Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH › from 2020.07
RM36W0E _59 Vehicle Exterior _088061 MIRROR (EXT) _0421714 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSTALL OUTER MIRROR SWITCH ASSEMBLY (w/o Power Retract Mirror)

a.

Check the mirror select and surface adjust switch. (for LHD)

i.
B581959C01
1.479,2.198 1.833,2.479 0.354,0.281 2.094,1 2.354,0.385 true 1.229,3.552 0.771,2.927 true 1.438,3.552 1.125,2.667 true 1.583,3.542 1.479,2.563 true 1.771,3.552 1.854,2.573 true 1.917,3.552 2.323,2.719 true 2.438,4.271 2.167,3.833 true 1.104,4.292 1.438,3.854 true 2.344,0.281 2.677,0.531 0.333,0.25 10 false *a 0.177,2.302 0.531,2.51 0.354,0.208 10 false *b 0.604,2.865 0.854,3.115 0.25,0.25 10 false B 0.896,2.604 1.229,2.854 0.333,0.25 10 false VR 1.281,2.49 1.615,2.74 0.333,0.25 10 false HL 1.917,2.49 2.25,2.74 0.333,0.25 10 false HR 2.375,2.625 2.708,2.875 0.333,0.25 10 false VL 0.958,4.333 1.292,4.583 0.333,0.25 10 false M+ 2.417,4.333 2.667,4.583 0.25,0.25 10 false E 1.542,2.26 2,2.458 0.458,0.198 10 false L12
*a Mirror Select and Surface Adjust Switch
*b Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select and surface adjust switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
L12-6 (B) - L12-2 (VL) Up Below 1 Ω
L12-7 (E) - L12-11 (M+) Up Below 1 Ω
L12-6 (B) - L12-2 (VL) Off 10 kΩ or higher
L12-7 (E) - L12-11 (M+) Off 10 kΩ or higher
L12-6 (B) - L12-11 (M+) Down Below 1 Ω
L12-7 (E) - L12-2 (VL) Down Below 1 Ω
L12-6 (B) - L12-11 (M+) Off 10 kΩ or higher
L12-7 (E) - L12-2 (VL) Off 10 kΩ or higher
L12-6 (B) - L12-4 (HL) Left Below 1 Ω
L12-7 (E) - L12-11 (M+) Left Below 1 Ω
L12-6 (B) - L12-4 (HL) Off 10 kΩ or higher
L12-7 (E) - L12-11 (M+) Off 10 kΩ or higher
L12-6 (B) - L12-11 (M+) Right Below 1 Ω
L12-7 (E) - L12-4 (HL) Right Below 1 Ω
L12-6 (B) - L12-11 (M+) Off 10 kΩ or higher
L12-7 (E) - L12-4 (HL) Off 10 kΩ or higher



iii.

Turn the mirror select and surface adjust switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
L12-6 (B) - L12-5 (VR) Up Below 1 Ω
L12-7 (E) - L12-11 (M+) Up Below 1 Ω
L12-6 (B) - L12-5 (VR) Off 10 kΩ or higher
L12-7 (E) - L12-11 (M+) Off 10 kΩ or higher
L12-6 (B) - L12-11 (M+) Down Below 1 Ω
L12-7 (E) - L12-5 (VR) Down Below 1 Ω
L12-6 (B) - L12-11 (M+) Off 10 kΩ or higher
L12-7 (E) - L12-5 (VR) Off 10 kΩ or higher
L12-6 (B) - L12-3 (HR) Left Below 1 Ω
L12-7 (E) - L12-11 (M+) Left Below 1 Ω
L12-6 (B) - L12-3 (HR) Off 10 kΩ or higher
L12-7 (E) - L12-11 (M+) Off 10 kΩ or higher
L12-6 (B) - L12-11 (M+) Right Below 1 Ω
L12-7 (E) - L12-3 (HR) Right Below 1 Ω
L12-6 (B) - L12-11 (M+) Off 10 kΩ or higher
L12-7 (E) - L12-3 (HR) Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check that the LED illuminates. (for LHD)

i.
B581959C02
1.458,2.531 1.875,2.781 0.417,0.25 2.135,3.521 2.5,2.917 true 0.917,4.333 1.25,3.844 true 0.813,4.333 1.302,4.552 0.49,0.219 10 false ILL+ 2.552,2.823 3.042,3.042 0.49,0.219 10 false ILL- 0.292,2.823 0.75,3.135 0.458,0.313 10 false *a 1.552,2.573 2.01,2.771 0.458,0.198 10 false L12
*a Component without harness connected
(Outer Mirror Switch Assembly)


Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.

OK:
Tester Connection Specified Condition
L12-12 (ILL+) - Auxiliary battery positive (+)
L12-1 (ILL-) - Auxiliary battery negative (-)
LED illuminates


If the result is not as specified, replace the outer mirror switch assembly.



c.

Check the mirror select and surface adjust switch. (for RHD)

i.
B581957C01
1.479,2.198 1.833,2.479 0.354,0.281 1.375,1 1.635,0.385 true 1.229,3.552 0.771,2.927 true 1.438,3.552 1.125,2.667 true 1.583,3.542 1.479,2.563 true 1.771,3.552 1.854,2.573 true 1.917,3.552 2.323,2.719 true 2.438,4.271 2.167,3.833 true 1.104,4.292 1.438,3.854 true 1.677,0.281 2.01,0.531 0.333,0.25 10 false *a 0.177,2.302 0.531,2.51 0.354,0.208 10 false *b 0.604,2.865 0.854,3.115 0.25,0.25 10 false B 0.896,2.604 1.229,2.854 0.333,0.25 10 false VR 1.281,2.49 1.615,2.74 0.333,0.25 10 false HL 1.917,2.49 2.25,2.74 0.333,0.25 10 false HR 2.375,2.625 2.708,2.875 0.333,0.25 10 false VL 0.958,4.333 1.292,4.583 0.333,0.25 10 false M+ 2.417,4.333 2.667,4.583 0.25,0.25 10 false E 1.542,2.26 2,2.458 0.458,0.198 10 false K12
*a Mirror Select and Surface Adjust Switch
*b Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select and surface adjust switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
K12-6 (B) - K12-2 (VL) Up Below 1 Ω
K12-7 (E) - K12-11 (M+) Up Below 1 Ω
K12-6 (B) - K12-2 (VL) Off 10 kΩ or higher
K12-7 (E) - K12-11 (M+) Off 10 kΩ or higher
K12-6 (B) - K12-11 (M+) Down Below 1 Ω
K12-7 (E) - K12-2 (VL) Down Below 1 Ω
K12-6 (B) - K12-11 (M+) Off 10 kΩ or higher
K12-7 (E) - K12-2 (VL) Off 10 kΩ or higher
K12-6 (B) - K12-4 (HL) Left Below 1 Ω
K12-7 (E) - K12-11 (M+) Left Below 1 Ω
K12-6 (B) - K12-4 (HL) Off 10 kΩ or higher
K12-7 (E) - K12-11 (M+) Off 10 kΩ or higher
K12-6 (B) - K12-11 (M+) Right Below 1 Ω
K12-7 (E) - K12-4 (HL) Right Below 1 Ω
K12-6 (B) - K12-11 (M+) Off 10 kΩ or higher
K12-7 (E) - K12-4 (HL) Off 10 kΩ or higher



iii.

Turn the mirror select and surface adjust switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
K12-6 (B) - K12-5 (VR) Up Below 1 Ω
K12-7 (E) - K12-11 (M+) Up Below 1 Ω
K12-6 (B) - K12-5 (VR) Off 10 kΩ or higher
K12-7 (E) - K12-11 (M+) Off 10 kΩ or higher
K12-6 (B) - K12-11 (M+) Down Below 1 Ω
K12-7 (E) - K12-5 (VR) Down Below 1 Ω
K12-6 (B) - K12-11 (M+) Off 10 kΩ or higher
K12-7 (E) - K12-5 (VR) Off 10 kΩ or higher
K12-6 (B) - K12-3 (HR) Left Below 1 Ω
K12-7 (E) - K12-11 (M+) Left Below 1 Ω
K12-6 (B) - K12-3 (HR) Off 10 kΩ or higher
K12-7 (E) - K12-11 (M+) Off 10 kΩ or higher
K12-6 (B) - K12-11 (M+) Right Below 1 Ω
K12-7 (E) - K12-3 (HR) Right Below 1 Ω
K12-6 (B) - K12-11 (M+) Off 10 kΩ or higher
K12-7 (E) - K12-3 (HR) Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



d.

Check that the LED illuminates. (for RHD)

i.
B581957C02
1.458,2.531 1.875,2.781 0.417,0.25 2.135,3.521 2.5,2.917 true 0.917,4.333 1.25,3.844 true 0.813,4.333 1.302,4.552 0.49,0.219 10 false ILL+ 2.552,2.823 3.042,3.042 0.49,0.219 10 false ILL- 0.292,2.823 0.75,3.135 0.458,0.313 10 false *a 1.552,2.573 2.01,2.771 0.458,0.198 10 false K12
*a Component without harness connected
(Outer Mirror Switch Assembly)


Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.

OK:
Tester Connection Specified Condition
K12-12 (ILL+) - Auxiliary battery positive (+)
K12-1 (ILL-) - Auxiliary battery negative (-)
LED illuminates


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSTALL OUTER MIRROR SWITCH ASSEMBLY (w/ Power Retract Mirror)

a.

Check the mirror select and surface adjust switch. (for LHD)

i.
B581958C04
1.479,2.198 1.833,2.479 0.354,0.281 2.083,1 2.344,0.385 true 1.229,3.552 0.771,2.927 true 1.438,3.552 1.125,2.667 true 1.583,3.542 1.479,2.563 true 1.771,3.552 1.854,2.573 true 1.917,3.552 2.323,2.719 true 2.438,4.271 2.167,3.833 true 1.104,4.292 1.438,3.854 true 2.333,0.281 2.667,0.531 0.333,0.25 10 false *a 0.177,2.302 0.531,2.51 0.354,0.208 10 false *b 0.604,2.865 0.854,3.115 0.25,0.25 10 false B 0.896,2.604 1.229,2.854 0.333,0.25 10 false VR 1.281,2.49 1.615,2.74 0.333,0.25 10 false HL 1.917,2.49 2.25,2.74 0.333,0.25 10 false HR 2.375,2.625 2.708,2.875 0.333,0.25 10 false VL 0.958,4.333 1.292,4.583 0.333,0.25 10 false M+ 2.417,4.333 2.667,4.583 0.25,0.25 10 false E 1.542,2.26 2,2.458 0.458,0.198 10 false L12
*a Mirror Select and Surface Adjust Switch
*b Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select and surface adjust switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
L12-6 (B) - L12-2 (VL) Up Below 1 Ω
L12-7 (E) - L12-11 (M+) Up Below 1 Ω
L12-6 (B) - L12-2 (VL) Off 10 kΩ or higher
L12-7 (E) - L12-11 (M+) Off 10 kΩ or higher
L12-6 (B) - L12-11 (M+) Down Below 1 Ω
L12-7 (E) - L12-2 (VL) Down Below 1 Ω
L12-6 (B) - L12-11 (M+) Off 10 kΩ or higher
L12-7 (E) - L12-2 (VL) Off 10 kΩ or higher
L12-6 (B) - L12-4 (HL) Left Below 1 Ω
L12-7 (E) - L12-11 (M+) Left Below 1 Ω
L12-6 (B) - L12-4 (HL) Off 10 kΩ or higher
L12-7 (E) - L12-11 (M+) Off 10 kΩ or higher
L12-6 (B) - L12-11 (M+) Right Below 1 Ω
L12-7 (E) - L12-4 (HL) Right Below 1 Ω
L12-6 (B) - L12-11 (M+) Off 10 kΩ or higher
L12-7 (E) - L12-4 (HL) Off 10 kΩ or higher



iii.

Turn the mirror select and surface adjust switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
L12-6 (B) - L12-5 (VR) Up Below 1 Ω
L12-7 (E) - L12-11 (M+) Up Below 1 Ω
L12-6 (B) - L12-5 (VR) Off 10 kΩ or higher
L12-7 (E) - L12-11 (M+) Off 10 kΩ or higher
L12-6 (B) - L12-11 (M+) Down Below 1 Ω
L12-7 (E) - L12-5 (VR) Down Below 1 Ω
L12-6 (B) - L12-11 (M+) Off 10 kΩ or higher
L12-7 (E) - L12-5 (VR) Off 10 kΩ or higher
L12-6 (B) - L12-3 (HR) Left Below 1 Ω
L12-7 (E) - L12-11 (M+) Left Below 1 Ω
L12-6 (B) - L12-3 (HR) Off 10 kΩ or higher
L12-7 (E) - L12-11 (M+) Off 10 kΩ or higher
L12-6 (B) - L12-11 (M+) Right Below 1 Ω
L12-7 (E) - L12-3 (HR) Right Below 1 Ω
L12-6 (B) - L12-11 (M+) Off 10 kΩ or higher
L12-7 (E) - L12-3 (HR) Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror retract switch. (for LHD)

i.
B581958C05
1.479,2.198 1.833,2.479 0.354,0.281 1.042,1.208 0.552,0.469 true 2.188,4.292 1.979,3.854 true 1.885,4.292 1.771,3.865 true 1.448,4.302 1.583,3.865 true 0.396,0.333 0.729,0.583 0.333,0.25 10 false *a 0.177,2.302 0.531,2.51 0.354,0.208 10 false *b 1.333,4.333 1.667,4.583 0.333,0.25 10 false MR 1.75,4.333 2.167,4.583 0.417,0.25 10 false MAT 2.167,4.333 2.417,4.583 0.25,0.25 10 false E 1.542,2.26 2,2.458 0.458,0.198 10 false L12
*a Retractable Outer Mirror Switch
*b Component without harness connected
(Outer Mirror Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L12-9 (MAT) - L12-8 (E) AUTO position Below 1 Ω
L12-9 (MAT) - L12-8 (E) Except AUTO position 10 kΩ or higher
L12-10 (MR) - L12-8 (E) Retract position Below 1 Ω
L12-10 (MR) - L12-8 (E) Except retract position 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



c.

Check that the LED illuminates. (for LHD)

i.
B581958C03
1.458,2.531 1.875,2.781 0.417,0.25 2.135,3.521 2.5,2.917 true 0.917,4.333 1.25,3.844 true 0.813,4.333 1.302,4.552 0.49,0.219 10 false ILL+ 2.552,2.823 3.042,3.042 0.49,0.219 10 false ILL- 0.292,2.823 0.75,3.135 0.458,0.313 10 false *a 1.552,2.573 2.01,2.771 0.458,0.198 10 false L12
*a Component without harness connected
(Outer Mirror Switch Assembly)


Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.

OK:
Tester Connection Specified Condition
L12-12 (ILL+) - Auxiliary battery positive (+)
L12-1 (ILL-) - Auxiliary battery negative (-)
LED illuminates


If the result is not as specified, replace the outer mirror switch assembly.



d.

Check the mirror select and surface adjust switch. (for RHD)

i.
B533656C17
1.479,2.198 1.833,2.479 0.354,0.281 1.375,1 1.635,0.385 true 1.229,3.552 0.771,2.927 true 1.438,3.552 1.125,2.667 true 1.583,3.542 1.479,2.563 true 1.771,3.552 1.854,2.573 true 1.917,3.552 2.323,2.719 true 2.438,4.271 2.167,3.833 true 1.104,4.292 1.438,3.854 true 1.677,0.281 2.01,0.531 0.333,0.25 10 false *a 0.229,2.635 0.646,2.885 0.417,0.25 10 false *b 0.604,2.865 0.854,3.115 0.25,0.25 10 false B 0.896,2.604 1.229,2.854 0.333,0.25 10 false VR 1.281,2.49 1.615,2.74 0.333,0.25 10 false HL 1.917,2.49 2.25,2.74 0.333,0.25 10 false HR 2.375,2.625 2.708,2.875 0.333,0.25 10 false VL 0.958,4.333 1.292,4.583 0.333,0.25 10 false M+ 2.417,4.333 2.667,4.583 0.25,0.25 10 false E 1.542,2.26 2,2.458 0.458,0.198 10 false K12
*a Mirror Select and Surface Adjust Switch
*b Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select and surface adjust switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
K12-6 (B) - K12-2 (VL) Up Below 1 Ω
K12-7 (E) - K12-11 (M+) Up Below 1 Ω
K12-6 (B) - K12-2 (VL) Off 10 kΩ or higher
K12-7 (E) - K12-11 (M+) Off 10 kΩ or higher
K12-6 (B) - K12-11 (M+) Down Below 1 Ω
K12-7 (E) - K12-2 (VL) Down Below 1 Ω
K12-6 (B) - K12-11 (M+) Off 10 kΩ or higher
K12-7 (E) - K12-2 (VL) Off 10 kΩ or higher
K12-6 (B) - K12-4 (HL) Left Below 1 Ω
K12-7 (E) - K12-11 (M+) Left Below 1 Ω
K12-6 (B) - K12-4 (HL) Off 10 kΩ or higher
K12-7 (E) - K12-11 (M+) Off 10 kΩ or higher
K12-6 (B) - K12-11 (M+) Right Below 1 Ω
K12-7 (E) - K12-4 (HL) Right Below 1 Ω
K12-6 (B) - K12-11 (M+) Off 10 kΩ or higher
K12-7 (E) - K12-4 (HL) Off 10 kΩ or higher



iii.

Turn the mirror select and surface adjust switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
K12-6 (B) - K12-5 (VR) Up Below 1 Ω
K12-7 (E) - K12-11 (M+) Up Below 1 Ω
K12-6 (B) - K12-5 (VR) Off 10 kΩ or higher
K12-7 (E) - K12-11 (M+) Off 10 kΩ or higher
K12-6 (B) - K12-11 (M+) Down Below 1 Ω
K12-7 (E) - K12-5 (VR) Down Below 1 Ω
K12-6 (B) - K12-11 (M+) Off 10 kΩ or higher
K12-7 (E) - K12-5 (VR) Off 10 kΩ or higher
K12-6 (B) - K12-3 (HR) Left Below 1 Ω
K12-7 (E) - K12-11 (M+) Left Below 1 Ω
K12-6 (B) - K12-3 (HR) Off 10 kΩ or higher
K12-7 (E) - K12-11 (M+) Off 10 kΩ or higher
K12-6 (B) - K12-11 (M+) Right Below 1 Ω
K12-7 (E) - K12-3 (HR) Right Below 1 Ω
K12-6 (B) - K12-11 (M+) Off 10 kΩ or higher
K12-7 (E) - K12-3 (HR) Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



e.

Check the mirror retract switch. (for RHD)

i.
B533656C18
1.479,2.198 1.833,2.479 0.354,0.281 2.469,1.208 2.896,0.521 true 2.188,4.292 1.979,3.854 true 1.885,4.292 1.771,3.865 true 1.448,4.302 1.583,3.865 true 2.865,0.344 3.198,0.594 0.333,0.25 10 false *a 0.198,2.583 0.615,2.833 0.417,0.25 10 false *b 1.333,4.333 1.667,4.583 0.333,0.25 10 false MR 1.75,4.333 2.167,4.583 0.417,0.25 10 false MAT 2.167,4.333 2.417,4.583 0.25,0.25 10 false E 1.542,2.26 2,2.458 0.458,0.198 10 false K12
*a Retractable Outer Mirror Switch
*b Component without harness connected
(Outer Mirror Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K12-9 (MAT) - K12-8 (E) AUTO position Below 1 Ω
K12-9 (MAT) - K12-8 (E) Except AUTO position 10 kΩ or higher
K12-10 (MR) - K12-8 (E) Retract position Below 1 Ω
K12-10 (MR) - K12-8 (E) Except retract position 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



f.

Check that the LED illuminates. (for RHD)

i.
B533656C16
1.458,2.531 1.875,2.781 0.417,0.25 2.135,3.521 2.5,2.917 true 0.917,4.333 1.25,3.844 true 0.813,4.333 1.302,4.552 0.49,0.219 10 false ILL+ 2.552,2.823 3.042,3.042 0.49,0.219 10 false ILL- 0.292,2.823 0.75,3.135 0.458,0.313 10 false *a 1.552,2.573 2.01,2.771 0.458,0.198 10 false K12
*a Component without harness connected
(Outer Mirror Switch Assembly)


Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.

OK:
Tester Connection Specified Condition
K12-12 (ILL+) - Auxiliary battery positive (+)
K12-1 (ILL-) - Auxiliary battery negative (-)
LED illuminates


If the result is not as specified, replace the outer mirror switch assembly.