Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2020.07–2020.09
RM36W0E _51 Engine / Hybrid System _090986 STOP AND START _0432127 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P323A19  Backup Boost Converter "A" Circuit Current Above Threshold  


DESCRIPTION

A backup boost converter is built into the engine stop and start ECU.

The backup boost converter helps maintain auxiliary battery voltage to prevent various functions from failing if power source voltage supplied from the backup boost converter drops due to the high electrical load when the engine is restarted by stop and start control.

The backup boost converter helps maintain the power source voltage if the auxiliary battery voltage drops due to the high electrical load when the engine is restarted by stop and start control.

HINT:

A relay function and fuse function are provided in the backup boost converter.

If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse and relay functions shut off the malfunctioning circuit to protect other circuits (remains shut off until next trip).

When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.

The fuse function is reset* when the ignition switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the ignition switch is turned to ON.

*: A semiconductor fuse self resets according to electric signal.

The backup boost converter supplies power to:
·

Meter / gauge system

·

Power steering system

·

Audio and visual system

·

Navigation system

·

Headup display system

·

Tire pressure warning system

·

Toyota Safety Sense

·

Air conditioning system (for Automatic Air Conditioning System)

·

Parking support brake system



DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P323A19 Backup Boost Converter "A" Circuit Current Above Threshold The following condition continues for 1 second or more (1 trip detection logic):
·

Overcurrent is detected at the B41, B42, B43 and IG41 terminals in the engine stop and start ECU


·

Wire harness or connector

·

Engine stop and start ECU

·

Door control and tire pressure monitoring system receiver assembly

·

Radio and display receiver assembly*1

·

Navigation ECU*2

·

Meter mirror subassembly*3

·

Combination meter assembly

·

Power steering ECU with motor assembly

·

Air conditioning control assembly*4

·

Millimeter wave radar sensor assembly*5

·

Clearance warning ECU assembly*6


Blinks DTC stored SAE Code: P323A

*1: w/ Radio receiver

*2: w/ Navigation System

*3: w/ Headup Display

*4: for Automatic Air conditioning System

*5: w/ Toyota Safety Sense

*6: w/ Parking Support Brake System


CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the auxiliary battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the auxiliary battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the auxiliary battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

for CVT

i.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

ii.

Start the engine and warm it up.


iii.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



iv.

Depress the brake pedal and stop the vehicle.


v.

Keep the engine stopped by stop and start control for 1 second or more. (Keep the shift lever in D.)


vi.

Release the brake pedal with the shift lever in D to start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the auxiliary battery voltage is low.



vii.

Check that DTCs are not output.

Powertrain > Stop and Start > Trouble Codes
50001 392


b.

for Manual Transaxle

i.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

ii.

Start the engine and warm it up.


iii.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



iv.

Depress the brake pedal and stop the vehicle.


v.

Keep the engine stopped by stop and start control for 1 second or more. (Keep the shift lever in D.)


vi.

Release the brake pedal with the shift lever in D to start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the auxiliary battery voltage is low.



vii.

Check that DTCs are not output.

Powertrain > Stop and Start > Trouble Codes
50001 392



STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the auxiliary battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the auxiliary battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the auxiliary battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

for CVT

i.

Start the engine and warm it up.


ii.

Turn the air conditioning system off.


iii.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



iv.

Depress the brake pedal and stop the vehicle.


v.

Allow the engine to stop by stop and start control. (Keep the shift lever in D.)


vi.

Release the brake pedal with the shift lever in D to start the engine.



b.

for Manual Transaxle

i.

Start the engine and warm it up.


ii.

Turn the air conditioning system off.


iii.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



iv.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


v.

Allow the engine to stop by stop and start control.


vi.

Depress the clutch pedal and start the engine.




WIRING DIAGRAM

A503695E03
0.135,7.656 0.448,7.854 0.313,0.198 10 false A 1.24,1.021 1.573,1.198 0.333,0.177 10 false 4F 1.25,1.833 1.583,2.01 0.333,0.177 10 false 4B 1.281,0.823 1.615,1 0.333,0.177 10 false 1 5.313,0.833 5.646,1.01 0.333,0.177 10 false 12 5.302,2.031 5.635,2.208 0.333,0.177 10 false 10 1.292,2.042 1.625,2.219 0.333,0.177 10 false 9 5.302,2.469 5.635,2.646 0.333,0.177 10 false 36 5.302,2.823 5.635,3 0.333,0.177 10 false 41 5.938,4.198 6.271,4.375 0.333,0.177 10 false 18 5.938,2.031 6.271,2.208 0.333,0.177 10 false 21 5.938,0.823 6.271,1 0.333,0.177 10 false 19 5.865,1.01 6.198,1.188 0.333,0.177 10 false H43 5.896,5.354 6.292,5.521 0.396,0.167 10 false A66 0.156,8.49 2.615,8.74 2.458,0.25 10 false *1: w/o Entry and Start System 4.656,5.479 5.438,5.708 0.781,0.229 10 false BBC NO. 1 4.667,5.906 5.406,6.104 0.74,0.198 10 false BBC NO. 2 2.281,4.542 3.031,4.792 0.75,0.25 10 false IGP-MAIN 3.271,3.281 5.563,3.531 2.292,0.25 10 false Power Distribution Box Assembly 3.417,1.74 3.885,1.948 0.469,0.208 10 false ACC 4.333,1.177 5.052,1.385 0.719,0.208 10 false ECU-ACC 4.198,2.385 5.281,2.698 1.083,0.313 10 false ECU-IGR NO. 4 3.26,2.969 4.021,3.177 0.76,0.208 10 false IGR-NO. 1 5.292,1.01 5.625,1.188 0.333,0.177 10 false 4B 5.292,2.219 5.625,2.396 0.333,0.177 10 false 4B 1.24,2.219 1.573,2.396 0.333,0.177 10 false 4B 5.292,2.646 5.625,2.823 0.333,0.177 10 false 4B 1.24,2.625 1.573,2.802 0.333,0.177 10 false 4B 5.292,2.979 5.625,3.156 0.333,0.177 10 false 4C 6.26,2.219 6.594,2.396 0.333,0.177 10 false IGR 6.24,4.385 6.573,4.563 0.333,0.177 10 false IGP 6.25,5.375 6.719,5.583 0.469,0.208 10 false BIN1 6.26,5.792 6.729,6 0.469,0.208 10 false BIN2 6.063,7.74 7.104,8.281 1.042,0.542 10 false Engine Stop and Start ECU 1.26,2.448 1.594,2.625 0.333,0.177 10 false 39 5.969,5.604 6.302,5.781 0.333,0.177 10 false 1 5.979,5.188 6.313,5.365 0.333,0.177 10 false 3 6.26,1.01 6.729,1.219 0.469,0.208 10 false ACC 4.563,4.552 5.677,4.792 1.115,0.24 10 false ECU-IGP NO. 3 3.635,5.115 4.01,5.333 0.375,0.219 10 false IGP 0.427,7.667 0.76,7.844 0.333,0.177 10 false B 5.875,2.208 6.208,2.385 0.333,0.177 10 false H43 5.885,4.385 6.219,4.563 0.333,0.177 10 false H43 5.875,5.781 6.271,5.948 0.396,0.167 10 false A66 1.24,3.021 1.573,3.198 0.333,0.177 10 false 4B 1.25,2.844 1.563,3.042 0.313,0.198 10 false 11 1.865,2.396 2.625,2.604 0.76,0.208 10 false AM2*2 1.875,2 2.635,2.208 0.76,0.208 10 false AM1*1 1.229,1.417 1.563,1.594 0.333,0.177 10 false 4H 1.281,1.24 1.615,1.417 0.333,0.177 10 false 1 1.281,1.646 1.615,1.823 0.333,0.177 10 false 4 2.25,8.49 4.708,8.74 2.458,0.25 10 false *2: w/ Entry and Start System 0.75,7.667 1.083,7.844 0.333,0.177 10 false C 1.323,7.667 1.656,7.844 0.333,0.177 10 false E 1.031,7.667 1.365,7.844 0.333,0.177 10 false D 1.625,7.667 1.958,7.844 0.333,0.177 10 false F 1.885,7.667 2.219,7.844 0.333,0.177 10 false G 2.156,7.667 2.49,7.844 0.333,0.177 10 false H 1.938,1.208 2.25,1.406 0.313,0.198 10 false IC 2.865,3.26 3.177,3.458 0.313,0.198 10 false 4D 2.594,3.26 2.906,3.458 0.313,0.198 10 false 13 2.125,3.271 2.438,3.469 0.313,0.198 10 false 4C 1.854,3.26 2.167,3.458 0.313,0.198 10 false 17 1.865,7.896 2.177,8.094 0.313,0.198 10 false *2 2.615,7.469 4.438,8 1.823,0.531 10 false External Backup Boost Converter (Eco Run Vehicle Converter Assembly)*3 2.615,7.292 2.927,7.49 0.313,0.198 10 false A3 2.979,6.927 3.438,7.125 0.458,0.198 10 false GND 2.802,6.792 2.958,6.99 0.156,0.198 10 false 6 3.5,6.417 4.115,6.615 0.615,0.198 10 false DON2 6.26,6.427 6.875,6.625 0.615,0.198 10 false DON2 3.594,6.167 4.052,6.365 0.458,0.198 10 false ACC 3.979,6.052 4.292,6.25 0.313,0.198 10 false 3 3.979,6.323 4.135,6.521 0.156,0.198 10 false 1 5.875,6.417 6.333,6.615 0.458,0.198 10 false A67 5.938,6.219 6.25,6.417 0.313,0.198 10 false 19 4.552,7.365 5.938,7.75 1.385,0.385 10 false Stereo Component Amplifier Assembly*3 3.583,6.729 4.042,6.927 0.458,0.198 10 false BO1 3.583,7.135 4.042,7.333 0.458,0.198 10 false ACO 4.813,7.146 5.271,7.344 0.458,0.198 10 false ACC 4.813,6.719 5.125,6.917 0.313,0.198 10 false +B 4.427,7.135 5.042,7.333 0.615,0.198 10 false H137 4.417,6.729 5.031,6.927 0.615,0.198 10 false H136 4.542,6.531 4.698,6.729 0.156,0.198 10 false 1 4.51,6.948 4.823,7.146 0.313,0.198 10 false 12 3.979,6.635 4.135,6.833 0.156,0.198 10 false 5 3.958,7.042 4.271,7.24 0.313,0.198 10 false 12 4.281,8.5 6.74,8.75 2.458,0.25 10 false *3: w/ Stereo Component Amplifier 4.25,6.042 4.531,6.25 0.281,0.208 10 false *3 4.25,6.292 4.531,6.5 0.281,0.208 10 false *3 4.146,6.604 4.427,6.813 0.281,0.208 10 false *3 4.146,7.01 4.427,7.219 0.281,0.208 10 false *3 2.479,6.781 2.76,6.99 0.281,0.208 10 false *3 1.302,7.896 1.615,8.094 0.313,0.198 10 false *2 0.99,7.896 1.302,8.094 0.313,0.198 10 false *1

A456562E01
0.177,1.094 0.49,1.292 0.313,0.198 10 false A 0.469,1.094 0.802,1.271 0.333,0.177 10 false B 5.885,4.344 6.219,4.521 0.333,0.177 10 false 8 5.906,4.771 6.24,4.948 0.333,0.177 10 false 2 5.906,5.198 6.24,5.375 0.333,0.177 10 false 6 0.385,5.281 2.063,5.677 1.677,0.396 10 false BATT-MAIN NO. 1 0.656,6.104 1.125,6.313 0.469,0.208 10 false ALT 2.667,1.813 3.135,2.021 0.469,0.208 10 false IGPD 0.469,7.677 1.844,7.906 1.375,0.229 10 false Auxiliary Battery 2.542,3.208 5.729,3.521 3.188,0.313 10 false Certification ECU (Smart Key ECU Assembly) 2.302,1.813 2.635,1.99 0.333,0.177 10 false H45 6.188,4.542 6.656,4.75 0.469,0.208 10 false GND1 6.188,4.948 6.656,5.156 0.469,0.208 10 false GND2 6.198,5.365 6.667,5.573 0.469,0.208 10 false DGND 6.031,7.521 7.073,8.188 1.042,0.667 10 false Engine Stop and Start ECU 2.677,2.198 3.146,2.406 0.469,0.208 10 false IGRD 2.688,2.906 3.156,3.115 0.469,0.208 10 false +B 2.667,2.563 3.135,2.771 0.469,0.208 10 false ACCD 2.354,1.635 2.688,1.813 0.333,0.177 10 false 24 5.813,4.531 6.302,4.76 0.49,0.229 10 false A66 1.854,5.115 2.188,5.292 0.333,0.177 10 false A81 1.927,4.927 2.24,5.125 0.313,0.198 10 false 1 5.813,4.938 6.302,5.167 0.49,0.229 10 false A66 5.823,5.375 6.313,5.604 0.49,0.229 10 false A67 0.385,5.698 2.063,6.094 1.677,0.396 10 false INP STD NO. 1-2 0.323,6.531 2,6.927 1.677,0.396 10 false INP STD NO. 1-3 1.854,5.531 2.188,5.708 0.333,0.177 10 false A79 1.854,6.354 2.188,6.531 0.333,0.177 10 false A80 1.917,5.344 2.229,5.542 0.313,0.198 10 false 1 1.927,6.167 2.24,6.365 0.313,0.198 10 false 1 2.302,2.188 2.635,2.365 0.333,0.177 10 false H45 2.333,2 2.667,2.177 0.333,0.177 10 false 11 2.292,2.563 2.625,2.74 0.333,0.177 10 false H46 2.344,2.375 2.677,2.552 0.333,0.177 10 false 21 2.292,2.927 2.625,3.104 0.333,0.177 10 false H46 2.375,2.75 2.708,2.927 0.333,0.177 10 false 6 0.771,1.104 1.104,1.281 0.333,0.177 10 false C 1.073,1.104 1.406,1.281 0.333,0.177 10 false E 1.677,1.104 2.01,1.281 0.333,0.177 10 false G 1.385,1.104 1.719,1.281 0.333,0.177 10 false F 1.979,1.104 2.313,1.281 0.333,0.177 10 false H 0.115,0.135 2.396,0.417 2.281,0.281 12 false w/ Entry and Start System: 0.365,6.875 2.948,7.333 2.583,0.458 10 false Fusible Link Block Assembly

A456563E01
0.177,1.094 0.49,1.292 0.313,0.198 10 false A 0.469,1.094 0.802,1.271 0.333,0.177 10 false B 5.885,4.344 6.219,4.521 0.333,0.177 10 false 8 5.906,4.771 6.24,4.948 0.333,0.177 10 false 2 5.906,5.198 6.24,5.375 0.333,0.177 10 false 6 0.385,5.281 2.063,5.677 1.677,0.396 10 false BATT-MAIN NO. 1 0.656,6.104 1.125,6.313 0.469,0.208 10 false ALT 3.229,2.813 3.698,3.021 0.469,0.208 10 false AM1 0.469,7.677 1.844,7.906 1.375,0.229 10 false Auxiliary Battery 3.135,3.552 6.323,3.865 3.188,0.313 10 false Ignition or Starter Switch Assembly 6.188,4.542 6.656,4.75 0.469,0.208 10 false GND1 6.188,4.948 6.656,5.156 0.469,0.208 10 false GND2 6.198,5.365 6.667,5.573 0.469,0.208 10 false DGND 6.031,7.521 7.073,8.188 1.042,0.667 10 false Engine Stop and Start ECU 4.198,2.542 4.667,2.75 0.469,0.208 10 false ACC 4.615,2.542 4.948,2.719 0.333,0.177 10 false 6 5.813,4.531 6.302,4.76 0.49,0.229 10 false A66 1.854,5.115 2.188,5.292 0.333,0.177 10 false A81 1.927,4.927 2.24,5.125 0.313,0.198 10 false 1 5.813,4.938 6.302,5.167 0.49,0.229 10 false A66 5.823,5.375 6.313,5.604 0.49,0.229 10 false A67 0.385,5.698 2.063,6.094 1.677,0.396 10 false INP STD NO. 1-2 0.323,6.531 2,6.927 1.677,0.396 10 false INP STD NO. 1-3 1.854,5.531 2.188,5.708 0.333,0.177 10 false A79 1.854,6.354 2.188,6.531 0.333,0.177 10 false A80 1.917,5.344 2.229,5.542 0.313,0.198 10 false 1 1.927,6.167 2.24,6.365 0.313,0.198 10 false 1 3.021,2.792 3.354,2.969 0.333,0.177 10 false 7 3.146,3.365 3.479,3.542 0.333,0.177 10 false H54 4.625,2.833 4.958,3.01 0.333,0.177 10 false 8 0.771,1.104 1.104,1.281 0.333,0.177 10 false C 1.073,1.104 1.406,1.281 0.333,0.177 10 false D 1.385,1.104 1.719,1.281 0.333,0.177 10 false F 1.979,1.104 2.313,1.281 0.333,0.177 10 false H 0.115,0.135 2.396,0.417 2.281,0.281 12 false w/o Entry and Start System: 0.333,6.854 2.833,7.146 2.5,0.292 10 false Fusible Link Block Assembly 4.26,2.833 4.729,3.042 0.469,0.208 10 false IG1

A456564E06
6.073,8.156 7.125,8.729 1.052,0.573 10 false Engine Stop and Start ECU 6.229,0.448 6.625,0.667 0.396,0.219 10 false B42 6.24,0.833 6.635,1.052 0.396,0.219 10 false AC42 5.958,0.729 6.354,0.948 0.396,0.219 10 false 26 5.948,0.313 6.344,0.531 0.396,0.219 10 false 12 3.958,0.698 4.354,0.917 0.396,0.219 10 false 15 4.135,6.552 4.531,6.771 0.396,0.219 10 false +B 0.938,1.156 1.333,1.375 0.396,0.219 10 false H79 0.938,1.323 4.323,1.594 3.385,0.271 10 false Radio and Display Receiver Assembly*1 3.75,3.219 4.146,3.438 0.396,0.219 10 false B 4.49,7.333 4.885,7.552 0.396,0.219 10 false *5 6.073,7.958 6.469,8.177 0.396,0.219 10 false H43 2.198,3.979 4.458,4.271 2.26,0.292 10 false Meter Mirror Sub-assembly*4 3.594,0.406 3.99,0.625 0.396,0.219 10 false +B1 3.354,0.813 4.042,1.063 0.688,0.25 10 false ACC1*2 2.219,3.813 2.615,4.031 0.396,0.219 10 false H61 3.698,3.51 4.094,3.729 0.396,0.219 10 false IG 3.625,4.958 4.021,5.177 0.396,0.219 10 false IG+ 1.01,5.708 3.333,5.969 2.323,0.26 10 false Combination Meter Assembly 4.094,7.135 4.49,7.354 0.396,0.219 10 false IGR 1.031,5.542 1.427,5.76 0.396,0.219 10 false H6 3.99,0.313 4.385,0.531 0.396,0.219 10 false 4 3.969,4.833 4.365,5.052 0.396,0.219 10 false 38 4,3.385 4.396,3.604 0.396,0.219 10 false 1 5.354,8.052 5.75,8.271 0.396,0.219 10 false I 2.906,8.385 5.396,8.656 2.49,0.271 10 false *6: w/ Entry and Start System 0.146,2.146 2.656,2.469 2.51,0.323 10 false *1: w/ Audio 0.135,2.635 1.948,3.094 1.813,0.458 10 false *2: w/ Radio Receiver without Navigation System 2.177,2.5 4.219,2.885 2.042,0.385 10 false Navigation ECU*3 2.198,2.323 4.448,2.688 2.25,0.365 10 false H82 3.677,1.969 4,2.208 0.323,0.24 10 false +B 3.979,1.833 4.229,2.115 0.25,0.281 10 false 10 0.26,8.396 3.167,8.646 2.906,0.25 10 false *5: w/o Entry and Start System 5.948,1.854 6.344,2.073 0.396,0.219 10 false 11 6.25,1.958 6.646,2.177 0.396,0.219 10 false B43 6.25,4.948 6.646,5.167 0.396,0.219 10 false IG12 5.969,4.833 6.365,5.052 0.396,0.219 10 false 10 6.24,6.531 6.635,6.75 0.396,0.219 10 false B41 6.24,7.115 6.635,7.333 0.396,0.219 10 false IG41 6.031,6.427 6.427,6.646 0.396,0.219 10 false 2 6.042,7 6.438,7.219 0.396,0.219 10 false 3 4,3.083 4.396,3.302 0.396,0.219 10 false 2 0.604,7.573 5.583,7.802 4.979,0.229 10 false Door Control and Tire Pressure Monitoring System Receiver Assembly 4.479,6.74 4.875,6.958 0.396,0.219 10 false *5 4.854,6.74 5.25,6.958 0.396,0.219 10 false *6 4.854,7.323 5.25,7.542 0.396,0.219 10 false *6 4.448,7.125 4.844,7.344 0.396,0.219 10 false O33 4.448,6.531 4.844,6.75 0.396,0.219 10 false O33 4.813,6.531 5.208,6.75 0.396,0.219 10 false O34 4.802,7.125 5.198,7.344 0.396,0.219 10 false O34 0.135,3.26 1.948,3.719 1.813,0.458 10 false *3: w/ Navigation System 0.135,3.781 1.948,4.24 1.813,0.458 10 false *4: w/ Headup Display 4.521,6.323 4.917,6.542 0.396,0.219 10 false 7 4.896,6.323 5.292,6.542 0.396,0.219 10 false 7 4.896,6.927 5.292,7.146 0.396,0.219 10 false 1 4.521,6.927 4.917,7.146 0.396,0.219 10 false 1

A456565E02
6.021,8.135 6.479,8.333 0.458,0.198 10 false H43 6.021,8.313 7.083,9.208 1.063,0.896 10 false Engine Stop and Start ECU 6.24,6.583 6.698,6.781 0.458,0.198 10 false IG31 5.958,6.469 6.417,6.667 0.458,0.198 10 false 23 5.5,0.333 5.958,0.531 0.458,0.198 10 false I 4.135,1.438 4.594,1.625 0.458,0.188 10 false IG+ 1.927,1.823 2.385,2.01 0.458,0.188 10 false H31 4.479,1.333 4.938,1.521 0.458,0.188 10 false 9 1.927,1.979 4.823,2.344 2.896,0.365 10 false Air Conditioning Control Assembly*1 1.938,3.385 2.396,3.573 0.458,0.188 10 false B8 1.927,3.552 4.823,3.917 2.896,0.365 10 false Millimeter Wave Radar Sensor Assembly*2 4.156,3.021 4.615,3.208 0.458,0.188 10 false IGB 4.521,2.885 4.979,3.073 0.458,0.188 10 false 8 4.552,4.49 5.01,4.677 0.458,0.188 10 false 1 4.281,4.625 4.74,4.813 0.458,0.188 10 false IG 1.917,5 2.375,5.188 0.458,0.188 10 false O60 1.927,5.188 4.823,5.552 2.896,0.365 10 false Clearance Warning ECU Assembly*3 1.927,6.958 2.385,7.146 0.458,0.188 10 false H1 1.906,7.146 4.802,7.51 2.896,0.365 10 false Power Steering ECU with Motor Assembly 4.344,6.594 4.802,6.781 0.458,0.188 10 false IG 4.615,6.458 5.073,6.646 0.458,0.188 10 false 1 0.25,8.417 3.104,8.771 2.854,0.354 10 false *1: for Automatic Air Conditioning System 0.24,9.25 3.135,9.615 2.896,0.365 10 false *3: w/ Parking Support Brake System 0.25,8.833 3.083,9.219 2.833,0.385 10 false *2: w/ Toyota Safety Sense

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

for CVT:

When the engine stop and start ECU or oil pump with motor assembly is replaced, check the oil pump with motor assembly.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA

·

If electrical load from additional devices installed to the vehicle (aftermarket audio system, etc.) is applied to the B41, B42, B43, AC42, IG12, IG31 or IG41 terminal in the engine stop and start ECU, the fuse function of the backup boost converter may operate.

If the fuse function of the backup boost converter operates, any systems connected to the B41, B42, B43, AC42, IG12, IG31 or IG41 terminal in the engine stop and start ECU will not operate.

·

If DTCs P279796 (Electromagnetic Oil Pump Component Internal Failure) and P323A19 (Backup Boost Converter "A" Circuit Current Above Threshold) are output simultaneously, troubleshoot for DTC P279796 first, as a malfunction which causes DTC P279796 to be stored may also cause DTC P323A19 to be stored.

·

For wire harness and connector inspection procedures and precautions, refer to "General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE"

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC NO. 1 FUSE AND BBC NO. 2 FUSE)
a.

Disconnect the H43 engine stop and start ECU connector.


b.

Remove the BBC NO. 1 fuse and BBC NO. 2 fuse from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-1 (BIN2) - 2 (BBC NO. 2 fuse) Always Below 1 Ω
A66-3 (BIN1) - 2 (BBC NO. 1 fuse) Always Below 1 Ω
A66-1 (BIN2) - Body ground and other terminals Always 10 kΩ or higher
2 (BBC NO. 2 fuse holder) - Body ground and other terminals Always 10 kΩ or higher
A66-3 (BIN1) - Body ground and other terminals Always 10 kΩ or higher
2 (BBC NO. 1 fuse holder) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H6 combination meter assembly connector.


c.

Disconnect the H1 power steering ECU assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition
H43-10 (IG12) - H6-38 (IG+) Always Below 1 Ω
H43-23 (IG31) - H1-1 (IG) Always Below 1 Ω
H43-10 (IG12) - Body ground and other terminals Always 10 kΩ or higher
H43-23 (IG31) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B



A

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

15.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O34 door control and tire pressure monitoring system receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition
H43-2 (B41) - O34-7 (+B) Always Below 1 Ω
H43-2 (B41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/o Navigation System A
w/ Navigation System B



A

6.CHECK VEHICLE SPECIFICATION

B

17.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
6.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/o Audio A
w/ Audio B



A

7.CHECK VEHICLE SPECIFICATION

B

16.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
7.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/o Headup Display A
w/ Headup Display B



A

8.CHECK VEHICLE SPECIFICATION

B

11.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
8.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
for Manual Air Conditioning System A
for Automatic Air Conditioning System B



A

9.CHECK VEHICLE SPECIFICATION

B

19.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
9.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/o Toyota Safety Sense A
w/ Toyota Safety Sense B



A

10.CHECK VEHICLE SPECIFICATION

B

18.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
10.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/o Parking Support Brake System A
w/ Parking Support Brake System B



A

B

12.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
11.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H61 meter mirror sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition
H43-11 (B43) - H61-2(B) Always Below 1 Ω
H43-11 (B43) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition
H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK ENGINE STOP AND START ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK ENGINE STOP AND START ECU
B412468C59
5,0.25 5.417,0.5 0.417,0.25 3.146,0.26 3.563,0.51 0.417,0.25 1.563,0.26 1.979,0.51 0.417,0.25 0.396,0.146 0.76,0.396 0.365,0.25 10 false *a 5.094,0.302 5.458,0.552 0.365,0.25 10 false H43 3.25,0.313 3.615,0.563 0.365,0.25 10 false A67 1.667,0.313 2.031,0.563 0.365,0.25 10 false A66
*a Component without harness connected
(Engine Stop and Start ECU)
- -


a.

Disconnect the A66, A67 and H43 engine stop and start ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition
H43-2 (B41) - A67-6 (DGND) Always 10 kΩ or higher
H43-12 (B42) - A67-6 (DGND) Always 10 kΩ or higher
H43-11 (B43) - A67-6 (DGND) Always 10 kΩ or higher
H43-3 (IG41) - A67-6 (DGND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK VEHICLE CONDITION (B41, B42, B43 OR IG41 CIRCUIT)

NG

14.CHECK VEHICLE CONDITION (B41, B42, B43 OR IG41 CIRCUIT)
a.

Check that additional devices installed to the vehicle (aftermarket audio system, etc.) are not connected to the B41, B42, B43 or IG41 terminal circuit of the engine stop and start ECU.

Result:
Result Proceed to
Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is not applied. A
Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is applied. B




A

TROUBLESHOOT ECUS CONNECTED TO TERMINALS B41, B42, B43 AND IG41

B

END (REMOVE ADDITIONAL DEVICE)

15.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O33 door control and tire pressure monitoring system receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition
H43-2 (B41) - O33-7 (+B) Always Below 1 Ω
H43-2 (B41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect theH79 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition
H43-12 (B42) - H79-4 (+B1) Always Below 1 Ω
H43-12 (B42) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H82 navigation ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition
H43-11 (B43) - H82-10 (+B) Always Below 1 Ω
H43-11 (B43) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition
H43-3 (IG41) - B8-8 (IGB) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H31 air conditioning control assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition
H43-3 (IG41) - H31-9 (IG+) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR