The automatic light control sensor detects ambient light. The sensor creates an electrical signal based on the amount of light detected, and sends the signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) turns on or off the headlights and taillights according to the signal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B124400 | Light Sensor Circuit Malfunction | Detection condition:
The ignition switch is to ON. Malfunction status:
Either of the following conditions is met: -
Malfunction in automatic light control sensor -
Open or short in automatic light control sensor circuit Malfunction duration:
5 seconds or more |
·
Automatic light control sensor ·
Harness or connector ·
Main body ECU (multiplex network body ECU) |
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1
*1: w/ Entry and Start System
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON.
Wait 10 seconds or more.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| B124400 is output | A |
| B124400 is not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Enter the following menus: Body Electrical / Main Body / Data List.
According to the display on the GTS, read the Data List and check that the value of Light Sensor Illuminance changes while performing the following:
Cover the automatic light control sensor with an opaque object.
Slowly move the opaque object to uncover and then cover the automatic light control sensor.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Light Sensor Illuminance | Light control sensor illuminance | 0 to 8191 lx or Sensor Fail | Value is output according to ambient light level | The displayed value is "0" when no light is detected. |
| Tester Display |
|---|
| Light Sensor Illuminance |
The value changes according to the amount the automatic light control sensor is covered.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Disconnect the H78 automatic light control sensor connector.
Disconnect the H4 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H78-1 (CLTB) - H4-8 (CLTB) | Always | Below 1 Ω |
| H78-4 (CLTS) - H4-20 (CLTS) | Always | Below 1 Ω |
| H78-2 (CLTE) - H4-21 (CLTE) | Always | Below 1 Ω |
| H78-1 (CLTB) or H4-8 (CLTB) - Body ground | Always | 10 kΩ or higher |
| H78-4 (CLTS) or H4-20 (CLTS) - Body ground | Always | 10 kΩ or higher |
| H78-2 (CLTE) or H4-21 (CLTE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Main Body ECU (Multiplex Network Body ECU)) |
Connect the H4 main body ECU (multiplex network body ECU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H4-8 (CLTB) - H4-21 (CLTE) | Ignition switch off | Below 1 V |
| H4-8 (CLTB) - H4-21 (CLTE) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC LIGHT CONTROL SENSOR>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG