2.125,2.854 2.313,3.177 true 2.323,2.802 2.646,2.917 true 1.604,3.208 1.875,2.844 true 0.906,1.875 1.104,2.031 0.198,0.156 10 false *a 2.333,3.188 2.635,3.354 0.302,0.167 10 false M+ 1.406,3.219 1.667,3.385 0.26,0.167 10 false MH 2.688,2.906 2.927,3.073 0.24,0.167 10 false MV 1.688,1.771 2.146,1.969 0.458,0.198 10 false L10
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Apply voltage and check the operation of the outer rear view mirror assembly LH.

OK:
Tester Connection Specified Condition
L10-3 (MV) - Auxiliary battery positive (+)
L10-7 (M+) - Auxiliary battery negative (-)
Turns upward
L10-7 (M+) - Auxiliary battery positive (+)
L10-3 (MV) - Auxiliary battery negative (-)
Turns downward
L10-6 (MH) - Auxiliary battery positive (+)
L10-7 (M+) - Auxiliary battery negative (-)
Turns left
L10-7 (M+) - Auxiliary battery positive (+)
L10-6 (MH) - Auxiliary battery negative (-)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.

Check the operation of the mirror heater. (w/ Mirror Heater)

i.
B582201C01
1.563,1.667 1.969,1.885 0.406,0.219 0.979,3.219 1.271,2.844 true 2.24,2.417 2.677,2.354 true 0.885,1.875 1.198,2.031 0.313,0.156 10 false *a 0.875,3.167 1.188,3.323 0.313,0.156 10 false - 2.729,2.292 3.042,2.448 0.313,0.156 10 false + 1.646,1.698 1.958,1.854 0.313,0.156 10 false L10
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L10-2 (+) - L10-4 (-) 25°C 10.5 to 12.8 Ω


If the result is not as specified, check the outer mirror LH.


ii.

Connect a cable from the positive (+) auxiliary battery terminal to terminal 2 and negative (-) auxiliary battery terminal to terminal 4, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, check the outer mirror LH.



c.

Check the side turn signal light assembly LH.

i.
B585922C03
1.51,0.323 1.927,0.573 0.417,0.25 1.74,1.854 1.479,1.469 true 0.875,1.875 1.177,1.469 true 0.563,0.677 0.875,0.833 0.313,0.156 10 false *a 1.771,1.906 2.083,2.063 0.313,0.156 10 false B 0.792,1.854 1.104,2.01 0.313,0.156 10 false - 1.594,0.375 1.917,0.625 0.323,0.25 10 false L10
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition
L10-5 (B) - Auxiliary battery positive (+)
L10-4 (-) - Auxiliary battery negative (-)
Side turn light illuminates


If the result is not as specified, inspect the side turn signal light assembly LH or replace the outer rear view mirror assembly LH.



Hide 87910 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Power Retract Mirror)

a.

Check the operation of the mirror surface.

i.
B563074C02
1.563,1.667 1.969,1.885 0.406,0.219 1.604,3.198 1.875,2.833 true 2.146,2.844 2.302,3.167 true 2.344,2.792 2.563,2.927 true 0.885,1.875 1.198,2.031 0.313,0.156 10 false *a 2.573,2.938 2.885,3.094 0.313,0.156 10 false MV 2.344,3.177 2.656,3.333 0.313,0.156 10 false M+ 1.375,3.198 1.688,3.354 0.313,0.156 10 false MH 1.646,1.698 1.958,1.854 0.313,0.156 10 false K10
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Apply voltage and check the operation of the outer rear view mirror assembly RH.

OK:
Tester Connection Specified Condition
K10-3 (MV) - Auxiliary battery positive (+)
K10-7 (M+) - Auxiliary battery negative (-)
Turns upward
K10-7 (M+) - Auxiliary battery positive (+)
K10-3 (MV) - Auxiliary battery negative (-)
Turns downward
K10-6 (MH) - Auxiliary battery positive (+)
K10-7 (M+) - Auxiliary battery negative (-)
Turns left
K10-7 (M+) - Auxiliary battery positive (+)
K10-6 (MH) - Auxiliary battery negative (-)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.

Check the operation of the mirror heater. (w/ Mirror Heater)

i.
B582202C01
1.563,1.667 1.969,1.885 0.406,0.219 0.979,3.219 1.271,2.844 true 2.26,2.438 2.635,2.292 true 0.885,1.875 1.198,2.031 0.313,0.156 10 false *a 0.875,3.177 1.188,3.333 0.313,0.156 10 false - 2.688,2.219 3,2.375 0.313,0.156 10 false + 1.646,1.698 1.958,1.854 0.313,0.156 10 false K10
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K10-2 (+) - K10-4 (-) 25°C 10.5 to 12.8 Ω


If the result is not as specified, check the outer mirror RH.


ii.

Connect a cable from the positive (+) auxiliary battery terminal to terminal 2 and negative (-) auxiliary battery terminal to terminal 4, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, check the outer mirror RH.



c.

Check the side turn signal light assembly RH.

i.
B585922C04
1.51,0.323 1.927,0.573 0.417,0.25 1.708,1.875 1.458,1.5 true 0.885,1.865 1.188,1.458 true 0.604,0.677 0.917,0.833 0.313,0.156 10 false *a 1.729,1.885 2.042,2.042 0.313,0.156 10 false B 0.76,1.844 1.073,2 0.313,0.156 10 false - 1.594,0.375 1.917,0.625 0.323,0.25 10 false K10
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition
K10-5 (B) - Auxiliary battery positive (+)
K10-4 (-) - Auxiliary battery negative (-)
Side turn light illuminates


If the result is not as specified, inspect the side turn signal light assembly RH or replace the outer rear view mirror assembly RH.



Hide 87940 3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Power Retract Mirror)

a.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.

Disconnect the outer rear view mirror assembly LH connector.


ii.
B582195C01
1.521,1.771 1.906,2.01 0.385,0.24 1.104,3.271 1.479,3.021 true 0.688,2.313 1.438,2.646 true 1.208,0.01 1.521,0.208 0.313,0.198 10 false (A) 0.99,0.49 1.302,0.688 0.313,0.198 10 false (B) 0.969,1.125 1.281,1.323 0.313,0.198 10 false (C) 1.313,1.438 1.625,1.635 0.313,0.198 10 false (D) 1.948,1.531 2.26,1.729 0.313,0.198 10 false (E) 1.604,1.813 1.917,2.01 0.313,0.198 10 false L14 0.552,1.844 0.865,2.042 0.313,0.198 10 false *a 0.427,2.198 0.74,2.396 0.313,0.198 10 false MR 0.896,3.229 1.208,3.406 0.313,0.177 10 false MF
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Tester Connection Condition Specified Condition
L14-3 (MR) - Auxiliary battery positive (+)
L14-9 (MF) - Auxiliary battery negative (-)
Forward position (A) Moves from (A) to (E)
L14-9 (MF) - Auxiliary battery positive (+)
L14-3 (MR) - Auxiliary battery negative (-)
Forward position (A) Does not move
L14-3 (MR) - Auxiliary battery positive (+)
L14-9 (MF) - Auxiliary battery negative (-)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
L14-9 (MF) - Auxiliary battery positive (+)
L14-3 (MR) - Auxiliary battery negative (-)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
L14-3 (MR) - Auxiliary battery positive (+)
L14-9 (MF) - Auxiliary battery negative (-)
Driving position (C) Moves from (C) to (E)
L14-9 (MF) - Auxiliary battery positive (+)
L14-3 (MR) - Auxiliary battery negative (-)
Driving position (C) Does not move
L14-3 (MR) - Auxiliary battery positive (+)
L14-9 (MF) - Auxiliary battery negative (-)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
L14-9 (MF) - Auxiliary battery positive (+)
L14-3 (MR) - Auxiliary battery negative (-)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
L14-3 (MR) - Auxiliary battery positive (+)
L14-9 (MF) - Auxiliary battery negative (-)
Retracted position (E) Does not move
L14-9 (MF) - Auxiliary battery positive (+)
L14-3 (MR) - Auxiliary battery negative (-)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.

Check the operation of the mirror surface.

i.
B582197C01
1.552,1.771 1.885,1.99 0.333,0.219 2.281,1.792 1.917,2.667 true 2.167,2.635 2.698,2 true 2.427,2.708 2.802,2.708 true 1.604,1.802 1.917,2 0.313,0.198 10 false L14 0.521,1.917 0.833,2.115 0.313,0.198 10 false *a 2.844,2.625 3.156,2.823 0.313,0.198 10 false MV 2.323,1.698 2.635,1.896 0.313,0.198 10 false MH 2.75,1.906 3.063,2.104 0.313,0.198 10 false M+
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Apply voltage and check the operation of the outer rear view mirror assembly LH.

OK:
Tester Connection Specified Condition
L14-6 (MV) - Auxiliary battery positive (+)
L14-5 (M+) - Auxiliary battery negative (-)
Turns upward
L14-5 (M+) - Auxiliary battery positive (+)
L14-6 (MV) - Auxiliary battery negative (-)
Turns downward
L14-4 (MH) - Auxiliary battery positive (+)
L14-5 (M+) - Auxiliary battery negative (-)
Turns right
L14-5 (M+) - Auxiliary battery positive (+)
L14-4 (MH) - Auxiliary battery negative (-)
Turns left


If the result is not as specified, replace the outer rear view mirror assembly LH.



c.

Check the operation of the mirror heater.

i.
B582199C01
1.521,1.771 1.917,1.99 0.396,0.219 0.625,2.323 1.24,2.646 true 2.198,2.969 2.844,2.969 true 0.5,1.781 0.813,1.979 0.313,0.198 10 false *a 1.615,1.802 1.927,2 0.313,0.198 10 false L14 0.49,2.229 0.802,2.427 0.313,0.198 10 false + 2.927,2.865 3.24,3.063 0.313,0.198 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L14-2 (M+) - L14-11 (-) 25°C 10.5 to 12.8 Ω


If the result is not as specified, check the outer mirror LH.


ii.

Connect a cable from the positive (+) auxiliary battery terminal to terminal 2 and the negative (-) auxiliary battery terminal to terminal 11, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, check the outer mirror LH.



d.

Check the side turn signal light assembly LH.

i.
B585923C01
1.5,0.24 1.917,0.49 0.417,0.25 2.427,1.948 2.25,1.594 true 1.708,1.917 1.854,1.604 true 0.385,0.438 0.698,0.594 0.313,0.156 10 false *a 2.51,1.885 2.917,2.135 0.406,0.25 10 false - 1.542,1.906 1.927,2.104 0.385,0.198 10 false B 1.604,0.281 2.01,0.531 0.406,0.25 10 false L14
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition
L14-10 (B) - Auxiliary battery positive (+)
L14-11 (-) - Auxiliary battery negative (-)
Side turn light illuminates


If the result is not as specified, inspect the side turn signal light assembly LH or replace the outer rear view mirror assembly LH.



e.

Check the operation of the blind spot monitor indicator. (w/ Blind Spot Monitor System)

i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.
B585923C02
1.5,0.208 1.917,0.458 0.417,0.25 0.698,1.146 1.063,1.271 true 2.229,1.604 2.542,1.938 true 0.167,0.146 0.479,0.302 0.313,0.156 10 false *a 0.302,1.052 0.74,1.25 0.438,0.198 10 false BSL+ 2.604,1.917 3.042,2.115 0.438,0.198 10 false - 1.594,0.25 1.938,0.479 0.344,0.229 10 false L14
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Apply 6 V dry-cell battery voltage to the terminals of the connector, and check the blind spot monitor indicator condition.

OK:
Tester Connection Specified Condition
L14-1 (BSL+) - Positive (+) end of the 6 V dry-cell battery
L14-11 (-) - Negative (-) end of the 6 V dry-cell battery
Blind spot monitor indicator comes on


NOTICE:

Do not apply a voltage of 6 V or higher.


If the result is not as specified, inspect the outer mirror LH or replace the outer rear view mirror assembly LH.



Hide 87910 4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Power Retract Mirror)

a.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.

Disconnect the outer rear view mirror assembly RH connector.


ii.
B582196C01
1.5,1.781 1.906,2.01 0.406,0.229 1.438,2.656 0.625,2.271 true 1.479,3.021 1.229,3.281 true 2.01,0.01 2.323,0.208 0.313,0.198 10 false (A) 2.229,0.49 2.542,0.688 0.313,0.198 10 false (B) 2.281,1.125 2.594,1.323 0.313,0.198 10 false (C) 1.958,1.417 2.271,1.615 0.313,0.198 10 false (D) 1.344,1.542 1.656,1.74 0.313,0.198 10 false (E) 0.583,1.958 0.896,2.156 0.313,0.198 10 false *a 0.979,3.219 1.292,3.417 0.313,0.198 10 false MF 0.375,2.177 0.688,2.375 0.313,0.198 10 false MR 1.583,1.823 1.896,2.021 0.313,0.198 10 false K14
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Tester Connection Condition Specified Condition
K14-3 (MR) - Auxiliary battery positive (+)
K14-9 (MF) - Auxiliary battery negative (-)
Forward position (A) Moves from (A) to (E)
K14-9 (MF) - Auxiliary battery positive (+)
K14-3 (MR) - Auxiliary battery negative (-)
Forward position (A) Does not move
K14-3 (MR) - Auxiliary battery positive (+)
K14-9 (MF) - Auxiliary battery negative (-)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
K14-9 (MF) - Auxiliary battery positive (+)
K14-3 (MR) - Auxiliary battery negative (-)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
K14-3 (MR) - Auxiliary battery positive (+)
K14-9 (MF) - Auxiliary battery negative (-)
Driving position (C) Moves from (C) to (E)
K14-9 (MF) - Auxiliary battery positive (+)
K14-3 (MR) - Auxiliary battery negative (-)
Driving position (C) Does not move
K14-3 (MR) - Auxiliary battery positive (+)
K14-9 (MF) - Auxiliary battery negative (-)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
K14-9 (MF) - Auxiliary battery positive (+)
K14-3 (MR) - Auxiliary battery negative (-)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
K14-3 (MR) - Auxiliary battery positive (+)
K14-9 (MF) - Auxiliary battery negative (-)
Retracted position (E) Does not move
K14-9 (MF) - Auxiliary battery positive (+)
K14-3 (MR) - Auxiliary battery negative (-)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.

Check the operation of the mirror surface.

i.
B582198C01
1.49,1.604 1.875,1.823 0.385,0.219 1.094,1.833 1.854,2.656 true 2.156,2.635 2.729,1.979 true 2.427,2.719 2.781,2.719 true 0.542,1.917 0.854,2.115 0.313,0.198 10 false *a 1.563,1.646 1.875,1.844 0.313,0.198 10 false K14 2.823,2.635 3.177,2.865 0.354,0.229 10 false MV 0.833,1.75 1.188,1.979 0.354,0.229 10 false MH 2.771,1.896 3.125,2.125 0.354,0.229 10 false M+
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Apply voltage and check the operation of the outer rear view mirror assembly RH.

OK:
Tester Connection Specified Condition
K14-6 (MV) - Auxiliary battery positive (+)
K14-5 (M+) - Auxiliary battery negative (-)
Turns upward
K14-5 (M+) - Auxiliary battery positive (+)
K14-6 (MV) - Auxiliary battery negative (-)
Turns downward
K14-4 (MH) - Auxiliary battery positive (+)
K14-5 (M+) - Auxiliary battery negative (-)
Turns left
K14-5 (M+) - Auxiliary battery positive (+)
K14-4 (MH) - Auxiliary battery negative (-)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



c.

Check the operation of the mirror heater.

i.
B582200C01
1.531,1.74 1.917,1.99 0.385,0.25 1.25,2.656 0.604,2.417 true 2.219,3 2.75,3 true 0.531,1.948 0.844,2.146 0.313,0.198 10 false *a 1.615,1.771 1.927,1.969 0.313,0.198 10 false K14 0.427,2.313 0.74,2.51 0.313,0.198 10 false + 2.823,2.906 3.135,3.104 0.313,0.198 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K14-2 (+) - K14-11 (-) 25°C 10.5 to 12.8 Ω


If the result is not as specified, check the outer mirror RH.


ii.

Connect a cable from the positive (+) auxiliary battery terminal to terminal 2 and negative (-) auxiliary battery terminal to terminal 11, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, check the outer mirror RH.



d.

Check the side turn signal light assembly RH.

i.
B585923C03
1.5,0.24 1.917,0.49 0.417,0.25 2.396,1.927 2.219,1.573 true 1.667,1.927 1.854,1.604 true 0.385,0.438 0.698,0.594 0.313,0.156 10 false *a 2.448,1.896 2.854,2.146 0.406,0.25 10 false - 1.5,1.927 1.885,2.125 0.385,0.198 10 false B 1.604,0.281 2.01,0.531 0.406,0.25 10 false K14
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition
K14-10 (B) - Auxiliary battery positive (+)
K14-11 (-) - Auxiliary battery negative (-)
Side turn light illuminates


If the result is not as specified, inspect the side turn signal light assembly RH or replace the outer rear view mirror assembly RH.



e.

Check the operation of the blind spot monitor indicator. (w/ Blind Spot Monitor System)

i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.
B585923C04
1.5,0.208 1.917,0.458 0.417,0.25 0.698,1.146 1.063,1.271 true 2.198,1.615 2.552,1.969 true 0.167,0.146 0.479,0.302 0.313,0.156 10 false *a 0.302,1.052 0.74,1.25 0.438,0.198 10 false BSR+ 2.615,1.927 3.052,2.125 0.438,0.198 10 false - 1.594,0.25 1.938,0.479 0.344,0.229 10 false K14
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Apply 6 V dry-cell battery voltage to the terminals of the connector, and check the blind spot monitor indicator condition.

OK:
Tester Connection Specified Condition
K14-1 (BSR+) - Positive (+) end of the 6 V dry-cell battery
K14-11 (-) - Negative (-) end of the 6 V dry-cell battery
Blind spot monitor indicator comes on


NOTICE:

Do not apply a voltage of 6 V or higher.


If the result is not as specified, inspect the outer mirror RH or replace the outer rear view mirror assembly RH.