Home › Brake › BRAKE (FRONT) › FRONT BRAKE (for TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _089428 BRAKE (FRONT) _0432145 FRONT BRAKE(for TMMF Made) A

BRAKE (FRONT)  FRONT BRAKE(for TMMF Made)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

C435395C01
1.885,1.333 0.865,1.625 0.865,1.625 1.771,1.24 true 0.646,1.521 0.958,1.677 0.313,0.156 10 false *a
*a Matchmark


a.

Align the matchmarks of the front disc and front axle hub sub-assembly, and install the front disc.

NOTICE:

When replacing the front disc with a new one, select the installation position where the front disc has minimal runout.



Hide 2.INSTALL FRONT DISC BRAKE BUSH DUST BOOT

a.

Install the 2 front disc brake bush dust boots to the front disc brake cylinder assembly.


Hide 47750 3.TEMPORARILY INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY

a.

Using a socket hexagon 7 mm, temporarily install the disc brake cylinder with the 2 front disc brake cylinder slide pins.


Hide 4.INSTALL FRONT DISC BRAKE PAD

C437938

a.

Install the brake pad to the front disc brake cylinder mounting.

NOTICE:

There should be no oil or grease on the friction surfaces of the disc brake pads.



Hide 47748 5.INSTALL FRONT DISC BRAKE ANTI-RATTLE SPRING

C437939C01
0.698,0.698 0.885,0.885 0.188,0.188 10 true *a 1.104,1.719 1.417,1.875 0.313,0.156 10 false *b
*a Sliding Arm A'
*b End A


a.

Push end A of the front disc brake anti-rattle spring into the groove of the front disc brake cylinder assembly and install spring sliding arm A' onto the front disc brake cylinder mounting anchor.


b.
C437940C01
2.385,0.958 2.625,1.146 0.24,0.188 10 true *a
*a End B


Push the front disc brake anti-rattle spring in the direction of the arrow to flex it until end B can be inserted into the groove of the front disc brake cylinder assembly.


c.
C437941C01
2.25,0.656 2.5,0.865 0.25,0.208 10 true *a 1.625,1.854 1.938,2.01 0.313,0.156 10 false *b
*a Sliding Arm B'
*b End B


While pushing end B of the front disc brake anti-rattle spring into the groove of the disc brake cylinder, flex spring sliding arm B' and install arm B' onto the front disc brake cylinder mounting anchor.


d.
C437925

Make sure that the front disc brake anti-rattle spring is securely installed.


Hide 47730 6.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY

a.

Install the front disc brake cylinder assembly with front disc brake cylinder mounting to the steering knuckle with the 2 bolts.

Torque:
107 N*m (1089 kgf*cm, 79 ft.*lbf)


Hide 47715A 7.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

a.

Using a socket hexagon 7 mm, fully tighten the 2 front disc brake cylinder slide pins.

Torque:
27.5 N*m (280 kgf*cm, 20 ft.*lbf)


b.

Install the 2 slide pin caps.


Hide 8.INSTALL FRONT FLEXIBLE HOSE

a.

Connect the flexible hose with a new union bolt and a new gasket.

Torque:
30.4 N*m (310 kgf*cm, 22 ft.*lbf)

HINT:

Install the flexible hose lock securely into the lock hole in the disc brake cylinder.



Hide 10.BLEED CLUTCH LINE (for Manual Transaxle)

Hide 11.INSTALL FRONT WHEEL