Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2020.07–2020.09
RM36W0E _51 Engine / Hybrid System _090986 STOP AND START _0432127 STOP AND START SYSTEM U

STOP AND START  STOP AND START SYSTEM  FAIL-SAFE CHART  


If any of the following DTCs are stored, the engine stop and start ECU enters fail-safe mode to preserve vehicle operability.

DTC Component Fail-safe Operation Fail-safe Deactivation Condition
P033562 Open in engine speed signal circuit
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


All of the following conditions are met for 10 seconds:
·

Normal communication with ECM

·

Engine speed 500 rpm or higher

·

Engine speed (communication signal) 500 rpm or higher

·

Difference between engine speed from pulse signal and engine speed from communication signal is less than 100 rpm


P055500
P05552A
·

Vacuum sensor assembly

·

Brake booster assembly

·

Vacuum hose (brake booster hose)


·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


One of the following conditions is met:
·

Vacuum changes while the brake pedal is depressed

·

Vacuum changes a specified number of times while the vehicle is being driven faster than a certain vehicle speed


P055511
P055515
Vacuum sensor assembly circuit
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Sensor output is within standard range
P060629 Engine stop and start ECU
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Pass condition detected and ignition switch turned to ON
P060B1C
P060B49
P060B71
Analog to digital converter (Engine stop and start ECU)
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Pass condition detected and ignition switch turned to ON
P061519 ST NO. 1 relay circuit Stop and start control is prohibited Pass condition detected and DTCs are cleared
P061562 Starter circuit
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Communication with ECM returns to normal and one of the following conditions is met:
·

The STA signal detected by the ECM and STA signals detected by the engine stop and start ECU are on for 0.3 seconds and "Tandem Starter" displayed for "Starter Type" in the Data List

·

The STA signal detected by the ECM and STA signals detected by the engine stop and start ECU are off for 5 seconds and "Tandem Starter" displayed for "Starter Type" in the Data List.


P085011*1
P085015*1
Neutral position switch Stop and start control is prohibited Pass condition detected and ignition switch turned to ON
P085012*2
P085014*2
Park/Neutral position switch assembly circuit
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Pass condition detected and ignition switch turned to ON
P094296*2 Oil pump with motor assembly circuit
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Pass condition detected and DTCs are cleared
P0C2B11*2
P0C2B15*2
P279796*2
Oil pump with motor assembly circuit
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Pass condition detected and ignition switch turned to ON
P154563 Starter assembly
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


DTCs and number of starter operations stored in the ECU (after replacing the starter) are cleared
P160F00 Charging control system
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Pass condition detected and ignition switch turned to ON
P164400
·

Starter drive circuit

·

ST NO. 1 relay

·

Engine stop and start ECU


·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Voltage of engine stop and start ECU internal drive circuit for starter is correct when engine is idling and restarted
P16449E Engine stop and start ECU
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Pass condition detected and ignition switch turned to ON
P186262*1
·

Clutch start switch assembly (for lower)

·

Clutch switch assembly (for upper)


·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Clutch start switch assembly (for lower) and clutch switch assembly (for upper) remain off for 0.5 seconds or more.
P253014 IG signal circuit
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


All of the following conditions are met for 10 seconds or more:
·

Ignition switch ON

·

Normal communication with ECM

·

Ignition switch (communication) ON.


P30DF62
P30EF4B
P323A00
P323A16
P323AA2
P323B29
P323B38
Backup boost converter circuit
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Pass condition detected and DTCs are cleared
P323A19 Backup boost converter circuit
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


·

Pass condition detected and ignition switch turned to ON

·

DTCs (for overcurrent caused by audio volume setting) are cleared


P33B300 External backup boost converter (eco run vehicle converter assembly) circuit
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


1 second after external backup boost converter (eco run vehicle converter assembly) circuit becomes idle
U010087 CAN communication (ECM)
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Communication with engine stop and start ECU continues for 2 seconds
U010187 CAN communication (TCM)
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Communication with engine stop and start ECU continues for 21.6 seconds
U012687 CAN communication (steering sensor)
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Communication with engine stop and start ECU continues for 2 seconds
U012987 CAN communication (skid control ECU (brake actuator assembly))
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Communication with engine stop and start ECU continues for 4.4 seconds
U013187 CAN communication (power steering ECU)
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Communication with engine stop and start ECU continues for 2 seconds
U014087 CAN communication (main body ECU (multiplex network body ECU))
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Communication with engine stop and start ECU continues for 7.2 seconds
U015187 CAN communication (airbag sensor assembly)
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Communication with engine stop and start ECU continues for 21.2 seconds
U015587 CAN communication (combination meter assembly)
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Communication with engine stop and start ECU continues for 21.2 seconds
U016487 CAN communication (air conditioning amplifier assembly)
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Communication with engine stop and start ECU continues for 21.2 seconds
U111087 CAN communication (clearance warning ECU assembly)
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Communication with engine stop and start ECU continues for 2 seconds
U117087 Local CAN communication (skid control ECU (brake actuator assembly))
·

Stop and start control is prohibited

·

Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control


Communication with engine stop and start ECU continues for 21.2 seconds

*1: for Manual Transaxle

*2: for CVT