Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (for Gasoline Model) › 2020.07–2020.09
RM36W0E _51 Engine / Hybrid System _088664 CRUISE CONTROL _0424996 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for Gasoline Model) J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for Gasoline Model)  Neutral Position Switch Circuit  


DESCRIPTION

The neutral position switch detects whether the shift lever is in neutral. If the shift lever is moved to neutral for a certain period of time or more, control of vehicle speed by the dynamic radar cruise control system is canceled.

WIRING DIAGRAM

w/o Stop and Start System


C367781E27
0.958,2.094 1.271,2.292 0.313,0.198 10 false IC 2.323,1.115 2.646,1.354 0.323,0.24 10 false W1 2.26,1.99 2.708,2.198 0.448,0.208 10 false TMN 2.385,2.865 2.729,3.052 0.344,0.188 10 false F+ 2.656,1.115 2.885,1.292 0.229,0.177 10 false 1 2.656,1.99 2.885,2.167 0.229,0.177 10 false 2 2.677,2.875 2.906,3.052 0.229,0.177 10 false 3 0.75,3.49 1.219,3.677 0.469,0.188 10 false D44 0.76,3.646 2.427,3.875 1.667,0.229 10 false Neutral Position Switch 5.917,3.792 6.385,3.979 0.469,0.188 10 false D51 5.906,3.99 6.292,4.219 0.385,0.229 10 false ECM 4.875,1.104 5.104,1.281 0.229,0.177 10 false 83 4.813,1.979 5.167,2.26 0.354,0.281 10 false 106 4.875,2.865 5.104,3.042 0.229,0.177 10 false 60 5.146,1.219 5.688,1.427 0.542,0.208 10 false VCNP 5.156,2.094 5.698,2.302 0.542,0.208 10 false NPSW 5.146,2.979 5.688,3.188 0.542,0.208 10 false ENPS 0.25,0.135 2.646,0.417 2.396,0.281 12 false for M15A-FKS:


w/o Stop and Start System


C367781E28
0.958,2.094 1.271,2.292 0.313,0.198 10 false IC 2.323,1.115 2.646,1.354 0.323,0.24 10 false W1 2.26,1.99 2.708,2.198 0.448,0.208 10 false TMN 2.385,2.865 2.729,3.052 0.344,0.188 10 false F+ 2.656,1.115 2.885,1.292 0.229,0.177 10 false 1 2.656,1.99 2.885,2.167 0.229,0.177 10 false 2 2.677,2.875 2.906,3.052 0.229,0.177 10 false 3 0.75,3.49 1.219,3.677 0.469,0.188 10 false D44 0.76,3.646 2.427,3.875 1.667,0.229 10 false Neutral Position Switch 5.917,3.792 6.385,3.979 0.469,0.188 10 false D50 5.906,3.99 6.292,4.219 0.385,0.229 10 false ECM 4.823,1.104 5.146,1.281 0.323,0.177 10 false 118 4.875,1.979 5.229,2.26 0.354,0.281 10 false 88 4.875,2.865 5.104,3.042 0.229,0.177 10 false 87 5.146,1.219 5.688,1.427 0.542,0.208 10 false VCNP 5.156,2.094 5.698,2.302 0.542,0.208 10 false NPSW 5.146,2.979 5.688,3.188 0.542,0.208 10 false ENPS 0.208,0.115 3.083,0.448 2.875,0.333 12 false for 1KR-FE:


w/ Stop and Start System


A382306E18
0.979,2.052 1.292,2.25 0.313,0.198 10 false IC 2.333,1.104 2.646,1.302 0.313,0.198 10 false W1 2.25,1.958 2.615,2.156 0.365,0.198 10 false TMN 2.365,2.844 2.677,3.042 0.313,0.198 10 false F+ 0.792,3.469 1.104,3.667 0.313,0.198 10 false D44 0.792,3.625 2.5,3.906 1.708,0.281 10 false Neutral Position Switch 2.677,1.104 2.99,1.302 0.313,0.198 10 false 1 2.688,1.958 3,2.156 0.313,0.198 10 false 2 2.677,2.844 2.99,3.042 0.313,0.198 10 false 3 4.865,1.104 5.177,1.302 0.313,0.198 10 false 26 4.948,1.969 5.26,2.167 0.313,0.198 10 false 8 4.885,2.854 5.198,3.052 0.313,0.198 10 false 25 5.177,1.104 5.802,1.302 0.625,0.198 10 false TMVC 5.177,1.979 5.823,2.219 0.646,0.24 10 false TMN 5.177,2.865 5.615,3.073 0.438,0.208 10 false TME2 5.167,3.771 5.604,3.979 0.438,0.208 10 false A67 5.167,3.927 6.927,4.323 1.76,0.396 10 false Engine Stop and Start ECU 6.125,0.854 6.563,1.063 0.438,0.208 10 false 5 V


CAUTION / NOTICE / HINT

NOTICE:

Before replacing the ECM, refer to Service Bulletin.


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

2.READ VALUE USING GTS

B

2.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position Switch Neutral position switch status ON or OFF ON: Shift lever in neutral
OFF: Shift lever is in any position other than neutral
-
Powertrain > Engine > Data List
Tester Display
Neutral Position Switch
50003 372 881
OK:

The value of the Data List item changes in accordance with the operation of the shift lever.



Result:
Proceed to
OK
NG



OK

NG

3.CONFIRM MODEL
3.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for M15A-FKS A
for 1KR-FE B



A

4.CHECK HARNESS AND CONNECTOR (ECM - NEUTRAL POSITION SWITCH)

B

6.CHECK HARNESS AND CONNECTOR (ECM - NEUTRAL POSITION SWITCH)
4.CHECK HARNESS AND CONNECTOR (ECM - NEUTRAL POSITION SWITCH)
a.

Disconnect the D51 ECM connector.


b.

Disconnect the D44 neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D51-83 (VCNP) - D44-1 (W1) Always Below 1 Ω
D51-106 (NPSW) - D44-2 (TMN) Always Below 1 Ω
D51-60 (ENPS) - D44-3 (F+) Always Below 1 Ω
D51-83 (VCNP) or D44-1 (W1) - Other terminals and body ground Always 10 kΩ or higher
D51-106 (NPSW) or D44-2 (TMN) - Other terminals and body ground Always 10 kΩ or higher
D51-60 (ENPS) or D44-3 (F+) - Other terminals and body ground Always 10 kΩ or higher



d.

Connect the D44 neutral position switch connector.


e.

Connect the D51 ECM connector.


Result:
Proceed to
OK
NG



OK

5.CHECK ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK ECM
a.

Disconnect the D44 neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D44-1 (W1) - Body ground Ignition switch ON 4.5 to 5.5 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D44-1 (W1) - D44-2 (TMN) Always 995 to 1005 Ω
D44-3 (F+) - Body ground Always Below 1 Ω



d.

Connect the D44 neutral position switch connector.


Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (ECM - NEUTRAL POSITION SWITCH)
a.

Disconnect the D50 ECM connector.


b.

Disconnect the D44 neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D50-118 (VCNP) - D44-1 (W1) Always Below 1 Ω
D50-88 (NPSW) - D44-2 (TMN) Always Below 1 Ω
D50-87 (ENPS) - D44-3 (F+) Always Below 1 Ω
D50-118 (VCNP) or D44-1 (W1) - Other terminals and body ground Always 10 kΩ or higher
D50-88 (NPSW) or D44-2 (TMN) - Other terminals and body ground Always 10 kΩ or higher
D50-87 (ENPS) or D44-3 (F+) - Other terminals and body ground Always 10 kΩ or higher



d.

Connect the D44 neutral position switch connector.


e.

Connect the D50 ECM connector.


Result:
Proceed to
OK
NG



OK

7.CHECK ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK ECM
a.

Disconnect the D44 neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D44-1 (W1) - Body ground Ignition switch ON 4.5 to 5.5 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D44-1 (W1) - D44-2 (TMN) Always 995 to 1005 Ω
D44-3 (F+) - Body ground Always Below 1 Ω



d.

Connect the D44 neutral position switch connector.


Result:
Proceed to
OK
NG



OK

NG