Home › General › MAINTENANCE › FRONT DISC BRAKE PAD (for TMC Made) › from 2020.07
RM36W0E _V1 General _088300 MAINTENANCE _0432147 FRONT DISC BRAKE PAD(for TMC Made) A

MAINTENANCE  FRONT DISC BRAKE PAD(for TMC Made)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front brake pad removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model 4 Hub Bolt Type)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DC00, C13DE00, C140000 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure. (for HV Model 4 Hub Bolt Type)

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model 4 Hub Bolt Type)



HINT:
for HV Model 4 Hub Bolt Type:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (for HV Model TMC Made)

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISABLE BRAKE CONTROL (for HV Model TMC Made)

Hide 3.REMOVE FRONT WHEEL

Hide 4.REMOVE FRONT DISC BRAKE PAD

CAUTION:
·

Be careful not to get pinched by the front disc brake cylinder assembly or other parts when removing the front disc brake pads.

·
C368018

After lifting up the front disc brake cylinder assembly, secure it in place before performing any work on it.

·

The front disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.



a.
C435251C01
1.25,2.677 1.563,2.875 0.313,0.198 10 false *a 0.646,2.438 0.958,2.635 0.313,0.198 10 false *b
*a Turn
*b Hold


Hold the front disc brake cylinder slide pin (lower side) and remove the bolt.

NOTICE:

Do not kink or damage the brake line.



b.

Pull the front disc brake cylinder assembly upward.


c.
C430579

Remove the anti-squeal spring from the front disc brake pads.


d.
C435252

Remove the 2 front disc brake pads from the front disc brake cylinder mounting.


Hide 5.REMOVE FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT

a.
C435253C01
0.354,0.531 0.5,0.26 0.5,0.26 0.698,0.26 false 1.344,2 1.792,2 false 1.417,1.063 1.875,1.063 false 2.073,2.74 2.292,2.74 2.292,2.74 2.458,2.396 false 0.813,0.802 0.958,0.531 0.958,0.531 1.156,0.531 false 2.677,3.115 2.896,3.115 2.896,3.115 3.063,2.771 false 1.198,0.438 1.51,0.635 0.313,0.198 10 false *1 1.885,2.646 2.198,2.844 0.313,0.198 10 false *1 0.75,0.167 1.063,0.365 0.313,0.198 10 false *2 2.49,3.021 2.802,3.219 0.313,0.198 10 false *2 1.156,1.917 1.469,2.115 0.313,0.198 10 false *3 1.917,0.979 2.229,1.177 0.313,0.198 10 false *3
*1 Front No. 1 Disc Brake Anti-squeal Shim
*2 Front No. 2 Disc Brake Anti-squeal Shim
*3 Front Disc Brake Pad


Remove the front No. 1 disc brake anti-squeal shim and front No. 2 disc brake anti-squeal shim from each front disc brake pad.


b.
C435254

Using a screwdriver, remove the front disc brake pad wear indicator plate from each front disc brake pad.