Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (for Gasoline Model) › 2020.07–2020.09
RM36W0E _51 Engine / Hybrid System _088664 CRUISE CONTROL _0424996 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for Gasoline Model) U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for Gasoline Model)  TERMINALS OF ECU  


CHECK ECM (for M15A-FKS)


A458815E03
1.781,0.156 2.198,0.458 0.417,0.302 5.385,0.188 5.802,0.49 0.417,0.302 1.875,0.229 2.385,0.448 0.51,0.219 11 false D51 5.479,0.26 5.99,0.479 0.51,0.219 11 false A54

HINT:

As a waterproof connector is used for the ECM, voltage, resistance and waveform inspections cannot be performed. The voltage, resistance and waveform values are provided for reference only.


w/o Stop and Start System
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A54-21 (STP) - A54-10 (E1) Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released 0 to 1.5 V
A54-22 (ST1-) - A54-10 (E1) Stop light switch assembly signal
(opposite to STP terminal)
Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A54-27 (CCS) - A54-28 (ECCS) Steering pad switch circuit Cruise control switch not pushed 1 MΩ or higher
Cruise control main switch pushed Below 2.5 Ω
CANCEL switch pushed 228 to 252 Ω
+RES switch pushed 599 to 661 Ω
-SET switch pushed 1463 to 1617 Ω
D51-45 (D) - A54-10 (E1)*1 Clutch switch signal Clutch switch ON
(Clutch pedal depressed)
11 to 14 V
Clutch switch OFF
(Clutch pedal released)
Below 1.0 V
D51-83 (VCNP) - A54-10 (E1)*1 Power source of neutral position switch (specific voltage) Ignition switch ON 4.5 to 5.5 V

*1: for Manual Transaxle


w/ Stop and Start System
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A54-21 (STP) - A54-10 (E1) Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released 0 to 1.5 V
A54-22 (ST1-) - A54-10 (E1) Stop light switch assembly signal
(opposite to STP terminal)
Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A54-27 (CCS) - A54-28 (ECCS) Steering pad switch circuit Cruise control switch not pushed 1 MΩ or higher
Cruise control main switch pushed Below 2.5 Ω
CANCEL switch pushed 228 to 252 Ω
+RES switch pushed 599 to 661 Ω
-SET switch pushed 1463 to 1617 Ω


CHECK ECM (for 1KR-FE)


A459240E02
2.323,0.26 2.781,0.563 0.458,0.302 5.417,0.25 5.875,0.552 0.458,0.302 2.427,0.323 2.885,0.521 0.458,0.198 10 false D50 5.521,0.313 5.979,0.51 0.458,0.198 10 false A55

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
A55-57 (STP) - A55-4 (E1) Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released 0 to 1.5 V
A55-24 (ST1-) - A55-4 (E1) Stop light switch assembly signal
(opposite to STP terminal)
Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A55-60 (CCS) - A55-30 (ECCS) Steering pad switch circuit Cruise control switch not pushed 1 MΩ or higher
Cruise control main switch pushed Below 2.5 Ω
CANCEL switch pushed 228 to 252 Ω
+RES switch pushed 599 to 661 Ω
-SET switch pushed 1463 to 1617 Ω
A55-28 (D)*1 - A55-4 (E1) Clutch switch signal Clutch switch ON
(Clutch pedal depressed)
11 to 14 V
Clutch switch OFF
(Clutch pedal released)
Below 1.0 V
D50-118 (VCNP)*1 - A55-4 (E1) Power source of neutral position switch (specific voltage) Ignition switch ON 4.5 to 5.5 V

*1: w/o Stop and Start System



CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY


NOTICE:
·

Turning the ignition switch to ON with connectors disconnected may cause DTCs to be stored. Make sure to clear the DTCs after inspection has been performed.

·

Do not apply excessive force to the millimeter wave radar sensor assembly connector.



A402620E19
3.365,0.063 3.792,0.302 0.427,0.24 3.49,0.094 3.948,0.292 0.458,0.198 10 false B8

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
B8-8 (IGB) - B8-1 (SGND) Power source Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2
Ignition switch off Below 1 V
B8-1 (SGND) - Body ground Ground Always Below 1 Ω

*1: w/o Stop and Start System

*2: w/ Stop and Start System




CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

Turning the ignition switch ON with connectors disconnected may cause DTCs to be stored. Make sure to clear the DTCs after inspection has been performed.

·

Do not apply excessive force to the forward recognition camera connector.



B472992E26
2.073,0.833 2.458,1.042 0.385,0.208 2.167,0.833 2.479,1.031 0.313,0.198 10 false V10

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
V10-3 (LKSW) - V10-10 (GND) Steering pad switch assembly signal (distance control signal) Ignition switch ON, steering pad switch assembly (vehicle-to-vehicle distance control switch) on Below 1 V
Ignition switch ON, steering pad switch assembly (vehicle-to-vehicle distance control switch) off 4.75 to 5.25 V
V10-10 (GND) - Body ground Ground Always Below 1 Ω
V10-7 (IGB) - V10-10 (GND) Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V