Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2020.07
RM36W0E _59 Vehicle Exterior _087824 LIGHTING (EXT) _0419675 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the rear fog light.

WIRING DIAGRAM

E439400E03
1.156,3.177 1.427,3.385 0.271,0.208 10 false W8 1.167,3.333 2.719,3.563 1.552,0.229 10 false Rear Fog Light LED 2.531,2.708 2.677,2.927 0.146,0.219 10 false 2 1.198,2.698 1.5,2.896 0.302,0.198 10 false 1 2.333,2.802 2.635,3 0.302,0.198 10 false B 1.375,2.792 1.677,2.99 0.302,0.198 10 false E 3.042,2.594 3.188,2.854 0.146,0.26 10 false 7 3.021,2.802 3.25,2.99 0.229,0.188 10 false 4E 5.406,4.365 7.063,4.792 1.656,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 3.427,3.979 5.604,4.625 2.177,0.646 10 false Power Distribution Box Assembly 4.24,2.51 4.469,2.698 0.229,0.188 10 false +B 3.667,2.802 3.969,3.01 0.302,0.208 10 false IPD 0.688,5.5 2.427,5.719 1.74,0.219 10 false : CXPI Communication Line 4.781,1.229 5,1.438 0.219,0.208 10 false IC 4.26,3.292 5.365,3.51 1.104,0.219 10 false CXPI Transceiver

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1

·

First, confirm that there is no malfunction in the power integration system. Refer to the How to Proceed with Troubleshooting procedure.

Click herePower Source / Network>POWER DISTRIBUTION>POWER INTEGRATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CXPI communication malfunctions before troubleshooting this symptom.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

*1: w/ Entry and Start System




PROCEDURE

1.READ VALUE USING GTS
a.

Turn the light control switch to the TAIL position.


b.

Turn the rear fog light switch on.


c.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Fog Light Fuse Shut Off Status Rear fog light fuse condition OFF or ON OFF: Rear fog light fuse not shut off
ON: Rear fog light fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Rear Fog Light Fuse Shut Off Status
50003 475 1313
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

3.INSPECT REAR FOG LIGHT ASSEMBLY
2.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Fog Light Output Signal Rear fog light output OFF or ON OFF: Rear fog light is not output
ON: Rear fog light is output
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Rear Fog Light Output Signal
50003 475 1311
OK:

Display changes according to the rear fog light switch operation.



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT REAR FOG LIGHT ASSEMBLY
a.

Disconnect the W8 rear fog light LED connector.


b.

Turn the rear fog light switch off.


c.

Turn the rear fog light switch on.


d.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Fog Light Fuse Shut Off Status Rear fog light fuse condition OFF or ON OFF: Rear fog light fuse not shut off
ON: Rear fog light fuse shut off
-
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

REPLACE REAR FOG LIGHT ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR
4.CHECK HARNESS AND CONNECTOR
a.

Disconnect the W8 rear fog light LED connector.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the 4E power distribution box assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W8-2 (B) or 4E-7 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR