Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2020.07
RM36W0E _58 Vehicle Interior _087823 LIGHTING (INT) _0419674 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Rear Door Courtesy Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the rear door courtesy light switch assembly.

WIRING DIAGRAM

E438205E06
2.917,0.594 3.073,0.792 0.156,0.198 10 false 1 2.917,1.885 3.073,2.083 0.156,0.198 10 false 1 5.854,0.51 6.146,0.719 0.292,0.208 10 false 6 4.146,0.49 4.458,0.688 0.313,0.198 10 false 26 4.156,1.823 4.469,2.021 0.313,0.198 10 false 1 4.125,0.708 4.438,0.906 0.313,0.198 10 false 4E 4.115,2.042 4.427,2.24 0.313,0.198 10 false 4E 5.854,1.813 6.042,1.99 0.188,0.177 10 false 1 6.135,0.531 6.75,0.729 0.615,0.198 10 false LCTY 6.156,1.854 6.771,2.052 0.615,0.198 10 false RCTY 6.563,1.427 6.875,1.625 0.313,0.198 10 false +B 6.563,0.313 6.875,0.51 0.313,0.198 10 false +B 0.969,2.26 1.281,2.458 0.313,0.198 10 false O42 1.021,1.021 4.542,1.219 3.521,0.198 10 false Rear Door Courtesy Light Switch Assembly (LH) 1.01,0.865 1.323,1.063 0.313,0.198 10 false O41 4.333,2.625 5.781,3 1.448,0.375 10 false Power Distribution Box Assembly 5.448,3.052 7.094,3.615 1.646,0.563 10 false Main Body ECU (Multiplex Network Body ECU) 0.969,2.458 4.49,2.656 3.521,0.198 10 false Rear Door Courtesy Light Switch Assembly (RH) 5.802,2.042 6.115,2.24 0.313,0.198 10 false MB 5.792,0.698 6.104,0.896 0.313,0.198 10 false MB

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1

*1: w/ Entry and Start System



PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door Courtesy Switch Status Rear door courtesy light switch assembly RH signal CLOSE or OPEN CLOSE: Rear door RH closed
OPEN: Rear door RH open
-
RL Door Courtesy Switch Status Rear door courtesy light switch assembly LH signal CLOSE or OPEN CLOSE: Rear door LH closed
OPEN: Rear door LH open
-
Body Electrical > Main Body > Data List
Tester Display
RR Door Courtesy Switch Status
RL Door Courtesy Switch Status
50003 449 32,33
OK:

Normal conditions listed above are displayed.



Result:
Result Proceed to
OK A
NG ("RL Door Courtesy Switch Status" is not normal) B
NG ("RR Door Courtesy Switch Status" is not normal) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH)

C

5.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (RH)
2.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH)

OK

3.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH) - POWER DISTRIBUTION BOX ASSEMBLY)

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

3.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH) - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the 4E power distribution box assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O41-1(+) - 4E-26 Always Below 1 Ω
O41-1(+) or 4E-26 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT POWER DISTRIBUTION BOX ASSEMBLY
E438203C08
1.563,0.208 1.938,0.438 0.375,0.229 4.635,0.271 5.01,0.5 0.375,0.229 4.594,0.896 4.458,1.313 true 0.26,0.104 0.5,0.302 0.24,0.198 10 false *a 4.25,1.354 4.688,1.531 0.438,0.177 10 false LCTY 1.667,0.26 2,0.427 0.333,0.167 10 false 4E 4.74,0.313 5.073,0.479 0.333,0.167 10 false MB
*a Component without harness connected
(Power Distribution Box Assembly)
- -


a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4E-26 - MB-6 (LCTY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

5.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (RH)

OK

6.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (RH) - POWER DISTRIBUTION BOX ASSEMBLY)

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (RH)

6.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (RH) - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the 4E power distribution box assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O42-1 (+) - 4E-1 Always Below 1 Ω
O42-1 (+) or 4E-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT POWER DISTRIBUTION BOX ASSEMBLY
E438203C20
1.563,0.208 1.938,0.438 0.375,0.229 4.635,0.271 5.01,0.5 0.375,0.229 4.052,0.896 3.917,1.313 true 0.26,0.104 0.5,0.302 0.24,0.198 10 false *a 3.688,1.344 4.125,1.521 0.438,0.177 10 false RCTY 1.667,0.26 2,0.427 0.333,0.167 10 false 4E 4.74,0.313 5.073,0.479 0.333,0.167 10 false MB
*a Component without harness connected
(Power Distribution Box Assembly)
- -


a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4E-1 - MB-1 (RCTY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG