Home › Brake › BRAKE (REAR) › REAR BRAKE (w/ Electric Parking Brake System) › from 2020.07
RM36W0E _54 Brake _089429 BRAKE (REAR) _0432126 REAR BRAKE(w/ Electric Parking Brake System) A

BRAKE (REAR)  REAR BRAKE(w/ Electric Parking Brake System)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 2.PERFORM REAR BRAKE PAD REPLACEMENT MODE

Hide 3.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 47319F 4.DISCONNECT REAR FLEXIBLE HOSE

a.
C437963

Remove the union bolt and gasket, and disconnect the rear flexible hose from the rear disc brake cylinder assembly.


Hide 890C0A 5.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Hide 46310B 6.REMOVE PARKING BRAKE ACTUATOR ASSEMBLY

Hide 47850 7.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C437964C01
0.771,2.521 1.083,2.677 0.313,0.156 10 false *a 1.49,2.688 1.802,2.844 0.313,0.156 10 false *b
*a Turn
*b Hold


Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and rear disc brake cylinder assembly.


Hide 04466 8.REMOVE REAR DISC BRAKE PAD

a.
C437965

Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.


Hide 04946 9.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM

Hide 10.REMOVE REAR DISC BRAKE PAD SUPPORT PLATE

a.
C437966

Remove the 4 rear disc brake pad support plates from the rear disc brake cylinder mounting.

NOTICE:

Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.



Hide 11.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C437967C01
0.635,0.271 0.833,0.271 true 0.917,1.854 1.167,1.854 true 0.688,1.76 0.917,1.938 0.229,0.177 10 true *1 0.406,0.177 0.635,0.365 0.229,0.188 10 true *2
*1 Rear No. 1 Disc Brake Cylinder Slide Pin
*2 Rear No. 2 Disc Brake Cylinder Slide Pin


Remove the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin from the rear disc brake cylinder mounting.


b.
C437968C01
2.094,1.25 2.51,0.833 true 2.552,0.729 2.865,0.927 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from the rear No. 1 disc brake cylinder slide pin.

NOTICE:

Do not damage the rear No. 1 disc brake cylinder slide pin.



Hide 12.REMOVE REAR DISC BRAKE BUSHING DUST BOOT

a.
C437969

Remove the 2 rear disc brake bushing dust boots from the rear disc brake cylinder mounting.


Hide 47822 13.REMOVE REAR DISC BRAKE CYLINDER MOUNTING

a.
C437970

Remove the 2 bolts and rear disc brake cylinder mounting.


Hide 42431 14.REMOVE REAR DISC

a.
C437971C01
1.885,1.479 2.583,1.677 2.583,1.677 1.917,1.417 true 2.625,1.583 2.938,1.74 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the rear disc and rear axle hub and bearing assembly.


b.

Remove the rear disc.