Home › Engine / Hybrid System › 1KR-FE (STARTING) › STARTER (w/ Stop And Start System) › from 2020.07
RM36W0E _51 Engine / Hybrid System _091207 1KR-FE STARTING _0432155 STARTER(w/ Stop And Start System) G

1KR-FE STARTING  STARTER(w/ Stop And Start System)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

Perform each of the following tests within 3 to 5 seconds to prevent the coil from burning out.


a.

Perform a pull-in test.

i.
A322637

Remove the nut, and disconnect the field coil lead wire from terminal C.


ii.
A469398C01
1.146,0.958 1,0.75 1,0.75 0.833,0.75 false 3,1.083 2.833,1.083 2.833,1.083 2.573,0.896 false 2.104,1.135 1.667,1.792 1.667,1.792 1.5,1.792 false 0.604,0.667 0.917,0.865 0.313,0.198 10 false *a 3.042,1 3.271,1.198 0.229,0.198 10 false *b 1.302,1.688 1.531,1.885 0.229,0.198 10 false *c
*a Starter Body
*b Terminal C
*c Terminal 50


Connect a battery to the magnet starter switch assembly as shown in the illustration. Check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move outward, replace the starter assembly.



b.

Perform a hold-in test.

i.
A469399C01
1.146,0.958 1,0.75 1,0.75 0.833,0.75 false 2.75,0.583 2.583,0.583 2.583,0.583 2.385,0.906 false 2.104,1.135 1.667,1.792 1.667,1.792 1.5,1.792 false 0.604,0.667 0.917,0.865 0.313,0.198 10 false *a 2.792,0.5 3.021,0.698 0.229,0.198 10 false *b 1.302,1.688 1.531,1.885 0.229,0.198 10 false *c
*a Starter Body
*b Terminal C
*c Terminal 50


While maintaining the battery connections of the pull-in test above, disconnect the negative (-) lead from terminal C. Check that the clutch pinion gear does not return inward.

If the clutch pinion gear returns inward, replace the starter assembly.



c.

Check return operation.

i.
A469400C01
1.198,1.813 1,1.333 1,1.333 0.833,1.333 false 1.583,2.667 1.75,2.667 1.75,2.667 2.135,2.01 true 2.406,1.75 2.583,1.417 2.583,1.417 2.75,1.417 true 0.625,1.24 0.865,1.531 0.24,0.292 10 false *a 2.865,1.313 3.063,1.604 0.198,0.292 10 false *b 1.365,2.563 1.677,2.719 0.313,0.156 10 false *c
*a Starter Body
*b Terminal C
*c Terminal 50


Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the starter assembly.



d.

Perform a no-load performance test.

i.
A322637

Connect the field coil lead wire to terminal C with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


ii.

Hold the starter assembly in a vise between aluminum plates.

NOTICE:

Ensure that the starter assembly is secured in the vise to prevent it from falling out.



iii.
A469401C01
1.25,2.729 1.25,2.427 false 1.667,3.167 1.833,3.167 1.833,3.167 2.156,2.104 true 2.458,1.771 2.99,0.698 2.99,0.698 3.115,0.698 true 1.208,2.792 1.438,3.083 0.229,0.292 10 false *a 3.177,0.594 3.385,0.896 0.208,0.302 10 false *b 1.5,3.083 1.813,3.24 0.313,0.156 10 false *c
*a Starter Body
*b Terminal 30
*c Terminal 50


Connect the battery and an ammeter to the starter assembly as shown in the illustration.

NOTICE:

Do not allow any lead to get caught as the clutch pinion gear operates.



iv.

Check that the starter assembly operates smoothly and steadily while the clutch pinion gear is moving outward.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
Battery positive terminal - Terminal 30 - Terminal 50 11.5 V Below 90 A


If the result is not as specified, replace the starter assembly.



Hide 28160 2.INSPECT STARTER ARMATURE ASSEMBLY

A104566C04
2.242,1.028 1.788,1.482 false 1.607,1.475 1.756,1.651 0.149,0.176 10 *1
*1 Commutator


a.

Check the commutator for open circuits.

i.

Using an ohmmeter, check the resistance between the segments of the commutator.

Standard Resistance
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω

If the result is not as specified, replace the starter armature assembly.



b.
A104565C02
2.832,1.423 3.020,1.604 0.188,0.181 10 *2 0.696,1.16 0.897,1.341 0.201,0.181 10 *1 0.926,1.16 1.326,0.819 false 2.425,0.924 2.92,1.386 false
*1 Armature Coil Core
*2 Commutator


Check the commutator for ground.

i.

Using an ohmmeter, check the resistance between the commutator and armature core.

Standard Resistance
Tester Connection Condition Specified Condition
Commutator - Armature coil core Always 10 or higher

If the result is not as specified, replace the starter armature assembly.



c.

Check the commutator for dirt and burns on the surface.

If the surface is dirty or burnt, restore it with sandpaper (No. 400) or a lathe.


d.
A104575

Check the commutator circumference runout.

i.

Place the commutator on V-blocks.


ii.

Using a dial indicator, measure the circumference runout.

Maximum runout:

0.4 mm (0.0157 in.)


If the runout is greater than the maximum, replace the starter armature assembly.



e.
A382382

Using a vernier caliper, measure the commutator diameter.

Standard diameter:

28.0 mm (1.1024 in.)


Minimum diameter:

27.0 mm (1.0630 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


f.
A382383

Using a vernier caliper, measure the undercut depth of the commutator.

Standard depth:

0.6 mm (0.0236 in.)


Minimum depth:

0.2 mm (0.0079 in.)


If the undercut depth is less than the minimum, adjust it with a hacksaw blade.


Hide 28120 3.INSPECT STARTER YOKE ASSEMBLY

A104567C02
1.021,0.719 0.458,1.031 false 1.396,0.594 2.031,0.198 false 1.781,0.573 1.958,0.458 false 2.177,0.708 2.396,0.813 false 1.708,1 1.844,1.323 false 2.073,0.073 2.26,0.25 0.188,0.177 10 false (+) 1.99,0.302 2.146,0.479 0.156,0.177 10 false (-) 2.427,0.688 2.615,0.865 0.188,0.177 10 false (+) 1.76,1.344 1.917,1.521 0.156,0.177 10 false (-) 0.271,1.063 0.479,1.24 0.208,0.177 10 false *1
*1 Terminal C


a.

Using an ohmmeter, check the resistance between terminal C and the field coil brush lead (+).

NOTICE:

Check the resistance between terminal C and the 2 brush leads (+).


Standard Resistance
Tester Connection Condition Specified Condition
Terminal C - Brush leads (+) Always Below 1 Ω

If the result is not as specified, replace the starter yoke assembly.


b.
A104568E03
1.427,0.542 1.281,0.323 false 1.833,0.521 1.979,0.25 false 2.271,0.677 2.427,0.771 false 1.802,0.99 1.875,1.323 false 1.042,0.198 1.229,0.375 0.188,0.177 10 false (+) 1.792,1.333 1.948,1.51 0.156,0.177 10 false (-) 2.448,0.646 2.635,0.823 0.188,0.177 10 false (+) 2,0.125 2.156,0.302 0.156,0.177 10 false (-)

Using an ohmmeter, check the resistance between the brush lead (+) and the starter yoke.

NOTICE:

Check the resistance between the brush lead (-) and the starter yoke.


Standard Resistance
Tester Connection Condition Specified Condition
Starter yoke - Brush leads (-) Always Below 1 Ω

If the result is not as specified, replace the starter yoke assembly.


Hide 4.INSPECT BRUSH

A382384

a.

Using a vernier caliper, measure the brush length.

Standard length:

10 mm (0.3937 in.)


Minimum length:

6 mm (0.2362 in.)


If the length is less than the minimum, replace the starter yoke assembly.


Hide 28011 5.INSPECT STARTER CLUTCH SUB-ASSEMBLY

A261073C01
1.552,0.061 1.752,0.233 0.201,0.172 10 *a 1.293,1.623 1.480,1.783 0.187,0.160 10 *b
*a Free
*b Lock


a.

Hold the starter clutch and rotate the pinion gear clockwise, and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

If necessary, replace the starter clutch sub-assembly.


Hide 28150 6.INSPECT MAGNET STARTER SWITCH ASSEMBLY

A033580

a.

Check the plunger.

i.

Push in the plunger and check that it returns quickly to its original position.

If necessary, replace the magnet starter switch assembly.



b.
A382514C01
2.229,1.406 2.229,0.24 true 1.906,1.844 1.906,1.458 true 2.198,0.115 2.51,0.313 0.313,0.198 10 false *1 1.833,1.854 2.146,2.052 0.313,0.198 10 false *2
*1 Terminal C
*2 Terminal 50


Check the pull-in coil for an open circuit.

i.

Using an ohmmeter, check the resistance between terminals 50 and C.

Standard Resistance
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω

If the result is not as specified, replace the magnet starter switch assembly.



c.
A382515C01
2.01,1.906 2.01,1.573 true 1.938,1.917 2.25,2.115 0.313,0.198 10 false *1
*1 Terminal 50


Check whether the holding coil has an open circuit.

i.

Using an ohmmeter, check the resistance between terminal 50 and the switch body.

Standard Resistance
Tester Connection Condition Specified Condition
Terminal 50 - Switch body Always Below 2 Ω

If the result is not as specified, replace the magnet starter switch assembly.